TTS Tuff-Cam 2 Manual de usuario
User Guide
Version 1
Please Read All Instructions Carefully Before Using
Tuff-Cam 2 User Guide
2
•Please retain these instructions for future reference
•Tuff-Cam 2 contains a non-replaceable,
rechargeable battery
•Do not attempt to remove the battery
•In the event of an electro-static discharge, your
Tuff-Cam 2 may malfunction In this case, please
use a pen to operate the reset switch on the side to
restore normal operation
•Warranty is void if the case is opened for any reason
•The warranty does not cover any data loss from the
unit nor any consequential loss of information
FCC compliance
NOTE:
THE MANUFACTURER IS NOT RESPONSIBLE FOR
ANY RADIO OR TV INTERFERENCE CAUSED BY
UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT SUCH MODIFICATIONS COULD VOID
THE USER AUTHORITY TO OPERATE THE
EQUIPMENT
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules These limits are designed to provide
reasonable protection against harmful interference in a
Tuff-Cam 2 User Guide
3
residential installation This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications However, there is no
guarantee that interference will not occur in a particular
installation
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna
•Increase the separation between the equipment and
receiver
•Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected
•Consult the dealer or an experienced radio/TV technician
for help
Tuff-Cam 2 User Guide
4
Know Your Tuff-Cam 2
22
2
Tuff-Cam 2 User Guide
5
Taking a Photo
•Slide the Mode switch to PHOTO
•Turn ON the camera, by pressing the On/Off
switch briefly
•Point the camera at the subject
•Press the trigger button to take the photo
•Pressing the OK button will cycle through the flash
modes: Auto, Forced ON, Forced OFF
•Press the << or >> to zoom in or out of the photo
Taking a ideo
•Slide the Mode switch to VIDEO
•Turn ON the camera, by pressing the On/Off
switch briefly
•Point the camera at the subject
•Press the trigger button briefly to start the video
•Press << or >> to zoom in or out
•Press the trigger button again to finish the video
Tuff-Cam 2 User Guide
6
•NB You can also press and hold the trigger button
and Tuff-Cam 2 will take a video for the whole time
that the button is pressed (memory permitting)
Displaying the Photos & ideos
•Slide the Mode switch to PLAY
•Turn ON the camera, by pressing the On/Off
switch briefly
•The most recent Photo or Video taken will be
displayed on the screen
•Use the >> and << buttons to move between
images
•Press the OK button to play and pause videos
Switching ON and OFF
•To switch ON, press the On/Off button briefly
•To switch OFF, press and hold the On/Off button
for 3 seconds
Tuff-Cam 2 User Guide
7
Using the Menu System
•There are different Menu options available for the
different positions of the Mode switch; Play, Video
and Photo
•Press the Menu button briefly to enter the
appropriate Menu options for the selected Mode
•Press the Menu button once more to move the to
Setup options, which are available in all Modes
•Use the << and >> buttons to move around the
Menus
•Use the OK button to select a Menu item
•Some menus have multiple pages If you use the <<
or >> buttons to move off the top or bottom of a
page, the previous or next page is shown
•Press the Menu button once more to exit the Menu
system
PHOTO Menu Options
•Size/Resolution: VGA up to 12 Mpixel
•Quality: Economy, Standard, Fine
•Scene mode: Auto, Sport, Night, Portrait,
Landscape, Backlight
Tuff-Cam 2 User Guide
8
•EV/Exposure correction: -2 0 to +2 0
•White balance: Auto, Daylight, Cloudy, Tungsten,
Fluorescent
•ISO: Auto, 100, 200
•Colour: Standard, Vivid, Sepia, Monochrome
•Saturation: Normal, High, Low
•Sharpness: Normal, Hard, Soft
•Preview: On, Off
•Time stamp: Off, Date only, Date & Time
•Burst: On, Off
SETUP Menu Options
•Format: Yes, No
•Beep: On, Off
•Language: English, French, German, etc
•Auto off: 1 min, 3 min, 5 min, Never
•System Reset: Yes, No
•Light frequency: 50Hz, 60Hz
•TV Out: NTSC, PAL
Tuff-Cam 2 User Guide
9
•Date Input: Date setting menu
IDEO Menu Options
•Size/Resolution: VGA, QVGA
•EV/Exposure correction: -2 0 to +2 0
•White balance: Auto, Daylight, Cloudy, Tungsten,
Fluorescent
PLAY Menu Options
•Delete: Single, All, Selection
•Copy to Card: Single, All, Selection
•Slide show: 3 sec, 5 sec, 10 sec
•Protect: Single, All, Selection
•Thumbnail:
•Volume: 1 to 8
Connecting to a PC or Apple Mac
•There are two modes in which the Tuff-Cam 2 can
connect to a PC: MSDC or PC-CAM
Tuff-Cam 2 User Guide
10
•In MSDC mode, the PC or Mac will recognise the
device as a USB mass storage device and it will appear
as a removable drive in the file explorer window
•In PC-Cam mode, only MS Windows based
computers are supported and the drivers (see below)
must be installed first
•To select MSDC mode, move the slide switch to
PLAY before connecting to the PC
•To select PC-Cam mode, move the slide switch to
PHOTO or VIDEO before connecting to the PC
Charging the Battery
•Tuff-Cam 2 is supplied with a partially charged battery
and can be used immediately without charging first
•The battery can be charged by connecting to any
active USB port This will take between 2 and 4 hours
depending on the state of the battery
•While the battery is charging, the Battery Status LED
will flash
•When Tuff-Cam 2 is fully charged, the Battery Status
LED will change to solid Red
Otros manuales para Tuff-Cam 2
2
Tabla de contenidos
