Ubiquiti AirFiber AF-11 Manual de usuario

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 1/15

airFiber AF-11 Zip Ties (Qty. 2) airFiber Gigabit PoE (50V, 1.2A)

Power Cord

Package Contents

Antenna Compatibility

The airFiber AF-11 radio is designed for use with the airFiber X antenna model AF-11G35*.

* Check your local/regional regulations for the antenna gain allowed for your application

Installation Requirements

Clear line of sight between airFiber radios

Vertical mounting orientation

Mounting point:

At least 1 m below the highest point on the structure

For tower installations, at least 3 m below the top of the tower

Ground wires – min. 10 AWG (5 mm ) and max. length: 1 m. As a safety precaution,

ground the airFiber radio to grounded masts, poles, towers, or grounding bars.

WARNING:

Failure to properly ground your airFiber radio will void your

warranty.

(Recommended) 2 Outdoor Gigabit PoE surge protectors

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 2/15

Note:

For guidelines about grounding and lightning protection, follow your

local electrical regulatory codes.

High-Band Duplexer(s) (model AF-11-DUP-H) or Low-Band Duplexer(s) (model AF-11-

DUP-L) are required for proper operation:

SISO mode: One Duplexer of either band type

MIMO mode: Two Duplexers of the same band type

(Optional) If not using PoE: DC power source and 12/30 AWG power cable

Outdoor, shielded Category 6 (or above) cabling and shielded RJ-45 connectors are

required for all wired Ethernet connections.

Hardware Overview

Note:

Duplexers must be purchased separately. The Duplexer(s) must match

the terms of your license (frequency bands and polarities allowed).

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 3/15

Chain 0 / Chain 1

Signal LEDs

Low-Band Duplexer High-Band Duplexer

When the Chain 0 or Chain 1 duplexer is installed, its N-type connector is located here,

allowing connection to an RF cable (Chain 1 is covered by the removable duplexer cap).



Signal 4

LED will light blue when on.

Signal 3

LED will light green when on.

Signal 2

LED will light yellow when on.

Signal 1

LED will light red when on.

Bootup to airOS

When powering on, the Power, MIMO, LINK, and Signal 1-4 LEDs light

on. Once the CPU code takes over, the MIMO, LINK, and Signal 1-3 LEDs turn oﬀ. Signal 4

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 4/15

Link LED

MIMO LED

MGMT LED

LED remains lit to indicate the boot sequence is underway.

Initializing airFiber Software

When the airFiber application begins to boot under

airOS®, the Signal 4 LED goes from solidly on to a 2.5 Hz ash. This continues until the

‐

11FX is fully booted.

Signal Level

Once fully booted, the Signal 1-4 LEDs act as a bar graph showing how

close the AF

‐

11FX is to ideal aiming. This is auto-scaled based on the link range, the

antenna gains, and the congured TX power of the remote AF

‐

11FX. Each Signal LED

has three possible states: On, Flashing, and Oﬀ. All Signal LEDs would be solidly on in an

ideal link. For example, if the link has a 1 dB loss, the Signal 4 LED will ash; a 2 dB loss

and the Signal 4 LED will turn oﬀ. The full bar graph LED states are shown below.

dB loss

0 -1 -2 -3 -4 -5 -6

-7 -8 -9 -10 -11 -12 -13

Oﬀ RF Oﬀ

Syncing

Beaconing

Registering

On Operational

Oﬀ Radio Congured in SISO Mode

On Radio Congured in MIMO Mode

Oﬀ No Ethernet Link

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 5/15

Data LED

Power LED

Management Port

Reset Button

Data Port

VDC IN

TX 0, RX 0

RX 1, TX 1

N Connector

On Ethernet Link Established

Random Flash Ethernet Activity

Oﬀ No Ethernet Link

On Ethernet Link Established

Random Flash Ethernet Activity

Oﬀ No Power

On Powered On

10/100 Mbps, secured Ethernet port for conguration. In-Band Management is enabled

by default in the airFiber Conguration Interface. When In-Band Management is

disabled, the MGMT port is the only port that can monitor, congure, and/or update

rmware.

To reset to factory defaults, press and hold the Reset button for more than 10 seconds

while the device is already powered on.

Gigabit PoE port for handling all user traﬃc and powering the device.

The terminal block can be used to power the AF-11 with +50VDC, 1.2A instead of PoE.

The TX and RX SMA ports for the Chain 0 Low-Band Duplexer or High-Band Duplexer

(SISO and MIMO modes).

The RX and TX SMA ports for the Chain 1 Low-Band Duplexer or High-Band Duplexer

(MIMO mode only). In SISO mode, these unused ports are protected by the duplexer

cap.

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 6/15

SMA Port

Female N-type connector into which the antenna cable is plugged.

High-band and low-band channel SMA ports.

Note:

Duplexers are not included with the AF-11. SISO mode requires one Low-

Band Duplexer or one High-Band Duplexer. MIMO mode requires either two Low-

Band Duplexers or two High-Band Duplexers.

Installation Overview

We recommend that you congure your paired AF-11 radios before site installation. The

overview below summarizes the installation procedure, and the subsequent sections

provide detailed installation information.

Install the Duplexer(s) in the AF-11 radio.

Connect the airFiber Gigabit PoE adapter to the DATA port, and connect your computer

to the MGMT port.

Congure the AF-11.

Install a ground wire and mount the AF-11 on the airFiber AF-11G35 antenna (or a

compatible antenna).

At the installation site, install the antenna with the mounted AF-11 radio (see the

antenna’s Quick Start Guide for installation instructions).

Connect the DATA port to your LAN, and connect power (PoE or DC power) to the AF-11.

Establish and optimize the RF link.

Installing the Duplexers

Installing the Duplexer for SISO Mode

Note:

Position the low channel and high channel ports to yield the required

transmit and receive frequencies.

WARNING:

Tighten the collars alternately, a half turn at a time, until both are

fully tightened. Failure to do so may result in damage to the Duplexer.

5. Repeat steps 1-4 for the radio to be used on the other end of the link, ensuring that the

numbers on the second radio’s Duplexer are in the reverse order of the numbers on rst

radio’s Duplexer.

Note:

For example, if the numbers on the rst radio’s Duplexer are (left to right)

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 7/15

1/3, then the numbers on the second radio’s Duplexer should be 3/1.

Installing the Duplexers for MIMO Mode

Note:

MIMO operation requires two licenses, one per polarization and two

Duplexers of the same band type.

Note:

Position the low channel and high channel ports to yield the required

transmit and receive frequencies. Also, ensure that the numbers on the right-

side Duplexer are in the reverse order of the numbers on the left-side Duplexer.

WARNING:

Tighten the collars alternately, a half turn at a time, until both are

fully tightened. Failure to do so may result in damage to the Duplexer.

6. Repeat steps 1-5 for the other radio to be used in the link, ensuring that the numbers on

the second radio’s Duplexers are in the reverse order of the numbers on the rst radio’s

Duplexers.

Note:

For example, if the numbers on the rst radio’s Duplexers are (left to right)

2/4 and 4/2, the numbers on the second radio’s Duplexers should be 4/2 and 2/4.

Connecting Power over Ethernet

WARNING:

Use only the included adapter, model POE-50-60W. Failure to do so can

damage the unit and void the product warranty.

airFiber Conguration

Access the airFiber Conguration Interface and congure the following settings:

Wireless Mode

Congure one AF-11 as the Master and the other as the Slave.

Frequency Setting

The TX Frequency and RX Frequency settings must be the reverse of

each other on both the Master and the Slave.

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 8/15

2. Congure the Ethernet adapter on your computer with a static IP address on the

192.168.1.x subnet.

3. Launch your web browser. Type https://192.168.1.20 in the address eld and press

enter (PC) or return (Mac).

4. The login screen will appear. Enter ubnt in the Username and Password elds. Select

your Country and Language. You must agree to the Terms of Use to use the product.

Click Login.

5. Click Settings, and then click the Wireless tab.

6. Congure the Basic Wireless Settings:

a. For one AF-11, select Master as the Wireless Mode. For the other AF-11, keep the

default, Slave.

b. Enter a name in the Link Name eld. This should be the same on both the Master

and the Slave.

c. If needed, change the Channel Bandwidth, Output Power and/or Maximum

Modulation Rate settings.

7. Congure the TX Frequency and RX Frequency.

8. Congure the Wireless Security:

a. Select the Key Type, HEX or ASCII.

b. For the Key eld:

HEX

Enter 16 bytes (eight, 16-bit hexadecimal digits: 0-9, A-F, or a-f). You can

omit zeroes and use colons, similar to the IPv6 format.

ASCII

Enter a combination of alphanumeric characters (0-9, A-Z, or a-z).

9. Click Save Changes.

10. In-Band Management is enabled by default, so each airFiber radio must have a

unique IP Address. (If the airFiber radios use the same IP Address, you may lose access

to the airFiber radios via the DATA ports.) Click the Network tab.

a. For the Management IP Address option:

DHCP

Keep the default, DHCP, to use DHCP reservation on your router to

assign a unique IP Address.

Static

Change the IP Address, Netmask, and other settings to make them

compatible with your network.

b. Click Save Changes.

11. Disconnect the Ethernet cables from the MGMT and DATA ports on the AF-11.

Conguration of the AF-11 radio is complete.

Note:

One airFiber radio’s TX Frequency is the other radio’s RX Frequency,

and vice versa.

Note:

The airFiber Conguration Interface supports IPv6 formats

excluding dotted quad and “::” (double-colon) notation.

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 9/15

Repeat the instructions in the airFiber Conguration section on the other AF-11 radio.

For details on the airFiber Conguration Interface, refer to the airFiber AF-11FX User Guide,

available at:

ui.com/download/airber

Hardware Installation

Install a Ground Wire

3. At the installation site, secure the other end of the ground wire to a grounded mast,

pole, tower, or grounding bar.

WARNING:

Failure to properly ground your airFiber radio will void your

warranty.

Note:

The ground wire should be as short as possible and no longer than one

meter in length.

Mount to the airFiber AF-11G35 Antenna

1. Attach an RF Cable to an RF connector labeled H or V. Then slide the silicone boot over

the RF connector to protect it.

If using MIMO mode, remove the cap over the second RF connector (V or H) and attach

an RF Cable. Then slide the silicone boot over the RF connector to protect it.



Note:

Align the dot on the side of the shroud with the arrowhead on the dish

antenna.

Connecting Data

3. If you are using DC power, connect the other end of the Ethernet cable to your LAN.

Connecting Power

Note:

For SISO mode, use the RF connector (H or V) as determined by your

licensing. Keep the other RF connector covered with the included Metal Cap.

AF-11 Quick Start Guide

28/09/2020 AF-11 Quick Start Guide

https://dl.ubnt.com/qsg/AF-11/AF-11_EN.html 10/15

Follow the instructions for the source of power that you are using: Power over Ethernet or

DC Power.

Power Over Ethernet

WARNING:

Use only the included adapter, model POE-50-60W. Failure to do so can

damage the unit and void the product warranty.

DC Power

1. Connect a DC power cable to the Terminal Block. (The +VDC and GND can be

connected to either terminal.)

2. Connect the other end of the DC power cable to a DC power supply that supplies

+50VDC.

WARNING:

Applying a negative voltage such as -48VDC will damage the radio.

3. Connect the DC power supply to its source.

Surge Protection

For added protection, install two surge suppressors, such as the Ubiquiti Ethernet Surge

Protector, model ETH-SP-G2, at the end of each link. Install the rst surge protector within

one meter of the airFiber DATA port, and install the second surge protector at the ingress

point of the location housing the wired network equipment.

Alignment

Tips

To accurately align the airFiber radios for best performance, you MUST align only one

end of the link at a time.

You may need to use additional hardware to compensate for issues such as the

improper orientation of a mounting pole or signicant elevation diﬀerences between

airFiber radios.

Establishing a Link

Adjust the positions of the Master and the Slave to establish a link. The following section

features the airFiber X antenna, AF-11G35:

Note:

The Master must be aimed rst at the Slave because the Slave does not

transmit any RF signal until it detects transmissions from the Master.

AF-11 Quick Start Guide

Otros manuales para airFiber AF-11

Otros manuales de Radio de Ubiquiti

Ubiquiti

Ubiquiti B-DB-AC Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-5XHD Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-11FX Manual de usuario

Ubiquiti

Ubiquiti airFiber 11FX Manual de usuario

Ubiquiti

Ubiquiti airFiber 24 Manual de usuario

Ubiquiti

Ubiquiti ROCKET 2AC PRISM Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-24 Manual de usuario

Ubiquiti

Ubiquiti rocket 5ac prism R5AC-PRISM Manual de usuario

Ubiquiti

Ubiquiti GigaBeam GBE-LR Manual de usuario

Ubiquiti

Ubiquiti airMAX IsoStation M5 Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-24 Manual de usuario

Ubiquiti

Ubiquiti PS-5AC Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-5X Manual de usuario

Ubiquiti

Ubiquiti airFiber 5 Manual de usuario

Ubiquiti

Ubiquiti airFiber 5 Manual de usuario

Ubiquiti

Ubiquiti Bullet M BM2-Ti Manual de usuario

Ubiquiti

Ubiquiti NS-5ACL Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-11 Manual de usuario

Ubiquiti

Ubiquiti UniFi UBB Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-11 Manual de usuario

Ubiquiti

Ubiquiti NanoBeam 5AC Gen 2 Manual de usuario

Ubiquiti

Ubiquiti AF-5U Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-24 Manual de usuario

Ubiquiti

Ubiquiti airFiber AF-5XHD Instrucciones de funcionamiento y mantenimiento

Manuales populares de Radio de otras marcas

EisSound

EisSound KBSound iSelect Manual de usuario

Midland

Midland 1001LWX Manual de usuario

Konig

Konig HAV-SR41 Manual de usuario

Roberts

Roberts exprssion Manual de usuario

VDigi

VDigi DD3.0 Manual de usuario

Radio Shack

Radio Shack 21-1863 Manual de usuario

Roberts

Roberts Stream 207 Manual de usuario

Sony

Sony Walkman SRF-M97 Manual de usuario

Stanley

Stanley FatMax FMC770 Manual de usuario

auna

auna DAB-Radio 10026947 Manual de usuario

SOUNDMASTER

SOUNDMASTER UR190 Manual de usuario

HYT

HYT TC-320 Manual de usuario

auna multimedia

auna multimedia Yellowstone 10026851 Manual de usuario

B-Tech

B-Tech GMRS-V2 Manual de usuario

Weierwei

Weierwei VEV-V8 Manual de usuario

SOUNDMASTER

SOUNDMASTER DAB750 Manual de usuario

Telefunken

Telefunken TF-1505 Manual de usuario

Makita

Makita LXRM03 Manual de usuario