Ubiquiti RocketDish RD-2G24 Manual de usuario

airMAX™Carrier Class

2x2 PtP Bridge Dish Antenna

Model: RD-2G24

Introduction

Thank you for purchasing the Ubiquiti Networks™RocketDish™,

an airMAX™Carrier Class 2x2 PtP Bridge Dish Antenna.

This Quick Start Guide is designed to guide you through

the installation of the antenna. This Quick Start Guide also

includes the warranty terms and is for use with the RocketDish,

model RD-2G24.

Package Contents

Dish Reflector Antenna Feed Mount Bracket Pole Clamps

(Qty. 2)

Stabilizer Brackets

(Qty. 2)

Elevation Rod M10x150 Carriage Bolts

(Qty. 4)

airMAX™CarrierClass

2x2PtP Bridge Dish Antenna

Model:RD-2G24

M10x100 Bolts

(Qty. 2)

M10x25 Carriage Bolts

(Qty. 3)

M4 Bolts

(Qty. 4)

Quick Start

Guide

Products may be different from pictures and are subject to change without notice.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable is

designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Installation Requirements

• RocketM2 (sold separately)

• Phillips #1 screwdriver

• 16 mm or 5/8 in. wrench

• 24 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Hardware Overview

Fully Assembled Back View

Elevation Rod

Main Mounting Bracket

Pole Clamp

Stabilizer Brackets

Rocket Mounting Bracket

Antenna Feed

Hardware Installation

Important: Handle the Dish Reflector with care.

Deformations in its shape may reduce the RocketDish's

effectiveness.

1. Each M4 Bolt includes a lock washer. Remove these and use

them to secure the bolts when assembling.

2. The Dish Reflector and Antenna Feed are keyed so the

Antenna Feed can only be installed in a single orientation.

Attach the Antenna Feed to the Dish Reflector in the

following steps:

a. Line up the alignment pin on the Dish Reflector with the

hole on the Antenna Feed.

b. Insert the four M4 Bolts into the Antenna Feed and Dish

Reflector.

c. Tighten the four M4 Bolts.

Important: Do not handle the RocketDish by the Antenna

Feed once the feed is connected.

3. Attach the RocketM to the Dish Reflector.

a. Align the mounting tabs on the back of the RocketM

with the Rocket Mounting Bracket located below the

Antenna Feed.

b. Slide the RocketM down to lock it into place.

4. Attach the RF Cables to the connectors labeled Chain 0 and

Chain 1 on the RocketM.

5. The Elevation Rod includes washers and nuts. Remove one

washer, one spring lock washer, and one nut. Use them to

secure the Elevation Rod when assembling.

6. Attach the Elevation Rod to the Main Mounting Bracket.

a. Insert the Elevation Rod into the Main Mounting Bracket.

b. Secure the Elevation Rod with the washer, spring lock

washer, and nut.

7. Each M10x150 Carriage Bolt includes a washer, spring lock

washer, and nut. Remove these and use them to secure the

bolts when assembling in step 13.

8. Insert the four M10x150 Carriage Bolts into the Main

Mounting Bracket.

9. Each M10x25 Carriage Bolt includes a washer, spring lock

washer, and nut. Remove these and use them to secure the

bolts when assembling.

10. Attach the RocketDish to the Main Mounting Bracket.

a. Insert one M10x25 Carriage Bolt into the RocketDish and

Elevation Rod.

b. Insert two M10x25 Carriage Bolts into the RocketDish

and lower section of the Main Mounting Bracket.

c. Secure each M10x25 Carriage Bolt with one washer, one

spring lock washer, and one nut.

11. Each M10x100 Bolt includes a washer, spring lock washer,

and nut. Remove these and use them to secure the bolts

when assembling.

12. Attach the Stabilizer Brackets to the pole just beneath the

area where the RocketDish will be attached.

Note: The mounting assembly can accommodate a

Ø 1.5" - 4.0" pole.

a. Place one Stabilizer Bracket on each side of the pole.

b. Insert the two M10x100 Bolts into the Stabilizer Brackets.

c. Secure each M10x100 Bolt with one washer, one spring

lock washer, and one nut.

d. Tighten the nuts to approximately 50N-m(37lb-ft).

13. Attach the Main Mounting Bracket to the pole just above

the Stabilizer Brackets.

a. Slide a Pole Clamp over each pair of M10x150

CarriageBolts.

b. Secure each M10x150 Carriage Bolt with one washer,

one spring lock washer, and one nut.

14. Visually align the azimuth and elevation.

a. To adjust the azimuth, rotate the RocketDish while it is

supported by the Stabilizer Brackets.

b. To adjust the elevation angle, tighten or loosen the nuts

on the Elevation Rod so that the RocketDish is set to the

desired tilt.

c. Tighten all bolts and nuts to approximately

50N-m(37lb-ft) or less to avoid deforming the pole.

Nuts

Otros manuales para RocketDish RD-2G24

Tabla de contenidos

Otros manuales de Antena de Ubiquiti

Ubiquiti

Ubiquiti NBE-M2-400 NanoBeam M Manual de usuario

Ubiquiti

Ubiquiti airMAX Titanium Sector AM-VSG-Ti Manual de usuario

Ubiquiti

Ubiquiti airMAX Omni AMO-5G13 Manual de usuario

Ubiquiti

Ubiquiti Horn-5-45 Manual de usuario

Ubiquiti

Ubiquiti airMAX AM-5G20-90 Manual de usuario

Ubiquiti

Ubiquiti NanoBridge M3 Manual de usuario

Ubiquiti

Ubiquiti Horn-5-60 Manual de usuario

Ubiquiti

Ubiquiti RocketDish RD-5G31-AC Manual de usuario

Ubiquiti

Ubiquiti AM-5G16-120 Manual de usuario

Ubiquiti

Ubiquiti airMAX Omni AMO-5G10 Manual de usuario

Ubiquiti

Ubiquiti airMAX Sector AM-2G16-90 Manual de usuario

Ubiquiti

Ubiquiti AirMax Sector Manual de usuario

Ubiquiti

Ubiquiti AMO-3G12 Manual de usuario

Ubiquiti

Ubiquiti airMAX Omni Manual de usuario

Ubiquiti

Ubiquiti airMAX AM-5G20-90 Manual de usuario

Ubiquiti

Ubiquiti airGrid M2 HP AG-HP-2G16 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500-ISO Manual de usuario

Ubiquiti

Ubiquiti GBE-LR Manual de usuario

Ubiquiti

Ubiquiti airMAX airGrid M5HP Manual de usuario

Ubiquiti

Ubiquiti airMAX Omni AMO-5G10 Manual de usuario

Ubiquiti

Ubiquiti RocketDish RD-5G30 Manual de usuario

Ubiquiti

Ubiquiti PBE-2AC-400 Manual de usuario

Ubiquiti

Ubiquiti LTU-Rocket Manual de usuario

Ubiquiti

Ubiquiti AM-M-V5G-Ti Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario