True TRCB-52 Manual de usuario

............ www.truemfg.com ............

TABLE OF CONTENTS

Safety Information

Safety Precautions 1

Proper Disposal 2

Connecting Electricity 3

Adapter Plugs 3

Installation / Operation Instructions

Ownership 4

Required Tools 4

Uncrating 4

Locating & Installation of Leg/Castors 5

Leveling Cabinet & Electrical Inst. 6

Wire Gauge Chart 7

Start-up 8

Maintenance, Care & Cleaning

Cleaning Condenser Coil 9-10

Temperature Control Adjustment 11

Stainless Steel Equipment Care & Cleaning 12-13

Warranty (U.S.A. & Canada Only!) 14

INSTALLATION MANUAL FOR CHEF BASE EQUIPMENT

(TRCB MODELS) CHEF BASE

EQUIPMENT

TRUE FOOD SERVICE EQUIPMENT, INC.

2001 East Terra Lane • P.O. Box 970 • O’Fallon, Missouri 63366

(636)-240-2400 • FAX (636)272-2408 • INT’L FAX (636)272-7546 • (800)325-6152

Parts Department (800)424-TRUE • Parts Department FAX# (636)272-9471

CONGRATULATIONS!

You have just purchased the finest commercial

refrigerator available. You can expect many years of

trouble-free operation.

TRCB-82

TRCB-52

1/9/07-3k SB #897012

*Spanish, German, and French versions included.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

............ www.truemfg.com ............

SAFETY INFORMATION

True Food Service Equipment, Inc.

This refrigerator must be properly installed and

located in accordance with the Installation

Instructions before it is used.

Do not allow children to climb, stand or hang

on the shelves in the refrigerator. They could

damage the refrigerator and seriously injure

themselves.

Do not touch the cold surfaces in the refrigera-

tor compartment when hands are damp or wet.

Skin may stick to these extremely cold surfaces.

Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

Keep fingers out of the “pinch point” areas;

clearances between the doors and between the

doors and cabinet are necessarily small; be

careful closing doors when children are in the

area.

NOTE: We strongly recommend that any

servicing be performed by a qualified

individual.

Unplug the refrigerator before cleaning and

making repairs.

Setting temperature controls to the 0 position

does not remove power to the evaporator fans.

WARNING!

Use this appliance for its intended purpose as described in

this Owner Manual.

How to Maintain Your

Unit to Receive the Most Efficient and

Successful Operation

You have selected one of the finest commercial refrigeration units made. It is

manufactured under strict quality controls with only the best quality materials

available. Your TRUE cooler when properly maintained will give you many

years of trouble-free service.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

............ www.truemfg.com ............

True Food Service Equipment, Inc.

SAFETY INFORMATION

PROPER DISPOSAL OF THE REFRIGERATOR

DANGER!

RISK OF CHILD ENTRAPMENT

USE OF EXTENSION CORDS

NEVER USE AN EXTENSION CORD! TRUE will not warranty any refrigerator that has been

connected to an extension cord.

Child entrapment and suffocation are not problems

of the past. Junked or abandoned refrigerators are

still dangerous… even if they will sit for “just a few

days.” If you are getting rid of your old refrigerator,

please follow the instructions below to help

prevent accidents.

Before You Throw Away Your Old Refrigerator

or Freezer:

Take off the doors.

Leave the shelves in place so that children may

not easily climb inside.

Refrigerant Disposal

Your old refrigerator may have a cooling system

that uses “Ozone Depleting ” chemicals. If you are

throwing away your old refrigerator, make sure the

refrigerant is removed for proper disposal by a

qualified service technician. If you intentionally

release any refrigerants you can be subject to

fines and imprisonment under provisions of the

environmental regulations.

The power cord of this appliance is equipped with

a 3-prong (grounding) plug which mates with a

standard 3-prong (grounding) wall outlet to mini-

mize the possibility of electric shock hazard from

this appliance.

Have the wall outlet and circuit checked by a quali-

fied electrician to make sure the outlet is properly

grounded.

If the outlet is a standard 2-prong outlet, it is your

personal responsibility and obligation to have it

replaced with the properly grounded 3-prong wall

outlet.

The refrigerator should always be plugged into it’s

own individual electrical circuit, which has a volt-

age rating that matches the rating plate.

This provides the best performance and also pre-

vents overloading building wiring circuits which

could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the

power cord. Always grip plug firmly and pull

straight out from the outlet.

Repair or replace immediately all power cords that

have become frayed or otherwise damaged. Do not

use a cord that shows cracks or abrasion damage

along its length or at either end.

When removing the refrigerator away from the

wall, be careful not to roll over or damage the

power cord.

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

For personal safety, this appliance must be properly grounded.

WARNING!

USE OF ADAPTER PLUGS

NEVER USE AN ADAPTER PLUG! Because of potential safety hazards under certain conditions, we

strongly recommend against the use of an adapter plug.

............ www.truemfg.com ............

SAFETY INFORMATION

True Food Service Equipment, Inc.

(North America Use Only!)

NEMA plugs

TRUE uses these types of plugs.

If you do not have the right outlet

have a certified electrician install

the correct power source.

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

To insure that your unit works properly from the

first day, it must be installed properly. We highly

recommend a trained refrigeration mechanic and

electrician install your True equipment. The cost

of a professional installation is money well spent.

Before you start to install your True unit, carefully

inspect it for freight damage. If damage is discov-

ered, immediately file a claim with the delivery

freight carrier.

True is not responsible for damage incurred

during shipment.

OWNERSHIP

Adjustable Wrench

Phillips Head Screwdriver

Level

REQUIRED TOOLS

Step 1

The following procedure is recommended for

uncrating the unit:

A. Remove the outer packaging, (cardboard and

bubbles or styrofoam corners and clear plastic).

Inspect for concealed damage.Again, immedi-

ately file a claim with the freight carrier if there

is damage.

B. Move your unit as close to the final location as

possible before removing the wooden skid.

UNCRATING

INSTALLATION / OPERATION INSTRUCTIONS

REMOTE UNITS (This section applies to

remotes only!)

• Remote cabinets must be ordered as remote.

We do not recommend converting from a

standard self contained to remote system.

• All remote cabinets must be hard wired.

• No castors available.

• All remote cabinets come standard using 404A

refrigerant.

• All remote units come standard with expansion

valve, liquid line solenoid, heated condensate

pan, and defrost timer when applicable.

• Contact True Technical Service for BTU

requirements.

• No wiring necessary between cabinet and

condensing unit.

• All remote condensing units purchased from

True are 208/230 volts single phase.

If you have any questions regarding this

section, please call True at 1-(800)-325-6152.

............ www.truemfg.com ............

INSTALLATION / OPERATION INSTRUCTIONS

True Food Service Equipment, Inc.

Step 2

A. Place packing material behind cabinet as a

cushion. Carefully lay the unit on its back to

remove skid.

When lifting unit remember to

leave the cabinet upright for 24 hours before

plugging into power source.

B. Remove skid by unscrewing all base rail anchor

brackets. Place skid to the side.

C. Carefully lift cabinet upright.

LOCATING

Leveling Shims

Castor

Snug Fit

Here

Leveling Shims

Side View

Top View Left Shim

In Position

Castor

Mounting

Plate

Removing

skid from

bottom of

cabinet.

INSTALLATION OF LEGS AND CASTORS

Important Safeguard for installation of leg/castor (Images 1 & 2 demonstrate procedure)

Step 3

Leveling Castors

Four sets of shims have been provided in warranty

packet for leveling castored units positioned on

uneven floors. Shims must be positioned between

cabinet and castor mounting plate.

(See image 1 below).

If the cabinet is not level prop up one end of the

cabinet between castors with a 6” block.

(See image 2)

NOTE:

Do not push block more than 5” under cabinet.

Loosen castor bolts with an adjustable wrench

enough to slide shims between the castor mount-

ing plate and cabinet bottom.

Install the desired number of shims (in pairs as

shown in image 1), making sure the slots in the

shim are in contact with the castor mounting bolts.

Tighten and secure the shims and castor(s).

Remove 6” block and check to determine if cabinet

is level. Repeat process until cabinet is level.

Ensure that the drain hose or hoses are positioned

in the pan.

F°

35°

6”

(Image 1.)

(Image 2.)

............ www.truemfg.com ............

True Food Service Equipment, Inc.

Step 5

A. Before your new unit is connected to a power

supply, check the incoming voltage with a volt-

meter. If anything less than 100% of the rated volt-

age for operation is noted, correct immediately.

B. All units are equipped with a 6 ft. (1.83 m) serv-

ice cord, and must be powered at proper operating

voltage at all times. Refer to cabinet data plate for

this voltage.

True requires that a sole use circuit be dedicated

for the unit. Failure to do so voids warranty.

WARNING

Compressor warranties are void if compressor

burns out due to low voltage.

WARNING

Power supply cord ground should not be

removed!

NOTE

To reference wiring diagram - Remove front

louvered grill, wiring diagram is positioned on the

inside cabinet wall.

ELECTRICAL INSTRUCTIONS

Step 4

A. Set unit in its final location. Be sure there is ade-

quate ventilation in your room. Under extreme

heat conditions, (100°F+, 38°C+), you may want to

install an exhaust fan.

Warning

Warranty is void if ventilation is insufficient.

B. Proper leveling of your True cooler is critical to

operating success (for non-mobile models).

Effective condensate removal and door operation

will be effected by leveling.

C. The cooler should be leveled front to back and

side to side with a level.

D. Ensure that the drain hose or hoses are posi-

tioned in the pan.

E. Free plug and cord from inside the lower rear

of the cooler (do not plug in).

F. The unit should be placed close enough to the

electrical supply so that extension cords are never

used.

Warning

Compressor warranties are void if compressor

burns out due to low voltage. Power supply cord

ground should not be removed!

LEVELING

INSTALLATION / OPERATION INSTRUCTIONS

............ www.truemfg.com ............

INSTALLATION / OPERATION INSTRUCTIONS

True Food Service Equipment, Inc.

Wire Gauge for 2% Voltage Drop in Supply Circuits

115 Volt Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

2 141414141414141414141414

3 141414141414141414141412

4 141414141414141414121212

5 141414141414141212121010

6 141414141414121212101010

7 1414141414121212101010 8

8 14141414121212101010 8 8

9 141414121212101010 8 8 8

10 14 14 14 12 12 10 10 10 10 8 8 8

12 14 14 12 12 10 10 10 8 8 8 8 6

14 14 14 12 10 10 10 8 8 8 6 6 6

16 14 12 12 10 10 8 8 8 8 6 6 6

18 14 12 10 10 8 8 8 8 8 8 8 5

20 14 12 10 10 8 8 8 6 6 6 5 5

25 12 10 10 8 8 6 6 6 6 5 4 4

30 12 10 8 8 6 6 6 6 5 4 4 3

35 10 10 8 6 6 6 5 5 4 4 3 2

40 1088665544322

45 1086665443321

50 1086654433211

Wire Gauge for 2% Voltage Drop in Supply Circuits

230 Volts Distance In Feet To Center of Load

Amps 20 30 40 50 60 70 80 90 100 120 140 160

5 141414141414141414141414

6 141414141414141414141412

7 141414141414141414141212

8 141414141414141414121212

9 141414141414141412121210

10 14 14 14 14 14 14 14 12 12 12 10 10

12 14 14 14 14 14 14 12 12 12 10 10 10

14 14 14 14 14 14 12 12 12 10 10 10 8

16 14 14 14 14 12 12 12 10 10 10 8 8

18 14 14 14 12 12 12 10 10 10 8 8 8

20 14 14 14 12 10 10 10 10 10 8 8 8

25 14 14 12 12 10 10 10 10 8 8 6 6

30 14 12 12 10 10 10 8 8 8 6 6 6

35 14 12 10 10 10 8 8 8 8 6 6 5

40 14 12 10 10 8 8 8 6 6 6 5 5

50 12 10 10 8 6 6 6 6 6 5 4 4

60 12 10 8 6 6 6 6 6 5 4 4 3

70 10 10 8 6 6 6 5 5 4 4 2 2

80 1088665544322

90 1086655443311

100 1086654433211

CONDUCTORS AND CIRCUITS

............ www.truemfg.com ............

True Food Service Equipment, Inc.

INSTALLATION / OPERATION INSTRUCTIONS

Step 6

A. The compressor is ready to operate. Plug in the

cooler.

B. Temperature control set at No. 4 position gives

refrigerators an approximate temperature of 35°F.

Allow unit to function several hours, completely

cooling cabinet before changing the control set-

ting.

C. Excessive tampering with the control could

lead to service difficulties. Should it ever become

necessary to replace temperature control, be sure it

is ordered from your True dealer or recommended

service agent.

D. Good air flow in your True unit is critical. Be

careful to load product so that it neither presses

against the back wall, nor comes within four inches

of the evaporator housing. Refrigerated air off the

coil must circulate down the back wall.

NOTE

If the cooler is disconnected or shut off, wait five

minutes before starting again.

RECOMMENDATION

Before loading product we recommend you run

your True unit empty for two to three days. This

allows you to be sure electrical wiring and instal-

lation are correct and no shipping damage has

occurred. Remember, our factory warranty does

not cover product loss!

REPLACEMENT PARTS

TRUE maintains a record of the cabinet serial

number for your cooler. If at any time during the

life of your cooler, a part is needed, you may

obtain this part by furnishing the model number

and serial number to the company from whom

you purchased the cooler. Call Toll-Free: (800)-

424-TRUE (Direct to Parts Department). (800)-

325-6152 (U.S.A. & Canada only) or call: (636)-

240-2400.

STARTUP

Otros manuales para TRCB-52

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Refrigerador de True

True

True TAC-48GS Manual de usuario

True

True TBB-2G Manual de usuario

True

True GDM-33C Manual de usuario

True

True TRCB-79-86 Manual de usuario

True

True TG1DT-2HS Manual de usuario

True

True TM-74-6 Manual de usuario

True

True GDM-5 Manual de usuario

True

True GDM-10-58 Manual de usuario

True

True TG2R-4HS Manual de usuario

True

True T-23DT Manual de usuario

True

True TA2RRT-2G-2S Manual de usuario

True

True TRCB-52-60 Manual de usuario

True

True RESIDENTIAL ADA HEIGHT TURADA-24-R/L-RS-A-S Instrucciones de montaje

True

True TUC-36 Manual de usuario

True

True TS-72G Manual de usuario

True

True GEM-72FC Manual de usuario

True

True T-23PT Manual de usuario

True

True TUR-24-R/L-SS-A Manual de usuario

True

True T-24-GC Manual de usuario

True

True TR1DT-2HS Manual de usuario

True

True TS-53-4 Manual de usuario

True

True T-49 Manual de usuario

True

True TWT-60-32D-2 Manual de usuario

True

True TG1RRT-1S-1S Manual de usuario

Manuales populares de Refrigerador de otras marcas

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Manual de usuario

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Manual de usuario

Sharp

Sharp SJ-BA31IEXW2-EU Manual de usuario

CORBERO

CORBERO CC2300MCW Manual de usuario

KitchenAid

KitchenAid 2205264 Manual de usuario

Stengel

Stengel KU 1101 A++ Manual de usuario

NEFF

NEFF KI181 Series Manual de usuario

Hoshizaki

Hoshizaki Reach-In Manual de usuario

Amana

Amana ASD2524VES00 Manual de usuario

BOMANN

BOMANN KGC 213 Manual de usuario

Danby

Danby DAR044A1SLDD Instrucciones de montaje

Samsung

Samsung RF323TE Manual de usuario

Beko

Beko CSA31022 Manual de usuario

IKEA

IKEA FROSTIG C 185 E Manual de usuario

Electrolux

Electrolux ER 6821 D Manual de usuario

Frigidaire

Frigidaire FSC23R5DW9 Manual de usuario

Beko

Beko LSP4579W Manual de usuario

Teledyne

Teledyne 6712FR and Instrucciones de funcionamiento