UDI R/C U39 Fury Manual de usuario
This product supports GPS positioning and is recommended for outdoor flight!
This wifi camera pinpoint is 5G, please confirm whether the phone is supported.
USER MANUAL
U39 FURY
▲This product is suitable for users over 14 years old.
▲Stay away from the rotating propeller
▲Read the<important statement and safety guidelines >carefully.
Drone
Propeller A
Front
Camera
Rear
Battery indicator
Switch
Front folding arm
Propeller B
Propeller B
Propeller A
Front folding arm
Rear folding arm Rear folding arm
Battery
Front
Rear
Tripod
visual system
Tripod
Front LED (Red) Front LED (Red)
Rear LED (Green)
TF Card slot
2
Unfolding Instruction
The installation method of battery
Connect the batteries of the aircraft to the charging line of the original plant, and then connect to
other USB charging sockets.
Battery indicator flashes when charged. When the charging is
completed, the battery indicator light is always on.
① Folding State
② Rear folding arms unfold
④ Open the tripod
③ Front folding arms unfold
Push to the end
Pull out the battery
▲Only use the original charging line; Adapters with output current of 5V≥2A must be selected.
Battery power is low in the original factory, It must be fully charged before use.
Power adapter (not included)
Original Charging Line ①
②
②
③
Press to unlock the lock
①
Press to unlock the lock
①
Battery charging
3
Installation of TF Card
Transmitter
Insert the TF card into the slot on the belly of the fuselage, and pay attention to the
metal contact surface orientation of the TF card.
Connect the transmitter with the charging line of the original plant, and then connect other USB
charging outlets.
When charging, the transmitter indicator flashes
circularly, and when charging is completed,
the indicator will be on for a long time.
Transmitter charging
▲Only use the original charging line; Adapters with output current of 5V≥2A must be selected.
Video
Left stick /
Trimmer (press down)
GPS switch
Right Stick
Power switch Return
Speed switch
Follow Mode Encircle Mode
Gimbal Rotary Button
Photo
Indicator light
Phone Holder
The original transmitter is low in power, so it should be used after saturation.
* TF card is not included
Power adapter (not included)
Original Charging Line ①
②
③
4
The installation methods of mobile phone holder
The installation methods of mobile phone
①Pull up the clip on the mobile phone.
①
①
Straightening the antenna
②Place the phone in the upper and
lower clamps Between, the clamp
will automatically clamp the mobile
phone .
②
②
* Notice：Don't clip the buttons
on the side of the phone.
Put the phone
clip on the back
of the quasi-
remote controller
and push it to the
end.
Installation Disassemble
Press to unlock the lock
Pull up the clip on
the mobile phone
5
Flight Operations
Transmitter connect with Drone
Mobile phone connect with Drone
Frequency Pairing
①Turn on the power.
② Pull the left stick to the lowest position
and let go, the light goes off slowly.
it indicates the transmitter enters the
frequency state.
③ The drone is placed on the horizontal ground, and long press the power button
for 2 seconds to start the machine. After the navigation light is on for 2 seconds,
the front navigation light flashes and the rear navigation light goes out. At the
same time, the remote control emits a prompt sound of "di", indicating
successful frequency alignment and entering the horizontal calibration of
compass.
horizontal ground
Download and install APP: UDIGPS
This software is suitable for mobile phones in
the IOS and Android system.
For detailed operation, please check the
system “HELP” of APP.
6
Compass calibration
Level Correction Vertical correction
Tips: It’s a must to have the right compass adjustment first each time you start
the drone, or it can’t work normally.
Rotate the aircraft horizontally until the remote control says "di... "Level correction to
complete. When the front navigation light turns to long light and the rear navigation
light flashes, enter vertical correction.rotate the vehicle vertically until the remote
control says "di... "A sound, vertical correction over. The lights are spinning and
flashing.
After the frequency matching is successful, the aircraft automatically searches for
GPS signals. When the blue indicator light of the remote control changes from
flashing to long bright, it makes a sound of "di" at the same time, indicating that the
GPS connection is successful. (when the GPS signal is weak or flying indoors, the
flight height defaults to about 3 meters)
Gyroscope Calibration
Tips: When the drone doesn’t appear to use the trim correction flight status, or
being hit hard (or falling abnormally). thus cause the difficulties in
controlling. Now frequency making and adjustment are needed again.
After the calibration of the compass, the
right control lever of the remote control is
pushed to the lower right corner by 45°, and
the remote control emits a sound of "di",
and the aircraft light flashes and releases,
indicating that the gyroscope has been
calibrated. (drone should be placed on
horizontal ground)
GPS Signal Search
7
Unlocking/locking the motor
Push the left and right stick inward to the 45
degree angle simultaneously.
①On standby drone, motor rotation, drone
unlocked.
②When the drone is not take off, the motor
stops rotating and the drone is locked.
The drone can only take off when the motor
is unlocked.
Control stick operation
Left Stick
Right Stick
Fly to the left
Fly to the right
Forward
Backward
Counterclockwise turn
clockwise turn
Go Up
Go Down
8
Take off
Landing
GPS ON /OFF
GPS is on by default.
GPS off: press the "GPS switch" button, the transmitter will sound "di", the blue
indicator light of the transmitter will flash, and the GPS will be off. (this
function need to be connected to GPS before it can be turned off ).
GPS open: GPS shut down after 5 seconds, click on the "GPS switch" button,
transmitter long blue indicator lights on, GPS to restart.
Note: this function is only used when the motor is locked.
Return
Notice: While returning, the control lever of the transmitter can not control the
drone, it must be waited for the drone to go back to the take-off point.
And after the direction of the drone is directed at the direction of taking
off, in this way right stick can control the drone.
During the flight, press the "return " button, and the transmitter will sound "di", and
the drone will automatically return to the take-off point. (during returning, the
transmitter will continuously sound "di". To stop homing, just press this button again.)
After unlocking the motor, the left control lever slowly pushes up and the aircraft
slowly rises.
During the flight, the left control lever slowly pull down , and the drone slowly lands
until landing.
9
While flying, press down the key, the transmitter sounds “di”, drone enters the
function of following.Now it can be controlled by the user.
The function is standard by the mobile phone APP signal, so it’s a must to make the drone and
APP connected normally, turn on the mobile location service at the same time, otherwise this
function is invalid
Following Function
In flight, press the "encricle" button, and the transmitter will make the sound of "di".
Then it goes to the function of encircling flight. The drone will fly to a default radius
then it waits for the direction controlled by the user. Adjust the speed and direction
of the drone by manipulating the right stick. It is the minimum radius of the default
radius acquiescently ,so drone flies only in the sub range.
Encircling flight
Turn left, the drone flies clockwise;
Move further, the flying speed will
become faster.
Go downside to enlarge the radius
of encircling.
In the state of
encircling flying,
the left stick could
only control the
height of the drone.
Go upward to narrow the radius of
encircling.
Turn right, the drone flies
counterclockwise; Move further,
the speed will become faster.
Note: follow the maximum range distance, within 1000m of the take-off point.
10
Tabla de contenidos
Otros manuales de Cuadricóptero de UDI R/C
UDI R/C
UDI R/C VOYAGER U845Wifi Manual de usuario
UDI R/C
UDI R/C U28W Manual de usuario
UDI R/C
UDI R/C U829 Manual de usuario
UDI R/C
UDI R/C Swan U42 Manual de usuario
UDI R/C
UDI R/C FALCON U842 Manual de usuario
UDI R/C
UDI R/C U842-2 Manual de usuario
UDI R/C
UDI R/C Swan U42 Manual de usuario
UDI R/C
UDI R/C U61 Manual de usuario
UDI R/C
UDI R/C U52G Manual de usuario
