Tyco Fire Product CENTRAL H17/32 Manual de usuario

*For specific listing requirements see the appropriate

information contained in this brochure.

1-98

Model: H17⁄32

Style: Horizontal Sidewall and

Recessed Horizontal Sidewall

Escutcheon: Model GB 3⁄4" Recessed

Cup/Escutcheon

Assembly

Note: For the recessed version, only

the Model GB

⁄

" Recessed

Cup/Escutcheon Assembly may

be used. Substitution of other

“recessed” escutcheons may

impair the operating sensitivity

and distribution pattern.

Orifice Size: 17⁄32" (13.5 mm)

K Factor: 8.1 (116.8 metric)

Thread Size: 3⁄4" (20 mm) N.P.T.

Temp. Rating & Frame Arm Color:

135°F/57°CUncolored

145°F/63°CUncolored

165°F/74°CUncolored

Approvals: U.L., U.L.C., M.E.A.

(Cal. No. 375-75-SA)

Maximum Working Pressure:

175 psi (12.1 bar)

Factory Hydro Test:

100% at 500 psi (34.5 bar)

StandardFinishes:

Sprinkler: brass, chrome plated

Escutcheon: brass, chrome plated

Length: 215⁄16" (74.6 mm)

Width: 15⁄8" (41.3 mm)

Frame Arms: 17⁄16" (36.5 mm)

Deflector: 15⁄8" (41.3 mm)

Weight: 4.2 oz. (119 g)

Technical

Data

The Model H17⁄32 Horizontal

Sidewall and Recessed Sidewall

Automatic Sprinklers are intended for

installation in accordance with current

NFPA 13 and their Extended

Coverage Listing* parameters. They

are ideally suited for use in churches,

clubs, schools, hospitals, offices,

restaurants, hotels, auditoriums and

similar light hazard occupancies.

They are available in one orifice

size, three temperature ratings and

two standard finishes.

Operation: A fusible alloy is sealed

into a bronze center strut by a

stainless steel ball. When the alloy

melts at its rated temperature, the ball

is forced upward into the center strut

releasing the two ejectors and

operating the sprinkler. Unlike most

other sprinkler designs, the alloy is

not exposed to atmospheric

conditions that could affect its proper

functioning. It is also less susceptible

to mechanical damage since there

are no protruding elements extending

beyond the sprinkler frame.

H17⁄32

H17⁄32 Sidewall and

Recessed Sidewall

ExtendedCoverage 16' x 20' (4.9m x 6.1m) max.

Horizontal SidewallAutomatic Sprinkler

Manufactured by: Central Sprinkler Company

451 North Cannon Avenue, Lansdale, Pennsylvania 19446

No. 2-13.0

Product

Description

17⁄32"(13.5mm)

Orifice

Sidewalland

Recessed

Sidewall

Sprinkler

OBSOLETE

2 15/16"

11/16" 2 1/4"

1" 1 7/16"

Face of 1" x 3/4"

Reducing Coupling

2 1/4" Max.

2" Min.

Finished Wall

1/2" ±1/4" Field

Adjustment

Deflector to Ceiling

Distance

(see table on page 3)

GB 3/4" Recessed

Cup/Escutcheon Assembly

Figure 1

Model H17⁄32 Recessed Horizontal Sidewall Sprinkler

Figure 2

Model H17⁄32 Horizontal Sidewall Sprinkler

(74.6 mm)

(17.5 mm) (57.2 mm)

(25.4mm) (36.5 mm)

(57.2 mm)

(50.8 mm)

(12.7mm 6.4 mm)

OBSOLETE

Technical

Data

*Teflon is a trademark of the DuPont Corp.

Design Requirements — Extended Coverage Applications – Light Hazard

Coverage Area Minimum Minimum Distance Temperature

Width Throw Flow Pressure Below Ceiling Rating

Ft. (m) Ft. (m) gpm (lpm) psi (bar) (mm)

F (

*16 (4.9) 16 (4.9) 29 (109.9) 12.8 (0.9) 4" - 6" (101-152) 135 (57), 145 (63), 165 (74)

*16 (4.9) 16 (4.9) 32 (121.3) 15.6 (1.1) 4" - 12" (101-304) 135 (57), 145 (63), 165 (74)

16 (4.9) 18 (5.5) 36 (136.4) 19.8 (1.4) 4" - 6" (101-152) 135 (57), 145 (63)

16 (4.9) 20 (6.1) 36 (136.4) 19.8 (1.4) 4" - 6" (101-152) 135 (57), 145 (63)

Installation

The Model H17⁄32 Sidewall and

Recessed Sidewall Sprinkler must be

installed according to current NFPA

13 Standards. Deviations from these

requirements and standards or any

alteration to the sprinkler itself will

void any warranty made by Central

Sprinkler Company. In addition,

installation must also meet local

government provisions, codes and

standards as applicable.

The system piping must be

properly sized to ensure the minimum

required flow rate at the sprinkler.

Check for the proper model, style,

orifice size and temperature rating

prior to installation. Install sprinklers

after the piping is in place to avoid

mechanical damage. Replace any

damaged units. Wet pipe systems

must be protected from freezing; refer

to the Central Bulletins on the Model

H-1 Dry Horizontal Sidewall

Sprinklers for use in dry pipe sprinkler

installations.

Upon completion of the installation,

the system must be tested per

recognized standards.

In the event of a thread leak,

remove the unit, apply new pipe joint

compound or tape and reinstall.

CAUTION: Do not wrench or turn

the deflector, as this action may

damage the sprinkler and cause it

to leak under pressure.

Special care must be taken when

installing sprinklers with a CPVC

system. Sprinklers must be installed

after the CPVC manufacturer's

recommended setting time for the

primer and cement to ensure that

neither accumulates within the

sprinkler.

Special care must be taken when

installing with a copper system.

Sprinklers must be installed only after

the inside of the sprinkler nipple and

associated fittings have been wire

brushed to remove any flux. Residual

flux can cause corrosion and in

extreme cases can impair proper

sprinkleroperation.

Installation Sequence

Step 1. The unit must be installed in

the horizontal position.

Step 2. Use only a non-hardening

pipe joint compound or Teflon* tape.

Apply only to the male threads.

Step 3. Hand tighten the sprinkler

into the fitting. Then use a Central

Sprinkler H & HF wrench to tighten

the unit into the fitting. A leak-tight

joint requires only 7-14 ft-lbs (9.5 - 19.0

Nm). of torque; a tangential force of 14-

28 lbs (62.3 - 124.5 N). delivered through a

6" (150 mm) handle will deliver adequate

torque. Torque levels over 21 ft-lbs

(28.6 Nm) may distort the orifice seal,

resulting in leakage.

Sprinklers must be handled

carefully. They must not be

transported or stored where ambient

temperatures may exceed 100oF/

38oC. For best results, store them in

a dry, cool location in the original

Care &

Maintenance

The Model H17⁄32 Sidewall and Recessed Sidewall Sprinklers are U.L. Listed for Extended Coverage applications in

light hazard occupancies only. For non-recessed versions, the distance away from the wall is per NFPA 13.

*Use these design requirements for spacings less than 16' x 16' (4.9m x 4.9m).

H & HF Sprinkler Wrench

(Part #1108)

OBSOLETE

Printed in U.S.A.

maintain the protection level.

Do not attempt to replace sprinklers

without first removing the fire

protection system from service. Be

certain to secure permission from all

Authorities Having Jurisdiction, and

notify all personnel who may be

affected during system shutdown. A

fire watch during maintenance periods

is a recommended precaution.

To remove the system from

service mode, first refer to the system

operating guide and valve instruction.

Drain water and relieve pressure in

the pipes. Remove the existing unit

and install the replacement, using

only the special sprinkler wrench. Be

certain to match model, style, orifice,

and temperature rating.

A fire protection system that has

been shut off after an activation

should be returned to service

immediately. Inspect the entire

system for damage and replace or

repair as necessary. Sprinklers that

did not operate, but were subjected to

corrosive elements of combustion or

excessive temperatures should be

inspected and replaced if needed.

The

Authority Having Jurisdiction

will

detail minimum replacement

requirements and regulations.

Guarantee: Central Sprinkler

Company will repair and/or replace

any products found to be defective in

material or workmanship within a

period of one year from the date of

shipment. Please refer to the current

Price List for further details of the

warranty.

Ordering

Information

Ordering Information: When

placing an order, indicate the full

product name. Please specify the

quantity, model, style, orifice size,

temperature rating, type of finish and

sprinkler wrench.

Availability and Service: Central

sprinklers, valves, accessories, and

other products are available

throughout the U.S. and Canada; and

internationally through a network of

Central Sprinkler distribution centers.

You may write directly to Central

Sprinkler Company or call (215) 362-

0700 for the distributor nearest you.

Patents: Patents are pending.

Conversion Table:

1 inch = 25.400 mm

1 foot = 0.3048 m

1 pound = 0.4536 kg

1 foot pound = 1.36 Nm

1 psi = 6.895 kpa

= 0.0689 bar

= 0.0703 kg/cm2

1 U.S. gallon = 3.785 dm3

= 3.785 liters

Conversions are approximate.

shippingpackage.

Do not install sprinklers that have

been dropped or visibly damaged.

Sprinklers must never be painted,

coated, plated or altered in any other

way from manufactured condition or

they may not function properly. Any

sprinklers altered in such manner

must be replaced.

The owner is responsible for the

proper operating condition of all fire

protection devices and accessories.

The NFPA Standard 25 entitled,

“Inspection, Testing and Maintenance

of Water-Based Fire Protection

Systems”

, contains guidelines and

minimummaintenance requirements.

Furthermore, the local

Authority

Having Jurisdiction

may have

additional regulations and

requirements for maintenance,

testing, and inspection that must be

obeyed.

It is recommended that sprinkler

systems be inspected regularly by a

qualified inspection service. Length of

time between such inspections can

vary due to accessibility, ambient

atmosphere, water supply and site

activity.

Do not attempt to reassemble or

otherwise reuse a sprinkler that has

operated. Replace any sprinkler

exhibiting corrosion or damage.

Always use new sprinklers of the

same type and temperature rating as

replacements.

Because the discharge pattern is

critical to protection of life and

property, nothing should be hung or

attached to the sprinkler unit that

would disrupt the pattern. Such

obstructions must be removed. In the

event that construction has altered

the original configuration, additional

sprinklers should be installed to

H17⁄32.2

Central Sprinkler Company

451 N. Cannon Avenue, Lansdale, PA 19446

Phone (215) 362-0700

FAX (215) 362-5385

OBSOLETE

Otros manuales de Sistema de riego de Tyco Fire Product

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-GB QR Dry Pendent Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem DS-1 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL A Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231 BV Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Attic BB1-17/32 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL TY-B Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL H-1 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-231TM Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL BV-R1 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Quasar Q Manual de usuario

Tyco Fire Product

Tyco Fire Product Star SG300 Manual de usuario

Tyco Fire Product

Tyco Fire Product RAPID RESPONSE LFII Series Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL DS-2 Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Galaxy SGQR Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem TY-B Series Manual de usuario

Tyco Fire Product

Tyco Fire Product STAR S160E Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem RFII Series Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL Omega HEC-12EC PRO Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Galaxy SG-RES Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL ELO-16 GB Manual de usuario

Tyco Fire Product

Tyco Fire Product Star PH-2 Manual de usuario

Tyco Fire Product

Tyco Fire Product CENTRAL TFP1 Manual de usuario

Tyco Fire Product

Tyco Fire Product Gem TY-B Manual de usuario

Tyco Fire Product

Tyco Fire Product Star Luminous S170 Manual de usuario

Manuales populares de Sistema de riego de otras marcas

Hunter

Hunter Institutional Series Manual de usuario

Cellfast

Cellfast 52-305 Manual de usuario

Oral Care Technologies

Oral Care Technologies Hydro Floss Manual de usuario

Reliable

Reliable F1-300 Manual de usuario

Netafim

Netafim NETBEAT Manual de usuario

Irrigation-Mart

Irrigation-Mart KIT-GK100-RV-B Manual de usuario

Tyco

Tyco CC3 Manual de usuario

Reliable

Reliable F4FR Manual de usuario

OpenSprinkler

OpenSprinkler OSPi Manual de usuario

EINHELL

EINHELL GE-WW 5537 E Manual de usuario

Valley

Valley Bender160 Manual de usuario

Reliable

Reliable F1FR42 Series Manual de usuario

Reliable

Reliable F1FR-300 Manual de usuario

Toro

Toro 730 Series Guía rápida

Eden

Eden 97063-EDAMZ Manual de usuario

Tyco

Tyco TY-L Series Manual de usuario

Johnson Controls

Johnson Controls tyco ESFR-17 Manual de usuario

Victaulic

Victaulic VicFlex I-VICFLEX.AQC-U Manual de usuario