TrueNAS ES102 Manual

TrueNAS®ES102 Basic Setup Guide
Version 1.05

Contents
1 Introduction ������������������������������������������������������������������������������������������������������������������������ 1
1�1 Safety �������������������������������������������������������������������������������������������������������������������������� 1
1�1�1 Static Discharge ���������������������������������������������������������������������������������������������������������������������� 1
1�1�2 Handling the System ���������������������������������������������������������������������������������������������������������������� 1
1�2 Requirements ���������������������������������������������������������������������������������������������������������������� 1
2 ES102 Components ���������������������������������������������������������������������������������������������������������������� 2
2�1 Front Indicators �������������������������������������������������������������������������������������������������������������� 3
2�2 Rear Components and Ports ����������������������������������������������������������������������������������������������� 3
3 Install Railkit ����������������������������������������������������������������������������������������������������������������������� 4
3�1 Install Chassis Rails ���������������������������������������������������������������������������������������������������������� 4
3�2 Install Rack Rails ������������������������������������������������������������������������������������������������������������� 5
4 Install Cover Retention (Optional) �������������������������������������������������������������������������������������������� 6
4�1 Attach Cage Nuts ������������������������������������������������������������������������������������������������������������ 6
4�2 Attach Retention Brackets �������������������������������������������������������������������������������������������������� 6
5 Install Latch Plates ��������������������������������������������������������������������������������������������������������������� 7
6 Mount the ES102 in the Rack ��������������������������������������������������������������������������������������������������� 8
6�1 Attach Cover Retention Screws �������������������������������������������������������������������������������������������� 9
6�2 Shipping Screws �������������������������������������������������������������������������������������������������������������� 9
7 Install Cable Management Arms ��������������������������������������������������������������������������������������������� 10
7�1 Attach the Cable Management Brace ����������������������������������������������������������������������������������� 10
7�2 Attach the Lower Cable Management Arm ����������������������������������������������������������������������������� 10
7�3 Attach the Upper Cable Management Arm ����������������������������������������������������������������������������� 11
8 Install Drives ���������������������������������������������������������������������������������������������������������������������� 12
8�1 Attach Clip to Drive ��������������������������������������������������������������������������������������������������������� 12
8�2 Insert Drives into the Enclosure ������������������������������������������������������������������������������������������ 12
8�3 Drive LED Indicators �������������������������������������������������������������������������������������������������������� 12
9 Connect Power Cables ���������������������������������������������������������������������������������������������������������� 13
10 Connect SAS Cables ������������������������������������������������������������������������������������������������������������ 14
10�1 R50 ��������������������������������������������������������������������������������������������������������������������������� 14
10�2 M60 �������������������������������������������������������������������������������������������������������������������������� 15
10�3 Route SAS Cables ���������������������������������������������������������������������������������������������������������� 16
11 Additional Resources ���������������������������������������������������������������������������������������������������������� 17
12 Contacting iXsystems ��������������������������������������������������������������������������������������������������������� 17
Copyright © #### iXsystems, Inc. All rights reserved. All trademarks are the property of their respective owners.

Page 1
1 Introduction
The TrueNAS ES102 is a 4U, 102-bay, storage array� It has redundant I/O modules and power supplies�
The ES102 is much larger than other Expansion Shelves sold by iXsystems� Take full safety precautions when
installing or servicing the enclosure�
1.2 Requirements
1.1 Safety
1.1.1 Static Discharge
Static electricity can build up in your body and discharge when touching conductive materials� Electrostatic
Discharge (ESD) is harmful to sensitive electronic devices and components� Keep these safety recommendations in
mind before opening the system case or handling non-hot-swappable system components:
• Turn o the system and remove power cables before opening the case or touching internal components.
• Place the system on a clean, hard work surface like a wooden tabletop� Using an ESD dissipative mat can also
help protect the internal components�
• Touch the metal chassis with your bare hand to dissipate static electricity in your body before touching any
internal components, including components not yet installed in the system� Using an anti-static wristband and
grounding cable is another option�
• Store all system components in anti-static bags�
You can nd more preventative tips and details about ESD at https://www�wikihow�com/Ground-Yourself-to-Avoid-
Destroying-a-Computer-with-Electrostatic-Discharge�
We recommend at least two people lift a TrueNAS system�
Hold the system from the sides or bottom whenever possible� Always be mindful of loose cabling or connectors and
avoid pinching or bumping these elements whenever possible�
This document uses “left” and “right” according to your perspective when facing the front of a system or rack�
1.1.2 Handling the System
You will need these tools to properly install the ES102 in a compatible rack:
• Long T15 screwdriver
• #2 Philips head screwdriver�
You don’t need these items, but they can be useful when installing the ES102:
• Tape measure
• Level
• Flat head screwdriver
• Cable ties�
The ES102 weighs 70 lbs unloaded and requires a minimum of two people to lift�
Do not attempt to lift the ES102 when it is fully populated with drives! The fully-populated system is over 260
lbs� When removing a fully-populated system from a rack, remove the drives before de-racking the enclosure�
You need at least 37�5” (952�5mm) empty space in front of a racked ES102 to fully extend the enclosure to access
all drive bays� The high weight of the enclosure can be a tipping hazard for the rack� Be sure to follow all tipping
prevention instructions recommended by your rack provider before installing the ES102�

Page 2
2 ES102 Components
TrueNAS units are carefully packed and shipped with trusted carriers to arrive in perfect condition�
If there is any shipping damage or missing parts, please take photos and contact iXsystems support immediately at
support@ixsystems�com, 1-855-GREP4-iX (1-855-473-7449), or 1-408-943-4100�
Please locate and record the hardware serial numbers on the back of each chassis for quick reference�
Carefully unpack the shipping boxes and locate these components:
102 drive clips with HDDs, shipped separately�
One Cable Management Arm (CMA), a CMA
brace, and bag with cable ties�
ES102 Expansion Shelf
Left and right cover retention brackets�
Set of rackmount rails�
Accessory kit with two IEC C14 to C13 power
cords, velcro strips, Two 3-meter Mini SAS HD to
Mini SAS HD cables, and racking hardware�

Page 3
2.1 Front Indicators
2.2 Rear Components and Ports
Indicators on the front panel show identication and status. The fault indicator is on during the initial power-on self-
test (POST) or when the TrueNAS software has issued an alert� These indicators are also on the back panel�
Light Color and Indication
Blinking Blue: Locate ID is active�
Blinking Amber: Fault / Alert�
Green: ES102 is on�
Power Supply 1
Power Supply 2
Fan 1 Fan 2 Fan 3 Fan 4
HD
SAS3
HD
SAS3
HD
SAS3
HD
SAS3
HD
SAS3
HD
SAS3
SAS Indicators

Page 4
3 Install Railkit
ES102 requires 4U of space in an EIA-310 compliant rack that is 47�24” (1200mm) deep, from frame to frame� The
vertical rack rails need to be between 31�5” - 36�2” (800mm - 920mm) apart to properly install the ES102 rails�
We recommend adjusting the front vertical rack rails to be as close to the front as possible to prevent the cable
management arms (CMAs) from protruding from the back of the rack�
The system with CMAs attached is 47�1 (1197mm) deep�
The rack must be a standard 17�72” - 18�31” (450mm - 465mm) wide, although a minimum 29�5” (750mm) cabinet
width allows for using a ZeroU PDU with the ES102� Narrower cabinets could require a rack-mounted PDU for the
system to fully install in the rack with the included CMA�
For 52U racks, we recommend the AR3357X674� For a 42U rack, we recommend the AR3350 APC�
We recommend using the bottom-most 4U space in the rack to balance the system weight with other equipment�
For both the AR3357X674 and AR3350 APC rack, we recommend using the STV-4501, STV-4502, or STV-4503 PDU�
3.1 Install Chassis Rails
Each rack rail includes an inner chassis rail you must remove� Extend the innermost chassis rail as shown below
until you fully expose the metal safety catch� Push the safety catch in and continue to pull out the chassis rail until it
is completely free from the rack rail� Repeat the process for the second rail�
The chassis rails attach to each side of the ES102� Align the chassis rail keyholes over the ES102 side posts� Slide the
rail towards the rear of the system until the rail locks into place� Use three of the low-prole M4 screws to secure
the rail� Repeat for on the other side� The Cable Management Arm bracket must be at the back of the system�
PRESS PULL
M4 Screw M4 Screw M4 Screw

Page 5
The ES102 occupies 4U of rack space� The front rail pins mount to the 4U bottom-most attach points, and the back
rail pins mount one space above the 4U bottom-most attach points� The rails have left side “L” and right side “R”
stamps�
Install the front of the rail rst. Align the rail pins with the mounting holes in the rack and push forward until the
front latch clicks into place on the rack� Make sure an additional 2U of rack space is available above the rail�
The rear of the rail can adjust to racks with 32” -36” of space between the front and rear rack posts�
Align the rear rail pins with the rack mounting holes and push forward until the blue release catch clicks into place
over the rack� Note that the rear rail pins install one mounting hole higher than the front rail pins� You can use a
level to ensure the front and back of the rail are even�
3.2 Install Rack Rails
When installed correctly, the front and rear of the rail is level and the inner part of the rail with the gray bearing
sleeve faces the inside of the rack� Use the same procedure to install the other rail� Be sure to install both left and
right rails at the same height in each rack post�
Use three of the included washers and T15 M5 screws to secure the rear of the rail to the rack post�
Front Rear
T15 M5
Screws
Rear

Page 6
4 Install Cover Retention (Optional)
4.1 Attach Cage Nuts
4.2 Attach Retention Brackets
The cover retention components hold the cover in place when the unit slides forward out of the rack, simplifying
drive bay access� If you want cover retention, install alignment brackets over the rear of the rack rails� Then install
cage nuts at the system’s front for the cover retention screws�
You need two square cage nuts�
Place a cage nut in the reserved 4U topmost rack mounting hole. A at head screwdriver can help push the cage nut
“wings” into the rack mounting hole�
The nut should be inside the rack, with the “wings” touching the left and right sides of the hole (horizontal).
Repeat this process for the other rack post and make sure to install both cage nuts in parallel rack mounting holes�
Place the Cover Retention Bracket over the rail and align it with the mounting holes on the rear of the rack rail� The
groove in the bracket must point toward the inside of the rack. Use ve washers and T15 M5 screws to secure the
bracket to the rear of the rack rail�
Use the same method to install the second alignment bracket to the other rail� Make sure the grooves on top of
both brackets point inside the rack� The ES102 cover slides into the grooves when it is pushed into the rack�
4U
Front
T15 M5
Screws
Rear

Page 7
5 Install Latch Plates
The latch plates attach to the front of the rack rails� They secure the rails to the rack and hold the enclosure in place
when fully inserted in the rack� Align a plate over the three holes between the rack rail front mounting pins� The
ange must point to the outside of the rack. Use three T15 M5 screws to secure the latch plate, rack post, and rack
rails together�
Use the same precess to install the second plate. Ensure the anges both latch plates face the outside of the rack.
Front
T15 M5 Screws

Page 8
6 Mount the ES102 in the Rack
Slide the middle part of the rack rails out of the rack until they click into place� Make sure the inner bearing sleeve is
also slid as far forward as possible�
Lift the ES102 and align the chassis rails with the middle rack rails� Push the ES102 into the rack rails until it stops�
Locate the metal safety catches on each chassis rail and squeeze them into the chassis� Hold the safety catches in
place and push the chassis into the rack until the chassis latches touch the rail latch plates�
Ensure the enclosure cover slides into the Alignment Bracket grooves at the rear of the rack�
To minimize jarring motions, gently secure the ES102 in place by swinging the front handles out and pushing the
enclosure forward until it is fully in the rack� When you release the handles, the enclosure latches catch behind the
latch plates and hold the system in the rack�
Caution: When using a lift, you need two people and 7ft of clearance between the system front and the rack�
When lifting unaided, you need three people and 5ft of clearance to safely lift and install the chassis� Do not
install drives until the chassis is installed in the rack� Remove all drives before removing the chassis from the rack�
Warning: Do not use the front handles to lift the ES102! The handles are only for unlatching and sliding the
enclosure after attaching it to the rack rails� They cannot support the system’s weight�
Otros manuales para ES102
2
Tabla de contenidos
Otros manuales de Hardware de red de TrueNAS
Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor
Yudor YDS-16 Manual de usuario

D-Link
D-Link ShareCenter DNS-320L Manual de usuario

Samsung
Samsung ES1642dc Instrucciones de uso

Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje













