Turbolock TL114 Manual de usuario
In order to continue serving our customers
and providing the best products, our
product information including our user
manuals may receive updates from time
to time. Please check our website for the
latest user manuals and product materials.
Version 4.0 6/05/20
www.turbolock.com
Customer Service: 855-850-8031
Section 1
Information & Safety Warnings 4
1.1 Introduction 4
1.2 Safety Warnings 4
1.3 End-of-Life Disposal 5
Section 2
Package Contents & Overview 6
2.1 Contents 6
2.2 Overview 6
2.3 Battery Information 7
2.4 Usage Overview 7
Section 3
Installation (Retrot) 8
3.1 Pre-Installation 8
3.2 Main Installation 10
Section 4
Installation (New) 12
4.1 Pre-Installation 12
4.2 Main Installation 16
Section 5
Using the Lock 18
Section 6
Keypad Passcodes 18
6.1 Changing the Admin Passcode 18
6.2 Adding Keypad Passcodes 19
6.3 Delete a Single Passcode 19
6.4 Delete All Passcodes 20
6.5 Passcode Disguise 20
Section 7
Using the Mute Function 21
7.1 Activating Mute Mode 21
7.2 Deactivating Mute Mode 21
Section 8
Resetting the Lock 22
Section 9
Specications 23
Section 10
Maintenance 23
Section 11
Troubleshooting 24
Section 12
Warranty 26
12.1 Violation 26
12.2 Information 26
Table of Contents
4 TURBOLOCK TL114
Section 1
Information & Safety Warnings
1.1 Introduction
This user manual will guide you through the functions and usage of your TURBOLOCK TL114. It is important that you follow all
instructions and regard all notes that appear throughout this manual. Consult this manual before you attempt to use your lock. If you
have questions not answered by this manual or are in need of repair or non-routine service, contact customer service at 1-855-850-
8031. Before contacting customer service, please have your purchase information ready as this may be needed during the call.
Please record this information below:
Date of Purchase:
Place of Purchase:
1.2 Safety Warnings
When reading this manual, note these icons:
Notes with this icon MUST be read, understood, and obeyed to prevent injury or damage.
Notes with this icon include relevant information.
General Precautions
• The lock shall only be used as described in this manual.
• Verify that all parts of the lock are accounted for. If any part is missing, contact customer service.
• If the battery compartment or surrounding parts are damaged, do not use the lock.
• Use only 9V alkaline batteries (one is included).
• Never insert objects into the lock other than batteries as described in this manual.
• The lock is not a toy. Do not leave children unsupervised around the lock.
TURBOLOCK TL114 5
• Use only the parts included in the original packaging or received from TURBOLOCK.
• Verify all surfaces are at and level before beginning installation. Installation on doors or surfaces with any type of
deformity such as gaps or warping may cause the lock to malfunction or fail to operate entirely.
• Expected use is for standard doors made for buildings within the US.
• New batteries on average can deliver up to one full year of use before replacement is needed. Battery life varies by
usage.
• Replace the batteries after receiving the lock’s low battery notication.
• Never apply any cleaner directly to any part of the lock. Only use clean (or puried) water and mild cleaner on a soft,
non-abrasive cloth when cleaning.
• Potential Shock Warning: Do not allow water and/or liquids to get into the lock’s electric parts.
• Never submerge the lock or any of the lock’s components.
• Hanging objects on the lock is not recommended.
1.3 End-of-Life Disposal
This product must not be disposed of by incineration, landlling, or mixing with household trash. Improper disposal of the
battery contained within this product may result in the battery heating up, rupturing, or igniting which may cause serious injury.
The substances contained inside the battery present chemical risks to the environment. The recommended disposal for any
TURBOLOCK TL114 at its end-of-life is to dispose of the entire unit at or through an e-waste recycling center, program, or facility.
Local regulations and laws pertaining to the recycling and disposal of certain types of batteries and/or products containing them
will vary according to country, state, and local governments. Please check laws and regulations corresponding to where you live in
order to properly dispose of the battery and/or unit. It is the user’s responsibility to dispose of their waste equipment properly with
accordance with local regulations and laws.
For additional information about where you should drop off your batteries or electronic waste, please contact your local or regional
waste-management ofce, your household waste disposal service, or your point-of-sale.
1: Battery Compartment
2: Inside Knob
3: Mounting Screws
4: Wood Screws
5: Latch Assembly
6: Micro-USB Charging Port
7: Speaker
8: Outside Knob
9: Key Hole
10: Keypad
11: Outside Assembly
12: Power Cable
13: Inside Assembly
14: Reset Button
6 TURBOLOCK TL114
Section 2
Package Contents & Overview
2.1 Contents
TL114 Lock x 1
Outside Knob x 1
Inside Knob x 1
Latch Assembly x 1
Wood Screws x 6
Mounting Screws x 2
Keys x 3
- Mounting screws may already be
inside the lock upon opening.
- Requires 9V alkaline batteries (included).
2.2 Overview
2
1
4
3
5
13
7
8
6
14
9
10
11
12
TURBOLOCK TL114 7
2.3 Battery Information
The lock requires 9V alkaline battery. New battery should be installed as soon as possible after receiving the rst low-battery
warning, as indicated by a single red ash on the indicator and a voice conrmation (“Low battery. Please replace the battery.”).
After that rst notication, the lock will only have enough power for approximately 50 uses before the batteries are fully depleted.
Low-battery notication will come from the lock itself.
2.4 Usage Overview
When using keypad passcodes, the TL114’s backlight will turn on. The door can only be opened while the backlight is on. After a
couple seconds of inactivity, the backlight will turn off and the TL114 will automatically lock. You can also use one of the included
physical keys to open the lock directly.
Using the Admin Passcode
Use the keypad to enter the Admin Passcode, and then press ‘#’ to unlock the door.
For added security, the Admin Passcode must be changed from the manufacturer’s default after installation and initial testing.
See Section 6.
Using the Emergency Power Port
Supply power via the Emergency Power Port on the bottom of the lock. The backlight will turn on indicating the lock is receiving
power. Enter a passcode and then press ‘#’ to unlock the door as usual.
Using a User Passcode
Use the keypad to enter the passcode, then press ‘#’ to unlock the door.
• The TL114 features a Mute Function. See Section 7.
• If a passcode has been entered wrong 5x in a row, the lock will go into a 5-minute period of inactivity where it cannot be used,
except with the included physical key. This is a security feature designed to prevent unwanted parties from using the lock.
8TURBOLOCK TL114
Section 3
Installation (Retrot)
This section details installation steps needed if you are installing the TL114 on a door with a single cutout already
made. Replacing an older xture with a newer one is known as a retrot. If your door has never had a lock or doorknob
installed or otherwise has no cutout, please skip to Section 4.
• For easier installation, have another person help to hold the lock.
• Remove all parts of any old lock before installing the TL114. In some cases, the old strike plate and/or box may be used.
• For your convenience, installation instructions are broken into segments. Read and follow the instructions for both Pre-
Installation and Main Installation.
• If your door happens to have two cut-outs, check the clearance between the two. Make sure there is enough distance so that
you may seal off the extra opening.
3.1 Pre-Installation
Part 1 - Disassemble the Lock
The TL114 comes already assembled. Before
installation, release the wood screws and
mounting screws to disassemble the lock into
three main parts: Outside Assembly x 1, Inside
Assembly x 1, Latch Assembly x 1 (Fig. 1).
Wood Screws
Mounting Screws
Inside Assembly
Outside Assembly
Latch Assembly
(Fig. 1)
TURBOLOCK TL114 9
Part 2 - Installing the Latch
KEEP DOOR OPEN AT ALL TIMES SHORTLY BEFORE, DURING AND SHORTLY AFTER INSTALLATION. If the lock is
incomplete or improperly installed, the lock and/or door may become stuck.
After nishing installation, be sure to use the door at least once to make sure all parts of the lock function correctly.
Step 1. Check the dimensions of the door before installing the latch (Fig. 2).
Step 2. Insert the latch into the hole and check it. The latch’s plate should sit ush against the edge of the door (Fig. 3). If
there’s too much space behind the latch or if it’s sticking out from the door, the latch should be adjusted. If the latch
needs adjusting, continue on to Step 3; otherwise, go to Step 4.
Step 3. Turn the latch and extend or retract it as needed. Make sure the metal peg pops into one of the two square holes in the
side and the deadbolt is pushed all the way in while adjusting the latch’s length (Fig. 4). Insert the latch back into the
door.
Step 4. Add 2x wood screws and use a screwdriver (not included) to secure them (Fig. 5).
23/4” (70mm)
Or 23/8” (60mm)
21/8” (54mm) Hole
1” (25mm)
Door Edge
2
3/4
”2
3/8
”
(Fig. 2) (Fig. 3) (Fig. 4) (Fig. 5)
2
3/4
”2
3/8
”
2
3/4
”2
3/8
”
Part 3 - Installing the Strike
In most cases, the existing strike plate and setup can be used. If you wish to use the one included with your lock, skip to Section
4.1, Part 3.
10 TURBOLOCK TL114
3.2 Main Installation
Step 1. Use a screwdriver to extend the bolt.
The bolt must be EXTENDED prior to installing the lockset (Fig. 7).
Step 2. Install the outside section:
a. Gently feed the power cable through diameter hole carefully over the latch. (Fig. 6)
b. Adjust the latch pin to HORIZONTAL position, then insert it into the center hole of the
latch.(Fig. 6)
Ensure the bolt is EXTENDED and latch pin is HORIZONTAL when installing
outside section.
Do NOT force the cable’s connector end through any part of the lock.
Damaging the connector may make the lock unusable.
Step 3. Hold the outside section then continue the installation on inside section. If needed,
have someone to hold the outside section to help you complete the following steps.
Step 4. Remove battery compartment cover. (Fig. 9) Then carefully connect the two power cables. (Fig. 10) Ensure the
connector is seated properly and rmly.
Step 5. Adjust the thumb of inside section to VERTICAL position. (Fig. 8)
Step 6. Assemble the inside section on door by aligning mounting holes on the latch and inside section.Ensure the latch pin is
HORIZONTAL when inserting it into inside section. Then secure the inside section on the door with mounting screws.
(Fig. 11)
Horizontal
Latch Pin
Fig. 6
Power Cable
Rotate 90 degrees
Extended Retracted
Fig. 7
Otros manuales para TL114
1
Tabla de contenidos
Otros manuales de Cerradura de puerta de Turbolock
