Tyco TY-FRL Series Manual de usuario

Worldwide

Contacts

www.tyco-ﬁre.com

General

Description

The Series TY-FRL, 2.8, 5.6, and 8.0 K-

factor, Upright and Pendent Sprinklers

described in this data sheet are quick

response -standard coverage, solder

type spray sprinklers designed for use

in light and ordinary hazard, commer-

cial occupancies such as banks, ho-

tels, shopping malls, schools, hospi-

tals, etc.

The recessed version of the 2.8 and

5.6 K-factor, Series TY-FRL Pendent

Sprinkler, where applicable, is intend-

ed for use in areas with a ﬁnished ceil-

ing. It uses a two-piece Style 20 (1/2

inch NPT) Recessed Escutcheon. The

Recessed Escutcheon provides 1/4

inch (6,4 mm) of recessed adjustment

or up to 1/2 inch (12,7 mm) of total ad-

justment from the ﬂush pen-dent po-

sition. The adjustment provided by

the Recessed Escutcheon reduces

the accuracy to which the ﬁxed pipe

drops to the sprinklers must be cut.

An intermediate level version of the

5.6 and 8.0 K-factor, Series TY-FRL

Pendent Sprinkler can be obtained

by utilizing the Series TY-FRL Pen-

dent Sprinkler in combination with the

Model S4 Shield.

NOTICE

The Series TY-FRL Sprinklers de-

scribed herein must be installed and

maintained in compliance with this

document, as well as with the appli-

cable standards of the National Fire

Protection Association, in addition to

the standards of any other authorities

having jurisdiction. Failure to do so

may impair the performance of these

devices.

The owner is responsible for maintain-

ing their ﬁre protection system and

devices in proper operating condi-

tion. The installing contractor or sprin-

kler manufacturer should be contact-

ed with any questions.

Sprinkler

Identiﬁcation

Numbers

T Y112 1. . . . . . Upright 2.8K, 1/2”NPT

TY1221 ....Pendent 2.8K, 1/2”NPT

TY3121 .....Upright 5.6K, 1/2”NPT

TY3221 .... Pendent 5.6K, 1/2”NPT

TY4121......Upright 8.0K, 3/4”NPT

TY4221 .... Pendent 8.0K, 3/4”NPT

TY1121 is a redesignation for S1879

and G8973.

TY1221 is a redesignation for S1880

and G8971.

TY3121 is a redesignation for S1864

and G8974.

TY3221 is a redesignation for S1865

and G8972.

TY4121 is a redesignation for S1866

and G8174.

TY4221 is a redesignation for S1867

and G8172.

Series TY-FRL — 2.8, 5.6, and 8.0 K-factor

Upright, Pendent, and Recessed Pendent Sprinklers

Quick Response, Standard Coverage

Page 1 of 6 MARCH 2013 TFP130

Worldwide

Contacts

www.tyco-ﬁre.com

IMPORTANT

Always refer to Technical Data

Sheet TFP700 for the “INSTALLER

WARNING” that provides cautions

with respect to handling and instal-

lation of sprinkler systems and com-

ponents. Improper handling and in-

stallation can permanently damage

a sprinkler system or its compo-

nents and cause the sprinkler to fail

to operate in a ﬁre situation or cause

it to operate prematurely.

* **

** *

UPRIGHT PENDENT CROSS SECTIONRECESSED PENDENT

7/16"

(11,1 mm)

NOMINAL

MAKE-IN

WRENCH

FLANGES

ESCUTCHEON

PLATE SEATING

SURFACE

WRENCH

AREA

STYLE 20

RECESSED

ESCUTCHEON

Pipe thread connections per

ISO 7-1 can be provided on

special request.

Temperature rating

is indicated on

Deector.

DEFLECTOR 2-7/8" (73,0 mm) DIA.

Deector

Strut

Frame

Link

Assembly Seal

9-Bushing

Button

1/2" NPT

Hook4 -

6-Ejection

Spring

DEFLECTOR

2-11/16"

(68,3 mm)

(50,8 mm)

2-11/16"

(68,3 mm)

FIGURE 1

QUICK RESPONSE SERIES TY-FRL UPRIGHT (TY1121) AND PENDENT (TY1221) SPRINKLERS

2.8 K-FACTOR, 1/2 INCH NPT

* **

** *

UPRIGHT PENDENT CROSS SECTIONRECESSED PENDENT

7/16"

(11,1 mm)

NOMINAL

MAKE-IN

WRENCH

FLANGES

ESCUTCHEON

PLATE SEATING

SURFACE

WRENCH

AREA

STYLE 20

RECESSED

ESCUTCHEON

Pipe thread connections per

ISO 7-1 can be provided on

special request.

Temperature rating

is indicated on

Deector.

DEFLECTOR 2-7/8" (73,0 mm) DIA.

Deector

Strut

Frame

Link

Assembly Seal

Button

1/2" NPT

Hook4 -

6-Ejection

Spring

DEFLECTOR

2-11/16"

(68,3 mm)

(50,8 mm)

2-11/16"

(68,3 mm)

FIGURE 2

QUICK RESPONSE SERIES TY-FRL UPRIGHT (TY3121) AND PENDENT (TY3221) SPRINKLERS

5.6 K-FACTOR, 1/2 INCH NPT

TFP130

Page 2 of 6

Technical

Data

Approvals

UL and C-UL Listed. FM, NYC, and

LPCB Approved. (Refer to Table A for

complete approval information includ-

ing corrosion resistant status.)

Maximum Working Pressure

175 psi (12,1 bar)

Discharge Coefﬁcient

K=2.8 GPM/psi1/2 (40,3 LPM/bar1/2)

K=5.6 GPM/psi1/2 (80,6 LPM/bar1/2)

K=8.0 GPM/psi1/2 (115,2 LPM/bar1/2)

Temperature Ratings

Refer to Table A

Finishes

Sprinkler: Refer to Table A Recessed

Escutcheon: White Coated, Chrome

Plated, or Brass Plated

Physical Characteristics

Frame Bronze

Strut .......................Monel

Deﬂector................... Bronze

Hook.......................Monel

Link Assembly . . . . . . . . . . . . . . . Nickel

Ejection Spring. . . . . . . . . . . . . . Inconel

Button..................... Bronze

Seal .....................TEFLON

Bushing (2.8K only) . . . . . . . . . . . Brass

Operation

The fusible link (heat collector) assem-

bly is comprised of two halves that

are joined together by a thin layer of

solder. When the rated temperature

is reached, the solder melts and the

two link halves separate, allowing the

sprinkler to operate.

Design Criteria

The Series TY-FRL Pendent and Up-

right Sprinklers are intended for ﬁre

protection systems designed in accor-

dance with the standard installation

rules recognized by the applicable

Listing or Approval agency (e.g., UL

Listing is based on the requirements

of NFPA 13, and FM Approval is based

on the requirements of FM’s Loss Pre-

vention Data Sheets). Only the Style

20 Recessed Escutcheon, as appli-

cable, is to be used for recessed pen-

dent installations.

Installation

The Series TY-FRL Sprinklers must

be installed in accordance with this

section.

A leak tight 1/2 inch NPT sprinkler

joint should be obtained with a torque

of 7 to 14 ft./lbs. (9,5 to 19,0 Nm). A

maximum of 21 ft. lbs. (28,5 Nm) of

torque may be used to install sprin-

klers with 1/2 NPT connections. A

leak tight 3/4 inch NPT sprinkler joint

should be obtained with a torque of 10

to 20 ft./lbs. (13,4 to 26,8 Nm). A max-

imum of 30 ft./lbs. (40,7 Nm) of torque

is to be used to install sprinklers with

3/4 NPT connections. Higher levels of

torque may distort the sprinkler in-

let and cause leakage or impairment

of the sprinkler.

Do not attempt to make-up for insuf-

ﬁcient adjustment in the escutcheon

plate by under-or over-tightening the

sprinkler. Readjust the position of the

sprinkler ﬁtting to suit.

Series TY-FRL Pendent and Upright

Sprinkler Installation

The Series TY-FRL Pendent and Up-

right Sprinklers must be installed in

accordance with this section.

Step 1. Pendent sprinklers are to be

installed in the pendent position, and

upright sprinklers are to be installed in

the upright position.

Step 2. With pipe thread sealant ap-

plied to the pipe threads, hand tighten

the sprinkler into the sprinkler ﬁtting.

UPRIGHT PENDENT CROSS SECTION

WRENCH

AREA

Pipe thread connections

per ISO 7-1 can be

provided on special

request.

Temperature rating is

indicated on Deector.

Deector

Strut

Frame

Link

Assembly

Seal

Button

WRENCH

FLANGES

Hook4 -

Ejection

Spring

DEFLECTOR

CEILING PLATE

SEATING SURFACE

2-3/16"

(55,6 mm)

DEFLECTOR

2-13/16"

(71,4 mm)

1/2"

(12,7 mm)

NOMINAL

MAKE-IN

2-15/16"

(74,6 mm)

3/4" NPT

FIGURE 3

QUICK RESPONSE SERIES TY-FRL UPRIGHT (TY4121) AND PENDENT (TY4221) SPRINKLERS

8.0 K-FACTOR, 3/4 INCH NPT

TFP130

Page 3 of 6

SPRINKLER FINISH

KTYPE TEMP.

RATING FRAME

COLOR

CODE

NATURAL

BRASS CHROME

PLATED

2.8

1/2”

NPT

PENDENT

(TY1221)

165°F (74°C) Unpainted

1, 2, 5

212°F (100°C) White

UPRIGHT

(T Y1121)

165°F (74°C) Unpainted

212°F (100°C) White

RECESSED

PENDENT

(TY1221 w/Style 20)

165°F (74°C) Unpainted

212°F (100°C) White

5.6

1/2”

NPT

PENDENT

(TY3221)

165°F (74°C) Unpainted 1, 2, 3, 4, 5

212°F (100°C) White 1, 2, 3, 5

UPRIGHT

(TY3121)

165°F (74°C) Unpainted 1, 2, 3, 4, 5

212°F (100°C) White 1, 2, 3, 5

RECESSED

PENDENT

(TY3221 w/Style 20)

165°F (74°C) Unpainted

1, 2, 5

212°F (100°C) White

8.0

3/4”

NPT

PENDENT

(TY4221)

165°F (74°C) Unpainted

1, 2, 3, 5

212°F (100°C) White

UPRIGHT

(TY4121)

165°F (74°C) Unpainted

212°F (100°C) White

Step 3. Tighten the sprinkler into the

sprinkler ﬁtting using only the W-Type

9 Sprinkler Wrench (Ref. Figure 6).

With reference to Figures 1, 2, and 3,

the W-Type 9 Sprinkler Wrench is to

be applied to the wrench area.

The Series TY-FRL Recessed Pendent

Sprinklers must be installed in accor-

dance with the following instructions.

Step A. After installing the Style 20

Mounting Plate, as applicable, over

the sprinkler threads and with pipe

thread sealant applied to the pipe

threads, hand tighten the sprinkler into

the sprinkler ﬁtting.

Step B. Tighten the sprinkler into the

sprinkler ﬁtting using only the W-Type

12 Recessed Sprinkler Wrench (Ref.

Figure 7). With reference to Figure 1,

or 2, the W-Type 12 Recessed Sprin-

kler Wrench is to be applied to the

sprinkler wrenching ﬂanges.

Step C. After the ceiling has been in-

stalled or the ﬁnish coat has been ap-

plied, slide on the Style 20 Closure

over the Series TY-FRL Sprinkler and

push the Closure over the Mounting

Plate until its ﬂange comes in contact

with the ceiling.

NOTES:

(1) Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers

(2) Listed by Underwriters Laboratories, Inc. for use in Canada (C-UL) as Quick Response Sprinklers.

(3) Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers.

(4) Approved by the Loss Prevention Certication Board (LPCB Ref. No. 094a/03) as Quick Response

Sprinklers.

(5) Approved by the City of New York under MEA112-04-E. N/A: Not Available

TABLE A

LABORATORY LISTINGS AND APPROVALS

TFP130

Page 4 of 6

Care and

Maintenance

The Series TY-FRL Sprinklers must

be maintained and serviced in accor-

dance with this section.

Before closing a ﬁre protection sys-

tem main control valve for mainte-

nance work on the ﬁre protection sys-

tem that it controls, permission to shut

down the affected ﬁre protection sys-

tem must be obtained from the prop-

er authorities and all personnel who

may be affected by this action must

be notiﬁed.

Absence of an escutcheon, which is

used to cover a clearance hole, may

delay the time to sprinkler operation in

a ﬁre situation.

Sprinklers that are found to be leaking

or exhibiting visible signs of corrosion

must be replaced.

Automatic sprinklers must never be

painted, plated, coated or otherwise

altered after leaving the factory. Modi-

ﬁed or over-heated sprinklers must be

replaced.

Care must be exercised to avoid dam-

age to the sprinklers -before, during,

and after installation. Sprinklers dam-

aged by dropping, striking, wrench

twist/slippage, or the like, must be

replaced.

The owner is responsible for the in-

spection, testing, and maintenance

of their ﬁre protection system and de-

vices in compliance with this docu-

ment, as well as with the applicable

standards of the National Fire Protec-

tion Association (e.g., NFPA 25), in

addition to the standards of any oth-

er authorities having jurisdiction. The

installing contractor or sprinkler man-

ufacturer should be contacted relative

to any questions.

It is recommended that automatic

sprinkler systems be inspected, test-

ed, and maintained by a qualiﬁed In-

spection Service in accordance with

local requirements and/or national

codes.

CLOSURE

MOUNTING

SURFACE

FACE OF

SPRINKLER

FITTING

1/2±1/8"

(12,7±3,2 mm) 1/4" (6,4 mm)

TY-FRL

2-1/4" DIA.

(57,2 mm)

1-1/2" (38,1 mm)

1-3/4" (44,5 mm)

MOUNTING

PLATE

1/8"

(3,2 mm)

2-7/8" DIA.

(73,0 mm)

1/2" (12,7 mm)

FIGURE 4

SERIES TY-FRL (TY1221) RECESSED PENDENT SPRINKLER ASSEMBLY

WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT

STYLE 20 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT

CLOSURE

MOUNTING

SURFACE

FACE OF

SPRINKLER

FITTING

1/2±1/8"

(12,7±3,2 mm) 1/4" (6,4 mm)

TY-FRL

2-1/4" DIA.

(57,2 mm)

1-1/2" (38,1 mm)

1-3/4" (44,5 mm)

MOUNTING

PLATE

1/8"

(3,2 mm)

2-7/8" DIA.

(73,0 mm)

1/2" (12,7 mm)

FIGURE 5

SERIES TY-FRL (TY3221) RECESSED PENDENT SPRINKLER ASSEMBLY

WITH TW0-PIECE 1/2 INCH TOTAL ADJUSTMENT

STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT

WRENCH

RECESS

FIGURE 6

W-TYPE 9 SPRINKLER

WRENCH

RECESS

PUSH WRENCH UP TO

ENSURE ENGAGEMENT

WITH SPRINKLER

WRENCHING AREA

FIGURE 7

W-TYPE 12 RECESSED

SPRINKLER WRENCH

TFP130

Page 5 of 6

TEFLON is trademark of The DuPont Corporation.

GLOBAL HEADQUARTERS | 1400 Pennbrook Parkway, Lansdale, PA 19446 | Telephone +1-215-362-0700

Ordering

Procedure

Contact your local distributor for avail-

ability. When placing an order, indi-

cate the full product name and Part

Number (P/N).

Sprinkler Assemblies with NPT

Thread Connections

Specify: Series TY-FRL (specify

SIN), (specify K-factor), (specify Up-

right, Pendent, or Recessed Pendent)

Sprinkler Quick Response, (specify)

temperature rating, (specify type of

ﬁnish), P/N (specify from Table B)

Recessed Escutcheon

Specify: Style 20 Recessed Escutch-

eon with (specify ﬁnish), P/N (specify)

1/2” (15 mm)

Style 20

Brass Plated....... P/N 56-705-2-010

1/2” (15 mm)

Style 20

Signal White (RAL9003)

.................P/N 56-705-4-010

1/2” (15 mm)

Style 20

Chrome Plated .....P/N 56-705-9-010

Sprinkler Wrench

Specify: W-Type 9 Sprinkler Wrench,

P/N 56-000-1-849.

Specify: W-Type 12 Sprinkler Wrench,

P/N 56-798-1- 001.

SIN

973 2.8K UPRIGHT (1/2”NPT) T Y1121

981 2.8K PENDENT (1/2”NPT) TY1221

974 5.6K UPRIGHT (1/2”NPT) TY3121

982 5.6K PENDENT (1/2”NPT) TY3221

174 8.0K UPRIGHT (1/2”NPT) T Y4121

172 8.0K PENDENT (1/2”NPT) T Y4 221

SPRINKLER

1NATURAL BRASS

9CHROME PLATED

TEMPERATURE

RATING

165 165°F (74°C)

212 212°F (100°C)

P/N 58 - XXX - X - XXX

TABLE B

SERIES TY-FRL PENDENT AND UPRIGHT SPRINKLERS

PART NUMBER SELECTION

TFP130

Page 6 of 6

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de riego de Tyco

Tyco

Tyco TFP MAX Manual de usuario

Tyco

Tyco EC-5 Series Manual de usuario

Tyco

Tyco TY-FRL-5.6 Series Manual de usuario

Tyco

Tyco ESFR-17 Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Tyco

Tyco RAVEN Institutional TY3281 Manual de usuario

Tyco

Tyco LFII Series Manual de usuario

Tyco

Tyco EC-5 Series Manual de usuario

Tyco

Tyco SW-20 Manual de usuario

Tyco

Tyco ESFR-17 Manual de usuario

Tyco

Tyco Rapidresponse LFII Series Instrucciones de funcionamiento y mantenimiento

Tyco

Tyco Issue D Quartzoid TY3191 Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Tyco

Tyco K17-231 Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Tyco

Tyco LFII Series Manual de usuario

Tyco

Tyco Rapidresponse LFII Series Manual de usuario

Tyco

Tyco ELO-231 Series Manual de usuario

Tyco

Tyco EC-25 Manual de usuario

Tyco

Tyco EC-11 Series Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Tyco

Tyco ESFR-14 Manual de usuario

Tyco

Tyco ESFR-17 Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Manuales populares de Sistema de riego de otras marcas

Hunter

Hunter Institutional Series Manual de usuario

Cellfast

Cellfast 52-305 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL A Manual de usuario

Oral Care Technologies

Oral Care Technologies Hydro Floss Manual de usuario

Reliable

Reliable F1-300 Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem F892 Manual de usuario

Netafim

Netafim NETBEAT Manual de usuario

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manual de usuario

Reliable

Reliable F4FR Manual de usuario

OpenSprinkler

OpenSprinkler OSPi Manual de usuario

EINHELL

EINHELL GE-WW 5537 E Manual de usuario

Valley

Valley Bender160 Manual de usuario

Reliable

Reliable F1FR42 Series Manual de usuario

Reliable

Reliable F1FR-300 Manual de usuario

Toro

Toro 730 Series Guía rápida

Eden

Eden 97063-EDAMZ Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Manual de usuario