Ubiquiti UniFi ULED-AC Manual de usuario
LED
Network-Managed
LED Panel Powered by AC
Model: ULED-AC
Introduction
Thank you for purchasing the Ubiquiti Networks® UniFi®LED
Panel. This Quick Start Guide is designed to guide you through
installation and includes warranty terms.
Package Contents
LED
Network-Managed
LEDPanel Powered by AC
Model:ULED-AC
UniFi LED Panel Quick Start Guide
System Requirements
• Network switch (for wired configuration), or access point (for
wireless configuration)
• UniFi LED mobile app software
• Mobile device: iOS 10 or Android 5.0
• UniFi LED Controller software
• Computer: UniFi Application Server 0.5.0, Ubuntu 16.04
LTS (Xenial Xerus) 64-bit or Debian 9 64-bit
• Web browser: Google Chrome (Other browsers may have
limited functionality.)
• UniFi Dimmer Switch, model UDIM-AC or UDIM-AT
Installation Requirements
• Phillips screwdriver
• Wire stripper/cutter
• Needle-nose pliers (Optional)
IMPORTANT: The ULED-AC is to be installed by
a qualified electrician in accordance with local
electrical codes and regulations.
IMPORTANT : Le ULED-AC doit être installé par
un électricien qualifié conformément aux codes
électriques locaux et des règlements.
WARNING: TO AVOID FIRE, SHOCK OR DEATH, turn off
power at the circuit breaker or fuse before installing.
AVERTISSEMENT : POUR ÉVITER TOUT RISQUE
D'INCENDIE, D'ÉLECTROCUTION OU DE DÉCÈS;
coupez le courant au niveau du disjoncteur ou du
coupe-circuit ou fusible avant l'installation.
Network Topology Requirements
Network topology requirements are as follows:
• DHCP-enabled network (for the UniFi LED Panel to obtain
an IP address)
• Network switch (for wired configuration), or access point (for
wireless configuration)
• For UniFi Dimmer Switch only:
A UniFi Dimmer Switch connected to the same Layer 2
network as the UniFi LED Panel
• For LED Controller software:
A UniFi Application Server running the UniFi LED Controller
software and connected to the same Layer 2 network as a
the UniFi LED Panel
• For UniFi LED app only:
A UniFi AP connected to the same Layer 2 network as the
UniFi LED Panel
Connection Options
A UniFi LED Panel can use either a wired connection or a
wireless connection. A wired connection to a switch allows
immediate detection and control by the LED Controller, but
if a panel is in a location where Ethernet cabling is not a
reasonable option, then the panel can connect via Wi-Fi to a
UniFi AP.
Control Options
You can control the UniFi LED Panel’s state (on/off) and
brightness. There are three ways to control the Panel:
UniFi Dimmer Switch A user in the immediate vicinity
controls the UniFi LED Panel using the UniFi Dimmer Switch.
UniFi LED App over Layer 2 Network A local user runs the
app to connect to a UniFi AP on the same Layer 2 network as
the UniFi LED Panel.
UniFi LED Controller over Layer 2 Network Alocal user runs
the LED Controller software on the same Layer 2 network as
the UniFi LED Panel.
UniFi PoE Switch
Internet
LAN
WAN
UAP-AC-PRO
UniFi LED
App
UniFi Application Server
UniFi LED
Controller
UDIM-AC
100-277VAC
100-277VAC
ULED-AC
UDIM-AT
802.3af PoE
OR
USG-PRO-4
(DHCP Server)
Sample Network Diagram - Wireless Topology
UniFi PoE Switch
Internet
LAN
WAN
UniFi Application Server
UniFi LED
Controller
100-277VAC
UDIM-AT
802.3af PoE
ULED-AC
Ethernet
UAP-AC-PRO
UniFi LED
App
USG-PRO-4
(DHCP Server)
Sample Network Diagram - Wired Topology
Daisy-Chain Configuration
For installations using multiple UniFi LED Panels in a wired
configuration, we recommend using a daisy chain topology,
asillustrated in the following diagram.
UniFi PoE Switch
Internet
LAN
WAN
UniFi Application Server
UniFi LED
Controller
100-277VAC
UDIM-AT
802.3af PoE
Ethernet
Ethernet
100-277VAC
ULED-AC
ULED-AC
(Additional LED Panels)
USG-PRO-4
(DHCP Server)
Daisy Chain Topology - Sample Network Diagram
Hardware Overview
LED
ULED-AC-XXXXXX
Status LED
State Status
Flashing White Initializing.
Steady White System ready.
Steady Blue Adopted by LED Controller.
Alternating
White/Blue Firmware upgrade is taking place.
Ports
ULED-AC-XXXXXX
Ethernet MAC Sticker
Ethernet Use these 10/100 Ethernet ports to connect to the
LAN or to daisy-chain with other UniFi LED Panels.
MAC Sticker Used to scan the MAC address. For details, refer
to “Quick Setup”.
Button
ULED-AC-XXXXXX
Reset
Reset The Reset button serves two functions:
• Restart Press and release the Reset button quickly.
• Restore to Factory Default Settings Press and hold the
Reset button for more than five seconds.
Terminal Block
ULED-AC-XXXXXX
N L Connections for AC power: N(Neutral), L(Live), and
(Earth ground). Each has two connectors, used to connect
to the power source, and optionally to connect to another
UniFiLED Panel (daisy-chain configuration).
Installation
To install and configure the UniFi LED Panel:
1. Lift the panel and seat it in an opening in the ceiling grid.
2. If the panel will use Wi-Fi to connect to the network, go
to step 3. If the panel will use a wired connection to the
network, connect an Ethernet cable to the Main port.
3. Remove the screw from the cover of the Junction Box and
open the cover.
Otros manuales para UniFi ULED-AC
1
Tabla de contenidos
Otros manuales de Luz de trabajo de Ubiquiti
