Turbosound IMPACT35 Manual de usuario
Quick Start Guide
IMPACT series
IMPACT Quick Start Guide - Page - 1
Models covered by this Quick Start Guide
IMPACT35, IMPACT55T, IMPACT65T.
Thank you for choosing a TURBOSOUND IMPACT series loudspeaker product for your application. If you would like
further information about this or any other TURBOSOUND product, please contact us. A detailed user manual on this
product is available on our web site at www.turbosound.com
Unpacking the Impact Loudspeakers
After unpacking the loudspeakers please check carefully for damage. If damage is found please notify your supplier at
once. You, the consignee, must instigate any claim. Please retain all packaging in case of future re-shipment.
System Requirements
Low Impedance Systems
When used as part of a low impedance system Impact series loudspeakers require only one amplifier channel for correct
operation, the frequency splitting between the LF driver and the HF driver being accomplished by the internal passive
crossover network built into each enclosure. Select the 16Ωsetting on the voltage tap changer on the bottom of the
cabinet. Amplifiers should be capable of delivering long term broadband power equal to the loudspeaker’s program power
rating at its stated nominal impedance.
Use with Subwoofers
Passive subwoofers such as the TSB-110 can be added to increase low frequency performance without the need for
additional power amplifiers. The subwoofer’s internal crossover filters high frequency signals out of the subwoofer
cabinet to ensure a clean transition. Connect first to the subwoofer and then link out to the satellite speakers.
R
R
LL
POWER AMPLIFIER
IMPACT 3
5
TSB-110
EQ
Distributed Systems
Impact loudspeakers can be used on 70 volt or 100 volt distributed systems. Connect
loudspeakers to a suitable distribution amplifier, making sure that the maximum sum of the
loudspeakers’ transformer taps do not exceed the distribution amplifier’s rated power
output. Adjust the voltage tap selector to provide the appropriate loudness level.
Loudspeaker Connections
Electrical connections to the IMPACT loudspeaker are provided as an integral part of the adjustable wall bracket supplied
with each loudspeaker. Simply follow the instructions in the Mounting and Fixing section following.
7.5
15
15
30
60
30
100V
70V
60
Quick Start Guide
IMPACT series
IMPACT Quick Start Guide - Page - 2
Mounting and Fixing
Installing the Loudspeaker with the Supplied Wall Bracket
•The loudspeaker connections are provided as an integral part of the wall bracket.
•Site the bracket on to the mounting surface, making sure there is sufficient free
travel vertically and horizontally to allow full angle adjustment of the loudspeaker,
and feed the speaker cables through the main bracket assembly from the rear.
•Fix the wall bracket securely to the mounting surface using appropriate fixings. The
correct hole spacing and bracket orientation are shown here.
•Terminate the speaker cable by stripping to length and connecting to the bracket
assembly, ensuring correct polarity. Use the smaller Allen key to tighten the grub
screws on to the cable. The right terminal is positive (+ve) and the left terminal is
negative (-ve).
•Offer the loudspeaker up to the bracket and lock into place with a downward motion.
This action automatically closes the electrical connections.
•Angle the loudspeaker as required and lock the bracket using the larger Allen key
provided.
Installing the Loudspeaker with other Wall and Ceiling Brackets
•When installing IMPACT loudspeakers with CB-10, WB-10 or OmniMount brackets
you will need to terminate the cables directly at the loudspeaker as shown.
•Unscrew the M6 countersunk bolts holding the bracket shoe. Leaving the bracket
shoe in place attach the wall or ceiling bracket directly to the loudspeaker’s M6 fixing
points using the screws provided with the bracket. Angle as necessary and tighten
all fixings.
Spares and Accessories
LS-35 3.5” low frequency driver for IMPACT35
LS-50 5” low frequency driver for IMPACT55T
LS-51 5” low frequency driver for IMPACT65T
TW-52 High frequency tweeter for IMPACT35/55T/65T
WB-5 Adjustable plastic wall bracket
WB-10 Adjustable steel wall bracket
CB-10 Adjustable steel ceiling bracket
Turbosound Ltd, Star Road West Sussex RH13 8RY, United Kingdom
tel: +44(0)1403 711447 fax: +44(0)1403 710155 www.turbosound.com
version 1.0
73mm [2.9"]
97mm
[3.8"]
+ve v
e
+ve
terminal
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Oradores de Turbosound
Turbosound
Turbosound Manchester Series Manual de usuario
Turbosound
Turbosound KT-HP Series Manual de usuario
Turbosound
Turbosound NuQ102-AN Manual de usuario
Turbosound
Turbosound Impact 50 Manual de usuario
Turbosound
Turbosound iNSPIRE iP300 Manual de usuario
Turbosound
Turbosound TXD-081 Manual de usuario
Turbosound
Turbosound TCI-R Series Manual de usuario
Turbosound
Turbosound TCI32-T-WH Manual de usuario
Turbosound
Turbosound TCS-61 Manual de usuario
Turbosound
Turbosound TBV118L Guía de inicio rápido
Turbosound
Turbosound NuQ PRO Series Manual de usuario
Turbosound
Turbosound TCS62 Manual de usuario
Turbosound
Turbosound QLight TQ-425 Manual de usuario
Turbosound
Turbosound MILAN MI5 Manual de usuario
Turbosound
Turbosound TQ Series Manual de usuario
Turbosound
Turbosound Milan M18 Manual de usuario
Turbosound
Turbosound iNSPIRE iP2000 Manual de usuario
Turbosound
Turbosound Manchester Series Manual de usuario
Turbosound
Turbosound QLight TQ-115DP Manual de usuario
Turbosound
Turbosound TSTAND-01 Manual de usuario
