TYAN THUNDER I7500 Manual de usuario

http://www.TYAN.com

Thunder i7500 ///

S2720

Revision 2.01

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Thunder i7500 S2720 are trademarks of TYAN Computer Corporation.

Intel, Xeon, and combinations thereof are trademarks of Intel Corporation.

AMI, AMIBIOS are trademarks of AMI Software Inc.

Microsoft, Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

http://www.TYAN.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.1 Congratulations

1.2 Hardware Specifications

1.3 Software Specifications

Chapter 2: Board Installation

2.0 Board

2.1 Board Jumpers, LEDs, & Fans

2.2 Jumper Legend

2.3 LED Information

2.4 Fan Header Information

2.5 PCI Setup

2.6 Mounting the Motherboard

2.7 Installing the Memory

2.8 Installing the Processors & Heatsinks

2.9 Attaching Drive Cables

2.10 Installing Add-In cards

2.11 Connecting External Devices

2.12 Installing the Power Supply

2.13 Finishing up

Chapter 3: BIOS

3.1 Main Setup

3.2 Advanced Settings

3.3 IDE Configuration

3.4 Floppy Configuration

3.5 Boot Settings Configuration

3.6 Super IO Configuration

3.7 Onboard Device Configuration

3.8 USB Configuration

3.9 PCIPnP

3.10 Chipset

3.11 CPU Configuration

3.12 North Bridge Configuration

3.13 ICH3 Chipset Configuration

3.14 Intel PCI-64 Hub Configuration

3.15 ACPI

3.16 ACPI Advanced

3.17 Boot

3.18 Security

3.19 Exit

Chapter 4: Diagnostics

4.1 Hardware Monitor Information

4.2 Beep Codes

4.3 Flash Utility

Appendix I: Onboard LAN LED Color Def.

Appendix II: Glossary

Technical Support

……………………………………………..Page 3

……………………………………………..Page 4

……………………………………………..Page 5

……………………………………………..Page 6

……………………………………………..Page 7

……………………………………………..Page 8

……………………………………………..Page 9

…………………………………………… Page 11

…………………………………………… Page 12

…………………………………………… Page 13

…………………………………………… Page 14

…………………………………………… Page 17

…………………………………………… Page 20

…………………………………………… Page 22

…………………………………………… Page 23

……………………………………………Page 23

…………………………………………… Page 24

……………………………………………Page 25

……………………………………………Page 27

……………………………………………Page 28

……………………………………………Page 29

……………………………………………Page 30

……………………………………………Page 31

……………………………………………Page 32

……………………………………………Page 33

……………………………………………Page 35

……………………………………………Page 36

……………………………………………Page 37

……………………………………………Page 42

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder i7500 motherboard

1x 34-Pin floppy drive cable

1x Ultra160/320 LVD SCSI cable (if optional SCSI included)

1x Ultra-DMA-100/66/33 IDE cable

1x Thunder i7500 user’s manual

1x TYAN driver CD

1x Adaptec Ultra160/Ultra320 SCSI driver diskette (if optional SCSI included)

1x I/O shield with 2 LAN ports

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

http://www.TYAN.com

Chapter 1: Introduction

1.1 –Congratulations!

You’re now the owner of the most advanced dual Intel processor solution –the Thunder i7500.

Based on Intel’s E7500 chipset, the Thunder i7500 continues to carry the strong Thunder line and

leaves little to be desired. Never leaving anything behind, the Thunder i7500 is Hyper-Threading

ready –fully supporting Hyper-Threading enabled Xeons. This means the Thunder i7500 comes

ready to meet networking, storage, and video demands right out of the box. All your networking

needs are handled with ease by both the onboard 10/100Mbps and 1Gbps network ports.

Storage support is flexible and speedy with optional dual channel Ultra320 SCSI or Ultra160

SCSI. With onboard video and support for unprecedented remote management, the Thunder

i7500 is one of the most compelling business solutions available.

The Thunder i7500 supports up to 12GB of Registered ECC PC2100/1600 DDR SDRAM, Xeon

processors 2GHz and beyond, and supports two 133MHz/100M/66Hz PCI-X slots, two

66MHz/33MHz PCI-X slots and one 32-bit/33MHz slot.

Remember to visit TYAN’s Website at http://www.tyan.com. There you can find information on all

of TYAN’s products with FAQs, distributors list and BIOS setting explanations.

1.2 –Hardware Specifications

Processor

• Dual PGA603 ZIF sockets

• Supports up to two Intel Xeon 512 Processors

• Onboard VRM (VRM 9.1 spec)

• Front-Side Bus support for 400MHz

Chipset

• Intel E7500 chipset

• MCH + ICH3 + P64H2 + FWH

• P64H2 supports two PCI-X busses

• Winbond 83627HF Super I/O ASIC

Memory

• Six 184-pin 2.5v DDR DIMM sockets

• Supports up to 12GB of Registered

PC1600/2100* DDR

memory

• Also supports ECC memory modules

Expansion Slots

• Two 64-bit 100/66/33MHz (3.3-volt) PCI-X

slots

• Two 64-bit 66/33MHz (3.3-volt) PCI-X slots

• One 32-bit 33MHz (5-volt) PCI slot

• Total of five usable slots

*The Thunder i7500 supports both PC2100

and PC1600 but Intel’s E7500 chipset will

only operate at PC1600.

Integrated SCSI (manufacturing option)

• Adaptec AIC –7899W

• 160 MB/sec maximum data throughput per

channel

• ** 320 MB/sec maximum data throughput per

channelavailable withAdaptec AIC –7902

option

• Supports up to 15 LVD SCSI devices per

channel

• Supports Adaptec Zero-Channel RAID (ZCR)

technology in PCI-X slot 2

Integrated 2D/3D Graphics

• ATI RAGE XL graphics controller

• 8MB (SDRAM)

• Standard 15-pin analog VGA port

Server Management Daughtercard (option)

• Q-Logic Zircon Baseboard Management

Controller (BMC)

• I2C and IPMB

• Supports the Intelligent Platform Management

Interface (IPMI)

http://www.TYAN.com

Integrated PCI IDE

• Dual-channel master mode

• Supports up to four Enhanced IDE devices

• Support for ATA-100/66/33 IDE and ATAPI

compliant devices

Integrated I/O

• One floppy connector supports up to two

drives

• Two 9-pin 16550-based serial ports

• One 25-pin SPP/ECP/EPP parallel port

• PS/2 keyboard and mouse ports

1.3 Software Specifications

Hyper Threading Support In:

Win2K Server

Win2K Advanced Server

XP Pro

Linux (Kernel 2.4.18)

NT 4.0 Server

TYAN reserves the right to add support or

discontinue support for any OS with or

withoutnotice.

HardwareMonitoring

• Winbond W83782D hardware monitoring

ASIC

• CPU temperature/voltage monitoring

• Chassis intrusion header

• 3 fan headers monitored and controlled by

W83782D

• 3 fan headers monitored by Super I/O

• 5 fan headers unmonitored

Total fan headers = 11

Total monitored headers = 6

BIOS

• AMI BIOS on 4Mbit/8Mbit Flash ROM

• Auto-configuration of IDE hard drive types

• Multiple boot options

Form Factor

• SSI EEB v3.0 footprint (12" x 13")

• EPS12V power connectors (24-pin and 8-pin)

• Stacked parallel (one), serial (one) and VGA

(one) ports

• Stacked USB (two) ports

• LAN (two) ports

• Stacked keyboard and mouse ports

Regulatory

• FCC DoC (Declaration of Conformity)

• European CE (Declaration of Conformity)

http://www.TYAN.com

Chapter 2: Board Installation

WARNING: The Thunder i7500 only supports

EPS12V power supplies and will not operate with

other types. Refer to section 2.12 for instructions on

installing EPS12V power supplies. DO NOT use

ATX 2.x, ATX12V and dual AMD power supplies as

they will damage the board and void your warranty.

Only EEB V3.0 form factor chassis is supported.

Other form factors may short the board because the

installation studs are in different locations than

ones required by the Thunder i7500.

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Thunder i7500

matches the SSI system board specifications. Your chassis should support a standard SSI

motherboardform factor.

How to install our products right…the first time

The first thing you should do is read this user’s manual. It contains important information which will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch the power supply.

For the safest conditions, TYAN recommends wearing a static safetywriststrap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board.

(3) Avoid touching the motherboard components, IC chips, connectors, and leads.

(4) Avoid touching memory module contacts and IC chips

(5) Place the motherboard on a grounded antistatic surface or on the antistatic bag from

which it came in.

Having reviewed the precautions above, the next step is to take the motherboard out of the

cardboard box and static bag, hold it by its edges and place it on a grounded antistatic surface,

component side up. Inspect the board for damage.

The following pages will detail for you on how to install your motherboard into your chassis, install

processor(s), memory, hard drive and floppy cables/drives and heatsinks.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.TYAN.com

2.0 –Board

The following is an image of the S2720 Thunder i7500.

The above photograph is only a representation of the actual board. Because boards tend to

be updated and go through different revisions, certain components may change and or be

repositioned. The picture above may or may not look exactly like the board you received.

The following page will detail vital components of this board.

http://www.TYAN.com

2.1 –Board Jumpers, LEDs, and Fans

The above jumper schematic diagram is representative of the latest board revision

available at the time of this manual’s publishing. The board you have received may or may

not be like the above diagram.

IMPORTANT NOTE:

Fan locations as labeled on some revisions of the motherboard may be incorrect. It is highly

recommended if you intend to monitor fans, that you use the information in this manual for

accuracy. If you found the addendum in your package you absolutely will need to follow the

manual for accurate location and function of fan headers.

http://www.TYAN.com

2.2 Jumper Legend

* WOL is only supported by LAN1 (82550, 10/100 Mbps).

Jumper OFF –open (without pin)

Jumper ON –closed (with pin)

CMOS Reset (J21)

Clear CMOS

Normal

You can reset the CMOS settings in case an incorrect setting causes system

instability or you have forgotten your system/setup password or have just flashed

your BIOS by using these jumpers.

-Power off system, disconnect power supply from motherboard

-Set jumper J21 to Clear CMOS

-Wait about 5 seconds Set jumper J21 to Normal

PCI-X Force 100MHz (J44)

Normal

Force 100MHz

Jumper open = Card dependent, will run at PCI-X capability of card inserted in

slots A1 and A2 (3 and 4 on silkscreen).

Jumper closed = Force PCI-X 100Mhz.

Jumper Function

J21

J22

J34

J38 *

J40

J41

J42

J43

J44

J49

J50

J51

J53

J55

Clear CMOS

External speaker header

Serial port internal header (Com 2)

Wake On LAN

Front Panel connector

Hard drive external activity LED

SMDC connector (Server Management daughter card)

I2C bus connector

PCI-X Force 100Mhz

Hyper Threading

USB internal port #3

USB internal port #4

Intel GbE 82544GC 4 pin external LAN activity/link

LED header

Intel 82550 4 pin external LAN activity/link LED

header

http://www.TYAN.com

Hyper-Threading (J49)

Normal

Hyper

Threading

Disabled

Jumper open = BIOS controls Hyper-Threading.

Jumper closed = Hyper -Threading disabled no matter what the BIOS setting

is.

Front Panel Connector (J40)

Your chassis will usually come with connectors to install onto the motherboard, such as HD and

Power LEDs. The Front Panel Connector (J40) has been implemented for such purposes.

Otros manuales para THUNDER I7500

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Placa madre de TYAN

TYAN

TYAN TOMCAT I915 Manual de usuario

TYAN

TYAN S5512 Manual de usuario

TYAN

TYAN Tiger K8WE Manual de usuario

TYAN

TYAN Tempest i5100W Manual de usuario

TYAN

TYAN Tempest i5100T Manual de usuario

TYAN

TYAN THUNDER K8QS PRO Manual de usuario

TYAN

TYAN TIGER K8W Manual de usuario

TYAN

TYAN TAHOE-A ATX Manual de usuario

TYAN

TYAN TOMCAT I815E Manual de usuario

TYAN

TYAN S8812 Manual de usuario

TYAN

TYAN S8020 Manual de usuario

TYAN

TYAN THUNDER N6650W Manual de usuario

TYAN

TYAN TOMCAT I II Manual de usuario

TYAN

TYAN THUNDER I7525 Manual de usuario

TYAN

TYAN S8212 Manual de usuario

TYAN

TYAN Thunder n3600M (S2932) Manual de usuario

TYAN

TYAN THUNDER K8HR Manual de usuario

TYAN

TYAN Thunder n3600QX Manual de usuario

TYAN

TYAN Tempest i5400XT S5396 Manual de usuario

TYAN

TYAN TRINITY 450 Manual de usuario

TYAN

TYAN THUNDER K8SE Manual de usuario

TYAN

TYAN Tiger i7500 Manual de usuario

TYAN

TYAN Tiger 100 S1832DL Manual de usuario

TYAN

TYAN S7040 Manual de usuario

Manuales populares de Placa madre de otras marcas

DFI

DFI SD170 Manual de usuario

ASROCK

ASROCK ROMED8-2T Manual de usuario

Asus

Asus P2L97A Manual de usuario

Winmate

Winmate IC70 Manual de usuario

Asus

Asus MES-B Manual de usuario

Grantech

Grantech SYS8F377VGGA-3OMN Manual de usuario

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manual de usuario

Gigabyte

Gigabyte GA-9IVDT Manual de usuario

Texas Instruments

Texas Instruments ADS8372EVM Manual de usuario

Commell

Commell MS-C73 Manual de usuario

IBT Technologies

IBT Technologies MB860 Manual de usuario

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manual de usuario

Biostar

Biostar M7VIT Bravo Instrucciones de funcionamiento e instalación

Intel

Intel D33217CK Manual de usuario

Asus

Asus F1A55-M LX PLUS R2.0 Manual de usuario

EPC

EPC EPC9147C Manual de usuario

Asus

Asus EX-B760M-V5 D4 Manual de usuario

EPOX

EPOX MU-8KHA0010 Manual de usuario