Tyco F08 FIP Manual de usuario

FIRE FIGHTER’S GUIDE

1. SILENCING BELLS

Press “SILENCE” key once.

- ALL flashing red “ALM” LEDs will go steady

- Local Bells will be silenced

- The internal sounder will be silenced if no fault

condition exists.

-Any new alarm will cause the bells to ring again

and the appropriate zone alarm LED to flash.

2. RESETTING ALL ZONES IN ALARM

Press “SELECT” key, if required, until all green “SEL” LEDs are

OFF, then press “RESET” key once.

- ALL flashing or steady red “ALM” LEDs turn OFF.

SILENCE

- Zone(s) still in alarm will be indicated again.

3. ISOLATING ALL ZONES IN ALARM

Press “SELECT” key, if required, until all green “SEL” LEDs are

OFF, then press “ISOLATE” key once.

RESET

- ALL flashing red “ALM” LED indicators will go steady

and amber “ISO” LEDs will turn ON.

-DE-ISOLATING ZONE WILL RE-ACTIVATE BELLS

4. ISOLATING SELECTED ALARM ZONE

Press “SELECT” key until the required zone’s green “SEL” LED

is ON, then press “ISOLATE” key once.

- Amber “ISO” LED will turn ON.

-IF A FALSE ALARM, CALL THE MAINTENANCE

COMPANY RESPONSIBLE FOR THE FIRE ALARM

SYSTEM.

ISOLATE

3. RING SILENCED BELLS

Press “SELECT” key until a ZONE IN ALARM is SELECTED.

(Green “SEL” LED is ON)

If amber “ISO” LED is ON, press “ISOLATE” key ONCE.

If amber “ISO” LED is OFF, press “ISOLATE” key TWICE.

- Amber “ISO” LED indicator will be OFF.

ISOLATE

SELECT

- Bells are operated.

ISOLATE

SELECT

THIS PAGE INTENTIONALLY LEFT BLANK

F08 FIP

OPERATOR’S MANUAL

F08 PRODUCT MANUAL

DOCUMENT: LT0054 (A5 Bound)

DOCUMENT: LT0080 (A4 Loose)

Issue 3.05; 24 March 2006

- A P P R O V A L S -

F08 PANEL APPROVALS TO AUSTRALIAN STANDARDS AS1603.4 1987 AMDT 1 & 2

SSL LISTING NUMBER afp380

The F08 Fire Indicator Panel is manufactured for

Tyco Services Fire & Safety

47 Gilby Road

Mt Waverley

VIC 3149

AUSTRALIA

Tel : +61-3-9538 7220

Fax : +61-3-9538 7255

Information contained in this document is copyright, and shall not be reproduced in any form whatsoever,

or its contents disclosed to any third party, without the written consent of Tyco Services Fire & Safety (The

Company). Information contained in this document is believed to be accurate and reliable, however the

company reserves the right to change the content without prior notice.

F08 Operator's Manual Document No: LT0054

INSTALLATION DETAILS

3.W A R N I N G –

The F08 is approved to AS/NZS 3548 Class A. In a domestic environment it may cause

radio interference in which case the user may be required to take adequate measures.

For your reference please complete the following information on the F08 Fire Indicator Panel

supplied.

PANEL TYPE F08

PANEL SUPPLIED BY

PANEL SERIAL NUMBER

PANEL DATE OF MANUFACTURE

INSTALLED BY

AS INSTALLED DRAWING NUMBER ISSUE:

COMMISSIONED DATE

CONTRACT / JOB NUMBER

OWNER / ADDRESS

OWNERS REPRESENTATIVE

TELEPHONE B.H. A.H.

SERVICE COMPANY

SERVICE CONTACT

TELEPHONE B.H. A.H.

Page ii 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual

TABLE OF CONTENTS

INSTALLATION DETAILS ....................................................................................................ii

AMENDMENT LOG..............................................................................................................vi

1 SYSTEM DESCRIPTION.................................................................................................. 1-1

1.1 OVERVIEW....................................................................................................................1-2

1.2 DISPLAY PANEL .......................................................................................................... 1-4

1.3 COMMAND KEYS......................................................................................................... 1-7

2 SPECIFICATIONS............................................................................................................ 2-1

2.1 SYSTEM........................................................................................................................ 2-2

2.2 PHYSICAL..................................................................................................................... 2-3

2.3 ELECTRICAL ................................................................................................................ 2-4

2.4 INDICATORS................................................................................................................. 2-4

2.5 SWITCHES....................................................................................................................2-4

3 INTERPRETING THE DISPLAYS.................................................................................... 3-1

3.1 SYSTEM NORMAL ....................................................................................................... 3-2

3.2 RESPONDING TO ALARMS ........................................................................................ 3-2

3.3 DEALING WITH FAULTS ............................................................................................. 3-3

3.4 ZONE INDICATIONS..................................................................................................... 3-4

3.5 SYSTEM STATUS INDICATORS ................................................................................. 3-5

3.6 OUTPUT INDICATORS................................................................................................. 3-6

4 BRIGADE OPERATING FUNCTIONS............................................................................. 4-1

4.1 RESETTING ZONE(S) IN ALARM OR FAULT............................................................. 4-2

4.2 SILENCING ZONE(S) IN ALARM OR FAULT.............................................................. 4-3

4.3 ISOLATING ZONE(S) IN ALARM................................................................................. 4-4

5 SYSTEM OPERATING FUNCTIONS............................................................................... 5-1

5.1 SYSTEM TEST.............................................................................................................. 5-2

5.2 BATTERY TEST............................................................................................................ 5-3

5.3 OUTPUT ISOLATE/DE-ISOLATE................................................................................. 5-4

Issue 3.05 24 March 2006 Page iii

F08 Operator's Manual Document No: LT0054

5.4 ANCILLARY RELAY FAULT RESET ........................................................................... 5-5

5.5 OUTPUT TEST & MAPPING DISPLAY........................................................................ 5-6

6 ZONE OPERATING FUNCTIONS.................................................................................... 6-1

6.1 ZONE TEST...................................................................................................................6-2

6.2 ZONE ISOLATE/DE-ISOLATE...................................................................................... 6-4

6.3 AUTO-RESET MODE (One Person Detector-in-Situ Test)...................................... 6-5

7 PLACING INTO OPERATION.......................................................................................... 7-1

7.1 GENERAL .....................................................................................................................7-2

7.2 MAINS ISOLATE SWITCH............................................................................................ 7-2

7.3 POWER UP ................................................................................................................... 7-3

7.4 COMMISSIONING CHECKLIST ................................................................................... 7-3

8 SYSTEM MAINTENANCE & TROUBLE-SHOOTING ..................................................... 8-1

8.1 SYSTEM MAINTENANCE............................................................................................. 8-2

8.2 TROUBLE-SHOOTING ................................................................................................. 8-3

APPENDIX A – COMPATIBLE ACTUATING DEVICES….………………………………..... A-1

APPENDIX B – COMPATIBLE BATTERIES……………….…………………………………..

A-3

APPENDIX C – SYSTEM CONFIGURATION……………………………………………… ...A-4

Page iv 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual

AMENDMENT LOG

ISSUE DATE AMENDMENT ECN

04/05/92

Revised and upgraded from Document 696-002 (Issue

1 Amdt 1) to VIGILANT Document LT0054.

2.0

27/05/98

Converted to WORD format.

3.0

27/10/98

Modified for V3.00 software, 15V MCP and M614

detectors. New circuit delay types added.

Programmable mode for zone open collector outputs to

override zone isolate. 5 second reset time for new

M614 detector types.

2769

3.01

03/12/98

Appendix A Approved Detectors Revised.

ECS543

3.02

31/07/02

Prefix and Appendix A revised

3322

3.03

01/03/05

Appendix A – added 614CH, 614I & 614P

3635

3.04

28/10/05

Appendix A – added System Sensor detector 885WP-B

ECS1181

3.05

24/03/06

Appendix A – added 614T 3731

Issue 3.05 24 March 2006 Page v

F08 Operator's Manual Document No: LT0054

THIS PAGE LEFT INTENTIONALLY BLANK

Page vi 24 March 2006 Issue 3.05

Document No: LT0054 F08 Operator's Manual

System Description

1 SYSTEM DESCRIPTION

Issue 3.05 24 March 2006 Page 1-1

F08 Operator's Manual Document No: LT0054

System Description

1.1 OVERVIEW

The F08 Fire Indicator Panel (FIP) is a compact, self-contained fire indicator panel, which

performs the functions of the Control and Indicating Equipment (CIE), as specified by the

Australian Standard AS1603.4 Automatic Fire Detection and Alarm Systems.

It is microprocessor based and provides a maximum of eight detection zones using

approved compatible actuating devices. A general view of the F08 Fire Indicator Panel,

illustrating its various components, is shown in Figure 1.1.

The fire alarm system consists of fire detectors and/or manual call points installed in various

locations throughout the building, or area to be protected, linked to the F08 FIP.

When any detector or manual call point is operated, a signal is received by the FIP. The F08

panel reacts to the alarm condition as programmed, and may provide visual and audible

indications. Other signals to remote functions may also be generated. Examples include:

a) Mechanical ventilation plant shutdown

b) Local Alarm

c) Alarm to Fire Control Station.

The F08 fire indicating panel consists of:

a) A Wall-Mounting Cabinet

b) One Processor Main board, including Power Supply/Charger

c) One Display/Control Board.

The panel is a standard part that can be interchanged in the field. The door of the panel

contains display electronics and controls, whilst the rear of the cabinet contains processing

electronics, and input and output terminals.

The F08 FIP provides a range of programmable options. These are: disable unused circuits;

latching or non-latching circuits; ten types of circuit timing delays, including AVF and 1668

control; 'mapping' of zones to outputs; and ancillary output supervision.

NOTE: If your requirements have changed, the F08 FIP will require reprogramming,

so please consult your installation or service company.

The following F08 product manuals are available:

Volume 1, F08 Operator’s Manual, provides a complete guide to the operation, and

maintenance of the F08 Fire Indicator Panel, according to Australian Standards AS1603 Part

4. This manual is provided as standard with the F08 FIP. Part Numbers are LT0080 in A4

size, or LT0054 in A5, that will fit inside the F08 FIP.

Volume 2, F08 Technical Manual, provides complete technical details on the F08 system

and components, according to Australian Standards AS1603 Part 4, for servicing purposes.

Part Number is LT0081.

Volume 3, F08 Installation Manual, provides complete installation and programming

instructions for the F08 system. Part Number is LT0082.

Page 1-2 24 March 2006 Issue 3.05

Tabla de contenidos

Otros manuales de Sistema de riego de Tyco

Tyco

Tyco Rapidresponse LFII Series Manual de usuario

Tyco

Tyco TY-B Series Manual de usuario

Tyco

Tyco LFII Series Guía

Tyco

Tyco EC-HS Manual de usuario

Tyco

Tyco RapidResponse SIN TY4334 Manual de instrucciones

Tyco

Tyco DS-2 Series Manual de usuario

Tyco

Tyco ESFR-34 Manual de usuario

Tyco

Tyco RAPID RESPONSE Series Manual de usuario

Tyco

Tyco F950 Manual de usuario

Tyco

Tyco TY-FRL Series Manual de usuario

Tyco

Tyco Ultra K17 Manual de usuario

Tyco

Tyco TY-L Series Manual de usuario

Tyco

Tyco TY-FRB Series Manual de usuario

Tyco

Tyco G2 Manual de usuario

Tyco

Tyco TY-FRB Series Manual de usuario

Tyco

Tyco TY-FRL Series Manual de usuario

Tyco

Tyco TY-FRB Series Manual de usuario

Tyco

Tyco TY-FRL Series Manual de usuario

Tyco

Tyco ESFR-1 Instrucciones de funcionamiento y mantenimiento

Tyco

Tyco ILLUSION TY5521 Manual de usuario

Tyco

Tyco ESFR-14 Manual de usuario

Tyco

Tyco ELO-231B Series Manual de usuario

Tyco

Tyco ESFR-14 Manual de usuario

Tyco

Tyco Rapidresponse LFII Series Manual de usuario

Manuales populares de Sistema de riego de otras marcas

Hunter

Hunter Institutional Series Manual de usuario

Cellfast

Cellfast 52-305 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL A Manual de usuario

Oral Care Technologies

Oral Care Technologies Hydro Floss Manual de usuario

Reliable

Reliable F1-300 Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem F892 Manual de usuario

Netafim

Netafim NETBEAT Manual de usuario

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manual de usuario

Reliable

Reliable F4FR Manual de usuario

OpenSprinkler

OpenSprinkler OSPi Manual de usuario

EINHELL

EINHELL GE-WW 5537 E Manual de usuario

Valley

Valley Bender160 Manual de usuario

Reliable

Reliable F1FR42 Series Manual de usuario

Reliable

Reliable F1FR-300 Manual de usuario

Toro

Toro 730 Series Guía rápida

Eden

Eden 97063-EDAMZ Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 Manual de usuario