TYAN TRINITY I845 Manual de usuario

http://www.tyan.com

Trinity i845

S2090

User’s Manual

Revision 1.00

reproduced or translated without prior written consent from Tyan Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

Tyan, Trinity S2090 are trademarks of Tyan Computer Corporation.

Intel, Intel Pentium, i845, combinations thereof are trademarks of Intel Corporation.

Award BIOS is a trademark of Phoenix Software.

Microsoft, Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Micronics is a trademark of Micronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Iomega, Zip are registered trademarks of Iomega Corporation.

Information contained in this document is furnished by Tyan Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. Tyan assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of Tyan products including

liability or warranties relating to fitness for a particular purpose or merchantability. Tyan retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will Tyan be held liable for any direct or indirect, incidental or consequential damage, loss

of use, loss of data or other malady resulting from errors or inaccuracies of information contained in

this document.

http://www.tyan.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.1 Congratulations

1.2 Hardware Specifications

1.3 Software Specifications

Chapter 2: Board Installation

2.1 Front Panel Connector

2.2 CMOS Reset

2.3 FAN Connectors

2.4 Thermal Trip Connector

2.5 Boot Block Connector

2.6 Processor HOT LED

2.7 Hard Drive LED

2.8 Hardware Reset Switch Connector

2.9 BIOS Flash Utility

2.10 Mounting the Motherboard

2.11 Installing Memory

2.12 Installing the CPU and Cooling Fan

2.13 Connecting IDE and Floppy Drives

2.14 Installing Add-in Cards

2.15 Connecting PS/2, USB, Serial

Devices

2.16 Connecting the power supply

2.17 You’re done!

Chapter 3: BIOS Setup

3.1 Standard CMOS Features

3.2 Advanced BIOS Features

3.3 Advanced Chipset Features

3.4 Integrated Peripherals

3.5 Power Management Setup

3.6 PnP/PCI Configuration

3.7 Frequency/Voltage Control

Chapter 4: Installing the Hard Drives

Chapter 5: System Resources

5.1 Beep Codes

5.2 Flash Utility

Appendix I: Glossary

Technical Support

……………………………………………..Page 4

……………………………………………..Page 5

……………………………………………..Page 6

……………………………………………..Page 8

……………………………………………..Page 9

…………………………………………….Page 10

……………………………………………Page 11

……………………………………………Page 12

……………………………………………Page 13

……………………………………………Page 14

……………………………………………Page 15

……………………………………………Page 16

……………………………………………Page 17

……………………………………………Page 18

……………………………………………Page 19

……………………………………………Page 21

……………………………………………Page 23

……………………………………………Page 24

……………………………………………Page 25

……………………………………………Page 26

……………………………………………Page 27

……………………………………………Page 28

……………………………………………Page 29

……………………………………………Page 30

……………………………………………Page 31

……………………………………………Page 32

……………………………………………Page 33

……………………………………………Page 35

……………………………………………Page 40

http://www.tyan.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Trinity i845 motherboard

1x Pentium 4 Heatsink Mounting Kit

1x 34-Pin floppy drive cable

1x Ultra-DMA-100/66/33 IDE cable

1x Trinity i845 user’s manual

1x Tyan driver CD

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

http://www.tyan.com

Chapter 1: Introduction

1.1 Congratulations!

You are now the owner of the Tyan Trinity i845 motherboard, the most reliable, high performance

motherboard for Pentium 4 processing. The Trinity i845 supports the latest Pentium 4 processors

as well as all the latest peripherals. It’s a high performance board targeted mainly at enthusiasts,

power users and workstations. The Trinity i845 also provides the easiest upgrade path for existing

PC users who don’t want the hassle of purchasing a new chassis and power supply. Use an

existing ATX power supply and the Trinity i845 will support it out of the box. *Please see Tyan’s

website for updates and information concerning CPU information and support:

http://www.tyan.com

The Trinity i845 leaves plenty of room for upgrades but also includes all the necessary

components to get you started. Built into the Trinity i845 is a 100Mbit Ethernet solution provided

by Intel for quick network setups and blazing fast transfer speeds.

All six PCI slots are free and open for upgrades. Adding to the ease of expansion and support is

the use of current industry standard PC133 SDRAM. Boasting high speeds at low costs, the

Trinity i845 is the ideal platform for the Pentium 4.

Remember to visit Tyan’s Website at http://www.tyan.com. There you can find information on all of

Tyan’s products with FAQs, distributors list and BIOS setting explainations.

1.2 Hardware Specifications

Processor

•Single PGA478 ZIF sockets

•Supports one Intel Pentium 4 (478pin)

processor

•SDR bus support for 133MHz

•Integrated VRM

•Auto configure Clock Multiplier

•Auto detect CPU core voltage

Chipset

•Intel i845 (Brookdale) Chipset

•Intel ICH 2

•Onboard 82562ET 10/100Mbit LAN (future

option)

•LPC I/O Winbond with hardware monitoring

built in.

Memory

•Three 3.3v 168-pin DIMM sockets

•Supports up to 3GB of

unregistered/unbuffered PC133 SDRAM

Expansion Slots

•1 AGP (1.5v, 4x)

•6 32-bit/33MHz PCI bus mastered slots

Hardware Monitoring

•Winbond W83782D hardware monitoring

ASIC

•CPU Temp, voltage and fan monitoring

BIOS

•Award 4Mb BIOS Flash ROM (FWH)

•Fully Plug-and-Play

•APM 1.2/ACPI 1.0/PC99 compliant

•DMI 2.0 compliant

•Soft Power Down

•Multiple boot options

•Instant PC (Suspend to RAM support)

•3-pin wake on LAN header (requires ATX

standby 5v/750mA power supply)

•2-pin chassis intrusion header.

Form Factor

•ATX footprint (12” x 9.6”)

•ATX 2.1 with 30A on 5v line Power supply

required

•One 20-pin ATX power connector

•Stacked USB (two) ports

•Stacked keyboard and mouse ports

http://www.tyan.com

Integrated PCI IDE

•Two 40-pin IDE connectors for up to 4

devices

•PIO mode 3, 4, UltraDMA 33/66/100 support

•ATAPI HDD CDROM and LS-120 support

Integrated I/O

•One floppy connector supports up to two

drives

•Two 9-pin 16550-based serial ports

•One 25-pin SPP/ECP/EPP parallel port

•One IR Tx/Rx header

•2 USB ports

•PS/2 keyboard and mouse ports

Regulatory

•FCC DoC (declaration of Conformity)

•European Community of CE (declaration of

Conformity)

1.3 Software Specifications

OS Windows 9x/ME/NT/2000

http://www.tyan.com

Chapter 2: Board Installation

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Trinity i845

matches the ATX system board specifications. Your chassis should support a standard ATX

motherboard form factor.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information which will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch the power supply.

For the safest conditions, Tyan recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board.

(3) Avoid touching the motherboard components, IC chips, connectors, and leads.

(4) Avoid touching memory module contacts and IC chips

(5) Place the motherboard on a grounded antistatic surface or on the antistatic bag from

which it came in.

Having reviewed the precautions above, the next step is to take the motherboard out of the

cardboard box and static bag, hold it by its edges and place it on a grounded antistatic surface,

component side up. Inspect the board for damage.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.tyan.com

2.1 Front Panel Connector (J20)

Your chassis will usually come with connectors to install onto the motherboard, such as HDD and

Power LEDs. The Front Panel Connector (J80) has been implemented for such purposes.

* optional feature available on some Trinity i845 models

J20

Infrared

(IrDA)

HM_INTR

IR TX

RST

SW HDD

LED

GND

IR RX

VCC

GND

VCC+

GND

Slp LED+

Pwr LED+

PWR

SW PWR

LED

Chassis Intrusion (pins 17+18)*

http://www.tyan.com

2.2 CMOS Reset (JP1)

If you have been locked out of your system because you forgot your password, or set the CMOS

incorrectly, or have just finished flashing your BIOS, you will need to reset the CMOS. The

instructions are as follows:

1. Power off the system

2. Close pins 2-3 on JP1

3. Wait about three seconds

4. Close pins 1-2 on JP1, then power on the system again

By following this procedure, you will erase your password and reset the CMOS. The location of

JP1 is shown in the diagram below.

JP1

CLOSE 1-2

CLOSE 2-3

Normal

Clear CMOS

* default is CLOSE 1-2

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de TYAN

TYAN

TYAN TOMCAT I915 Manual de usuario

TYAN

TYAN S8226 Manual de usuario

TYAN

TYAN THUNDER LE-T Manual de usuario

TYAN

TYAN TOMCAT I875PR Manual de usuario

TYAN

TYAN TOMCAT K8SH Manual de usuario

TYAN

TYAN Thunder n6550EX Manual de usuario

TYAN

TYAN THUNDER TOMCAT H1000E Manual de usuario

TYAN

TYAN InterServe 90 Manual de usuario

TYAN

TYAN TITAN-PRO AT Manual de usuario

TYAN

TYAN S5539 Manual de usuario

TYAN

TYAN S5533 Manual de usuario

TYAN

TYAN TITAN TURBO AT-2 Manual de usuario

TYAN

TYAN TIGER 100 Manual de usuario

TYAN

TYAN S7012 Manual de usuario

TYAN

TYAN S8238 Manual de usuario

TYAN

TYAN S5102 Manual de usuario

TYAN

TYAN S8020 Manual de usuario

TYAN

TYAN S2054 Manual de usuario

TYAN

TYAN TIGER K8W Manual de usuario

TYAN

TYAN TSUNAMI ATX Manual de usuario

TYAN

TYAN THUNDER LE S2510 Manual de usuario

TYAN

TYAN S7082 Manual de usuario

TYAN

TYAN TOMCAT I815EF Manual de usuario

TYAN

TYAN S7050 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario