U-tec UltraloqUL3 Manual de usuario

Ultraloq UL3

Fingerprint and Touchscreen

Smart Lock

User Guide ( V1.3 )

Welcome

- 1 -

To ensure the best warranty coverage and customer

service, please register your product at

http://store.u-tec.com/account/login

Warranty Statements

See www.u-tec.com for speciﬁc warranty details and

limitations, or contact U-tec’s Customer Service .

* This guide contains important information about your lock!

Operation Video

Please watch our easy step by step operation video

before attempting to use your Ultraloq UL3 Fingerprint

and Touchscreen Smart Lock.

If you have questions regarding the installation process

please contact us at [email protected]

www.u-tec.com/support

Need Help?

For technical documents and more

Please visit www.u-tec.com/support

Tel: 844-HEY-UTEC (844-439-8832)

Email: [email protected]

- 2 -

Exterior

Interior

Lock Parts

Touchscreen

Fingerprint reader

Message display screen

Backup key hole

Restart button

Battery Cover

Reset Button

SN Label

Reset Button: Used to reset the lock to factory default settings.

Battery Cover: Used to cover battery and product label. A Quick Guide

is printed inside the battery cover.

Backup Key Hole: Used to insert the key to unlock.

Restart Button: Used to jump start the lock if activation fails.

Fingerprint Reader: Used to press ﬁnger and unlock from the outside.

Touchscreen: Used to enter the code and unlock from outside.

- Numbers Return to previous Conﬁrm

0 9

Lock Operation

- 3 -

1. Touch lock with back of hand or ﬁngers to activate the lock.

2. Input user PIN code to unlock.

3. Rotate handle and open the door.

Open door from outside with

user PIN code

Press ﬁnger on ﬁngerprint reader or touch lock with the

back of hand or ﬁngers.

The lock will turn off again after 20 seconds if there are

no other inputs.

Use a microﬁber cloth and wipe across the ﬁngerprint

reader surface and the touch screen.

Clean the ﬁngerprint reader and

touchscreen

Lock Activation

1. Press ﬁnger on the ﬁngerprint reader to activate and unlock.

2. Rotate the handle and open the door.

Open door from outside with

ﬁngerprint

1. Rotate the handle and open the door.

Open door from inside

- 4 -

When you activate the lock and see the message “Low

battery”, you should replace the batteries.

Use 3 high-quality alkaline AA batteries for replacement.

Replace battery

Emergency Key Override can be used when the battery is

dead, or when no valid User Code is known.

The key hole is on the bottom of the lock. Insert the key and

rotate to unlock, just like any lock. Take good care of your

emergency keys.

Emergency Key Override

Ultraloq UL3 supports up to 16-digit Vague Code.Just enter

any 16-digit code, as long asa correct codeis included in

what you entered, you canopen the door.

Vague Code

1. Place a ﬁnger ﬂat on the sensor’s surface.

2. Place a ﬁnger in the center of the sensor.

Place Finger

- 5 -

1 2 3 4 5 6 X X X X X X

1 2 3 4 5 6

X X X X X X

1 2 3 4 5 6

X X X X X X

Example

User Code:123456

Vague Code Method

Admin account must be created ﬁrst before any other

programming.Then use the Admin account to add or delete

the other accounts.

Factory default setting is that any ﬁngerprint or PIN code

can open the door.

Factory Defaults

Lock Programming

- 6 -

User PIN code can be 4 to 8 numbers.

User PIN code

User ID can be 1 to 8 numbers.

User ID number

You can register up to 95 users with ﬁngerprint and PIN code.

Limit the number of users on lock

1. Activate lock. Press and hold for 3 seconds to into menu.

2. Input number to select functions:

3. Press and follow the displayed messages to setup.

Basic programming steps

1to add User

to delete User

to add Admin

to delete Admin

Reset the lock

Remove the battery cover. The reset button is under the

serial number label. Find a small paper clip and stick one end

into the reset button hole while the lock is active. Press and

hold the reset button for 3 seconds until a beep is audible.

All user info will be deleted.

Add Admin First

- 7 -

Admin account must be created ﬁrst prior to

any other programming.

Activate Lock No User

Add adminPress and hold for 3 sec

Finger or codePress

Enter againPress ﬁnger or input a PIN code

SuccessPress ﬁnger or input a PIN code

Add User

- 8 -

Activate Lock Welcome

Admin codePress and hold for 3 sec

MenuPress admin ﬁnger or enter admin PIN code

Add userPress 1

Press Enter user ID

Enter user ID Finger or code

Press ﬁnger or input a PIN code Enter again

Press ﬁnger or input a PIN code Success

Delete User

- 9 -

Activate Lock Welcome

Admin codePress and hold for 3 sec

Press admin ﬁnger or enter admin PIN code Menu

Delete userPress 2

Press Enter user ID

Enter user ID Enter again

Enter user ID again Success

Tabla de contenidos

Otros manuales de Cerrar de U-tec

U-tec

U-tec Ultraloq UL300 Manual de usuario

U-tec

U-tec Ultraloq U-Bolt Pro Manual de usuario

U-tec

U-tec Ultraloq LATCH 5 FINGERPRINT Manual de usuario