Turboair WORKSHOP TA3050 Manual de instalación
COMPRESSOR
WORKSHOP SERIES
SET UP AND OPERATING INSTRUCTIONS
TA3050 CAST IRON DIRECT DRIVE COMPRESSOR
Read this material before using this product.
Failure to do so can result in injury.
SAVE THIS MANUAL
DIRECT DRIVE COMPRESSOR
2.
CONTENTS
Introduction.................................................3
General Safety Rules...................................4
Specic Safety Rules...................................5
Parts Overview.............................................6
Assembling the Compressor........................7
Checking/Filling the Oil................................7
Pre-start Checklist........................................8
Operating Instructions.................................8
Preventative Maintenance Schedule.........10
Troubleshooting.........................................11
Glossary of Terms.......................................16
Warranty...................................................17
Notes...................................................18
DIRECT DRIVE COMPRESSOR
3.
Congratulations on the purchase of your
TURBO AIR Direct Drive Compressor!
This product is manufactured to high quality standards
and will give you many years of service if you follow the
instructions for use and maintenance in this manual. If you
require any help with your product, whether it is a warranty
claim, spare part or user information, please visit www.
euroquip.co.nz rst and register your product online.
Once registered, please log a request online or call us on
0800 387 678. Your new Turbo Air compressor has been
manufactured under stringent AS/NZS Quality Standards to
meet superior performance criteria.
COMPRESSOR USAGE
This compressor has been designed for home workshop use and
ideal for the many tasks around home and in the shed that are
so much easier and quicker using the power and convenience of
compressed air.
ENVIRONMENT PROTECTION
Recycle unwanted materials instead of disposing of them as
waste. All tools, hoses and packaging should be sorted, taken to
the local recycling centre and disposed of in an environmentally
safe way.
DESCRIPTION OF SYMBOLS
The rating plate on your tool may show symbols. These represent
important information about the product or instruction on it’s use.
Wear hearing protection
Wear eye protection
Wear breathing protection
Conforms to relevant standards for
electromagnetic compatibility.
INTRODUCTION
SPECIFICATIONS:
• Powerful3.0HPInductionMotor
Designed for Aus / NZ conditions
• CastIronV-TwinPump
Super duty
• Large50LTankCapacity
Provides volume for high air demand applications
• 8Bar(115psi)
High pressure air delivery
• TwinOutletswithPressureRegulator
Includes 2 x quick release couplers
• HighCapacity300L/minFAD
(Free air delivery)
MODEL: TA3050
POWER: 3.0HP / 2250W
VOLTAGE: 230V~50Hz
NO LOAD SPEED: 2850rpm
CURRENT: 10A
MAX. OUTPUT: 360L/min, 12.7cfm
TANK CAPACITY: 50L
AIR OUTLET: 6.35mm (1/4”)
ARO Coupler x 2
CUT IN PRESSURE: 0.6Mpa (Factory Set)
MAX. OUTPUT PRESSURE: 0.8MPA (115psi)
FREE AIR DELIVERY: 300L/min
DIMENSIONS: 760 x 380 x 740mm (LxWxH)
WEIGHT: 37kg
CAUTION!
Carefully read through this entire instruction manual before
using your new compressor. Take special care to heed the
cautions and warnings. Your Iron Horse Compressor has
many features that will make your job faster and easier.
Safety, performance and dependability have been given top
priority in the development of this machine, making it easy
to maintain and operate.
DIRECT DRIVE COMPRESSOR
4.
GENERAL SAFETY RULES
WARNING!
Read and understand all instructions. Failure to follow all
instructions listed below may result in electric shock, re,
and/or seriouis personal injury.
DIRECT DRIVE COMPRESSOR
5.
SPECIFIC SAFETY RULES
DIRECT DRIVE COMPRESSOR
6.
PARTS OVERVIEW
1. Compressor Pump
2. On / Off Pressure Switch
3. Safety Valve
4. Pressure Regulator
5. Regulator Gauge
6. Tank Gauge
12
8
4
7
9
11
10
3
5
6
7. Air Tank
8. Non Return Valve
9. Drain Valve
10. Electric Motor
11. Air Filters
DIRECT DRIVE COMPRESSOR
7.
ASSEMBLINGTHECOMPRESSOR
This air compressor requires some minor assemble before it can
be used. Locate the accessory pack. It should contain:
• WheelsandAxleSet
• RubberStopper
• AirFilter
• OilBreatherPlug
• ABottleofOil
1. Fit the wheels to
the unit using the axle
kit provided and insert
the rubber stopper into the
spigot on the bottom of the tank.
2. Fit the air lter to the
cylinder head.
3. Locate the plastic dust plug
in the oil breather hole and
remove it to expose the oil
breather hole.
1. Always check the oil
level in the pump before
use. When lling, ll the oil
from the oil breather hole
until the oil reaches the red
mark on the sight glass.
RecommendedCompressorOil:
Use SAE30 for temperatures over 10oand use SAE10 below 10o.
NOTE: The oil must be changed after the rst 10 hrs of operation
then every 20 hrs thereafter.
CHECKING/FILLINGTHEOIL
WARNING!
This unit is shipped with oil in the compressor pump. Oil
must be added to the unit prior to operating.
2. Check that the small hole
in the top of the breather
pipe is clear and then
insert it into the oil ller
hole.
DIRECT DRIVE COMPRESSOR
8.
PRE-STARTCHECKLIST
• Ensure the unit is stable in a well-ventilated dry position.
• Ensure that the drain valve is closed and all air outlets are
closed.
• Connect the power lead to the mains.
• Start the compressor by pulling on the red knob.
• Check for air leaks.
NOTE: Output ttings may differ from those shown
OPERATING INSTRUCTIONS
The pressure in the tank is controlled by the action of the pressure
switch located under the pressure switch cover.
When the set maximum pressure is reached the pressure switch
activates and the motor is turned off. The pressure will then de-
crease as the air is used until the set minimum is reached after
which the pressure switch turns the motor on again.
The operator of the compressor should be well aware that during
use of the compressor the motor will cycle (start and stop) under
the inuence of the rising or falling pressure in the tank and the
motor will start without any warning.The maximum and minimum
pressures are factory set and should not be altered.
You can utilize either the direct outlet and/or the regulated outlet.
The pressure of the regulated outlet can be changed by turning the
control knob. Rotate the knob clockwise to increase pressure and
anti-clockwise to decrease.
EACHTIMEYOUUSETHECOMPRESSOR
Please read the owners manual thoroughly. Make sure that you
completely understand all of the safety warnings, system controls
and instructions provided before attempting to operate this air
compressor. Every effort has been made to provide you with the
information needed to obtain many years of reliable and trouble-
free service out of your new air compressor. It is your responsibility
to operate the air compressor properly. To obtain the longest pos-
sible service life from your compressor you must always keep the
following instructions in mind:
WARNING!
Use the red knob to turn the unit on and off, not the mains
switch. Turning the unit on and off from the mains only will
result in damage to the motor. Regulator Gauge
Safety Valve
Tank Gauge
Air Outlet
Pressure Regulator
Turn Off
Turn On
DIRECT DRIVE COMPRESSOR
9.
ALWAYSMAKESUREYOU:
DIRECT DRIVE COMPRESSOR
10.
PREVENTATIVEMAINTENANCESCHEDULE
WARNING!
Before maintenance operation, stop the air compressor, disconnect the unit from the mains supply and discharge
all air in the air tank.
IMPORTANT! The pump oil must be changed after the rst 10 hours of operation. This
will remove contaminants contained in the crankcase due to break-in Recommended
Compressor Oil: Use SAE30 for temperatures over 10oC and use SAE10 below 10oC.
Tabla de contenidos
Otros manuales de Compresor de aire de Turboair
