TruckForce 3500 Instrucciones de funcionamiento

Operating and

Maintenance Manual

Models:

TruckForce 3500

TruckForce 1200

Congratulations and thank you for buying a TRUCK-

FORCE

portable extractor. The TruckForce is designed to

give you truckmount performance in a portable machine that

is versatile to use and easy to transport. Years of experience,

engineering, planning, and practical know-how has gone into

the design and manufacture of the TruckForce. We take a

great deal of pride in TruckForce and want you to be com-

pletely satisfied with your purchase. Please take the time to

read this manual before operating the machine—it will be

time well spent.

SETUP AND OPERATION

ELECTRICAL CONNECTIONS

Plug electrical cords into grounded wall outlets. Truck-

Force is designed to run on a 15 AMP and a 20 AMP circuit

(the left hand cord). You will normally find 20 AMP separate

circuits in the kitchen and in bathrooms. Never remove the

ground plug from the end of the cord. f a circuit breaker trips

during operation, reset the breaker and move electrical cord

to different outlet and resume operation. When cords are

plugged into “live” receptacles, the control switches will

glow. f the lights on the switches do not glow, this indicates

that the wall receptacle may be dead. Simply move the cord to

a different outlet.

WARNING:

The Tru kFor e is designed for use

with water based leaning solutions, su h as, low

foaming detergents or a id rinses. NEVER USE DRY

SOLVENT SOLUTIONS! The use of dry solvents in

your Tru kFor e will void the warranty.

AUTOMATIC CHEMICAL FEED

Chemical Metering: The TruckForce may be equipped with

an automatic water fill/chemical feed metering system. As the

solution tank fills with water, cleaning concentrate is drawn

into the solution tank at a designated rate via a metering tip. A

complete set of metering tips is included.

To adjust the amount

of cleaning concentrate

being drawn, simply

remove the plastic sup-

ply tube from the

chemical feed metering

valve (see Figure 1).

Unscrew the colored

metering tip and

replace with the tip

that corresponds to the

portable dilution ratio

for your cleaning product (refer to Figure 2). Reconnect the

plastic supply tube.

Liquid Concentrates: TruckForce comes with the purple

metering tip installed at the factory. This tip is rated for .25

oz. of chemical per gallon of water, which is a standard dilu-

tion ratio for the most popular liquid cleaning products on the

market. Refer to your product’s dilution ratio for portable

extractors, and select the proper metering tip from Figure 2

(“Liquid Concentrated Dilution Ratio”).

Powder Concentrates: For powdered cleaning detergents,

a liquid concentrate must be made. Combine two (2) cups of

powder in a one gallon solution jug. Fill the jug with water up

to the one gallon mark. Use the tip that corresponds to the

portable dilution ratio for your powdered cleaning product

(refer to Figure 2, “Powder Concentrated Dilution Ratio”).

Fresh Water Rinse: For fresh water rinsing simply leave

the chemical supply tube in the solution tank.

Manual Filling: To use the TruckForce without the auto-

matic filling system, simply pre-mix your solution in a bucket

of water, and pour into the solution tank. See Figure 3 for a

detailed break-down of the chemical feed system.

Figure 2

Setup: nside the solution tank is a bottle float suspended

on a chain. The length of the chain determines the level of

solution in the tank and can be adjusted. Check the chemical

feed supply foot valve for debris, and clean if necessary.

nsert the line into the cleaning concentrate so that it touches

the bottom of the bottle. Set cleaning concentrate in the solu-

tion holder/pouring funnel provided.

TRUCKFORCE®

MasterBlend (800) 525-9644

Figure 1

Metering Tip Replacement

Concentrated Dilution

Ratio (oz/gal)

Tip Color Liquids Powders

Clear 0.25 —

Purple 0.50 —

Yellow 1.00 —

Green 1.50 —

Pink 2.00 0.25

Turquoise 3.20 0.40

Black 4.00 0.50

Gray 5.00 0.63

Red 6.50 0.81

Blue 8.00 1.00

Brown 10.50 —

White 13.00 —

Orange 16.00 —

None 35.00 —

Metering Tip Dilution Ratios

TRUCKFORCE®

Connect the fill hose to the quick disconnect located on the

side of the machine. Attach the water supply hose to any

available faucet. A faucet-to-hose adapter is provided to prop-

erly attach your water supply hose to the most commonly

found faucets. t may require adapters to fit the various faucet

combinations you will encounter. Never force a threaded fit-

ting. Place a towel over the faucet connection so that any

spray will be controlled. Turn on the water and check the

hose connections for leaks.

The solution tank will fill approximately 14 gallons, which

can be increased by shortening the chain. As the tank is filling,

cleaning concentrate is being drawn into the solution tank.

Shutdown: Before the end of each job, turn off the water

supply, to prevent the solution tank from being completely full.

With the cleaning completed and the solution pump turned off,

disconnect the fill hose from the faucet, drain the water in the

fill hose back into the solution tank, and remove the fill hose.

Remove the chemical feed supply tube from the chemical solu-

tion jug and clean the filter. Vacuum out the solution tank.

MODEL SPECIFICATIONS

The TruckForce utilizes either a PumpTec™ twin piston

500 PS or 1200 PS pump. Both pumps are adjustable from

either 50–500 PS for the TruckForce 3500 or 100–1200 PS

for the TruckForce 1200. Do not exceed the pressure limita-

tions of 500 PS for the TruckForce 3500 or 1200 PS for the

TruckForce 1200. The TruckForce 3500 pump is adjustable

with a pressure relief valve shown on page 14. The pressure

regulator is located by the pressure gauge on the front of the

machine and is easily adjusted by turning the regulator clock-

wise to increase the pressure and counterclockwise to

decrease the pressure. The TruckForce 1200 pump is

adjustable with an unloader valve which is also located by the

pressure gauge on the front of the machine. The pressure

gauge on the TruckForce 1200 will register pressure when

your wand or other tool is hooked up to your high pressure

solution line and the valve is depressed, allowing solution to

go through the wand or tool. The pressure on the TruckForce

1200 is adjusted by turning the unloader valve clockwise to

increase pressure and counter-clockwise to lower the pres-

sure. Do not exceed 1200 PS on the TruckForce 1200.

Priming the Solution Pump: f you are experiencing

pressure fluctuations, pulsation in the solution hose, or not

maintaining pressure, you will need to prime the solution

pump by engaging the Power Prime Valve located next to the

pressure regulator on the front of the machine. Making sure

there is sufficient water in the solution tank, depress the

Power Prime Valve and any air will be immediately purged

out of the pump system and pressure should immediately be

restored. Cauti n: Please be aware that depressing the P wer

Prime Valve will als spray b th air and water ut the b t-

t m f the valve. If y u wish t av id having water n the

fl r, y u sh uld have y ur vacuum h se h ked up t the

machine, have the vacuum m t rs n and have the vacuum

cuff n the end f the vacuum h se held under the P wer

Prime Valve t catch any water c ming ut f the valve.

VACUUM SYSTEM

Vacuum Motors: The TruckForce utilizes a unique two-

or three-vacuum system which produces both outstanding

vacuum lift and air flow for superior extraction and drying

times. The vacuum system can be used with one or two vac-

uum motors for cleaning delicate fabrics, or all three vacuum

motors for carpet cleaning and water extraction.

Waste Tank: The vacuum system requires proper mainte-

nance of the waste tank filter bag. Refer to the

MA NTENANCE section for removal and proper cleaning of

the filter.

t is also necessary to use a defoamer to eliminate foam

build-up in the waste tank which could lead to foam/moisture

entering the vacuums and contributing to early failure of the

vacuum motors. Failure to properly maintain the filtration

system and utilize defoamer, will void the warranty on the

vacuum motors.

f moisture does enter the vacuum motors, refer to “WD-40

Vac Motors” under MA NTENANCE. To prevent moisture

from damaging the vacuum motors during storage, empty the

waste tank and store with the lid open.

AUTOMATIC WASTE PUMP-OUT

Connect the black 1-1/4˝ x 50´ drain hose to the automatic

pump-out port located in the upper left corner on the front of

the machine. Secure the other end of hose where you wish to

direct the discharge of waste water, such as a toilet or sink.

Fasten the discharge end of hose tightly. Turn on the Auto-

matic Pump-Out switch. The pump will turn on

automatically when water in the waste tank is approximately

2/3 full. The pump will discharge the waste water down to a

level of about 2 inches in the waste tank. DO NOT TURN

ON THE AUTOMAT C PUMP-OUT SW TCH W THOUT

THE DRA N HOSE N PLACE. This pump-out system has

been designed to stay up with flood restoration work and is

capable of pumping 20 gallons per minute.

Electrical 115 Volt, 60 hz (230 Volt, 50 hz)

Vacuum Dual 2-stage; Three 2-stage

Solution Pump 500 PS

1200 PS

Solution Tank 22 Gallons (83 liter)

Waste Tank 15 Gallons (56 liter)

Height 451/2inches (116cm)

Length 32 inches (81cm)

Width 241/2inches (62cm)

Power Cords 50 feet (15m)

MasterBlend (800) 525-9644

TRUCKFORCE®

ITEM# PART# PART DESCRIPTION

1 740100 COMPLETE ASSEMBLY

2 740102 BODY/DIAPH AGM ASSEMBLY

3 740103 BODY

4 740104 DIAPH AGM

5 740105 CLOSING SP ING

6 740106 VALVE COVE O- ING

7 740107 VALVE COVE

8 740108 VALVE COVE SC EWS (PAI )

9 740109 SHUT OFF VALVE ASSEMBLY

10 A SHUT OFF DISC & STEM ASSM

11 B SHUT OFF SP ING

12 C SHUT OFF PLATE

13 D SHUT OFF STEM O- ING

ITEM# PART# PART DESCRIPTION

14 E SHUT OFF COVE O- ING

15 F SHUT OFF COVE

16 G STEM NUT WITH SET SC EW

17 H LEVE ASSEMBLY

18 I LEVE ASSEMBLY SC EWS (2)

19 740119 UBBE WASHE

20 740120 BACKFLOW P EVENTE

21 740121 P OPO TIONE

22 740122 METE ING TIP KIT

23 740123 CHEMICAL SUPPLY TUBING

24 740124 FOOT VALVE

25 740125 DISCHA GE TUBING

26 740126 FLOAT ASSEMBLY

Figure 3

AUTOMATIC CHEMICAL FEED SYSTEM

MasterBlend (800) 525-9644

TRUCKFORCE®

ACCESSING COMPONENTS

Drain the solution and waste tanks, disconnect all hoses,

and unplug the electrical cord(s).

To access the pump/motor, fresh water filter, and plumb-

ing components, lay the TruckForce on its back and remove

the 6 Phillips-head screws holding the bottom plate to the

body. Slowly lower the bottom plate to the ground.

To access the vacuum motors, cooling fan(s), switches, and

other electrial components: remove the 6 Phillips-head screws

on the back plate and the 3 Phillips-head screws securing the

switch plate. Slowly lower the back plate. When the back plate

is partially open, loosen and remove the vacuum hose from

vacuum #1 by loosening the clamp with a 5/16 driver or

screwdriver. This vacuum hose is not long enough to allow

the back plate to be completely lowered to the ground.

To retrun to operation, reverse the above steps. Make sure

the vacuum hose is properly re-installed on vacuum #1 and

that the hose clamp is secure.

FILL HOSE SCREEN

Located in the female garden hose fitting on the Automatic

Fill Hose. Remove screen, clean, and replace.

CHEMICAL FEED FOOT VALVE

The foot valve is on the end of the chemical supply tube of

the automatic chemical feed system. t is not necessary to

remove the filter from the tubing. Just rinse with fresh water.

f necessary, use a tooth brush to remove detergent build-up.

Note: a heavy build-up is a warning sign that the solution sys-

tem should be flushed—see “Flushing Solution System.”

FRESH WATER TANK FILTER

Located inside the bottom plate by the pump at the bottom

of the solution tank. Unscrew the filter counterclockwise and

rinse with fresh water. f necessary use a tooth brush to

remove detergent build-up. Note: a heavy build-up is a warn-

ing sign that the solution system should be flushed—see

“Flushing Solution System.”

WASTE TANK FILTER BAG

The waste tank filter bag should be cleaned out after every

job. This filter bag will catch the larger debris and most lint.

The filter bag is attached by a drawstring. Loosen the draw-

string, clean the filter bag, and reinstall. Never operate the

TruckForce without the filter bag in place.

PERATI N INTERVAL

Clean Fill Hose S reen Ea h Job/Daily

Clean Chemi al Feed Foot Valve Ea h Job/Daily

Clean Fresh Water Filter Weekly

Clean Waste Tank Filter Bag Ea h Job/Daily

Clean Va Shut Off S reen Daily

Clean Auto Pump-out Daily As Needed

Clean Wand Jets Weekly

Run Auto Pump-out Every Two Weeks

Flush Solution System Monthly

WD-40 Va Motors As Needed

The above operations are fully outlined on the following two pages. Proper maintenance is necessary to

achieve maximum operating performance from your TruckForce. Failure to properly maintain your

machine could void the warranty.

Maintenance

MasterBlend (800) 525-9644

VAC SHUT OFF

The TruckForce utilizes a ball float shutoff system, which

shuts off the flow to the vacuum motors when solution

reaches the appropriate level to activiate the ball shutoff. This

shutoff has been designed to protect the vacuum motors from

excess water entering the vacuum motors provided that the

owner is utilizing a defoamer chemical to prevent foam

and moisture from entering the vacuum stack and,

therefore, the vacuum motors.

Twist off the ball assembly from the stand pipe, and clean

the screen. t may be rinsed with water. This screen should

be cleaned frequently if the TruckForce is being operated in

an environment which has an abnormal buildup of lint and

debris, such as cleaning newly installed carpet. Loss of vac-

uum is most normally associated with lint and hair buildup in

the waste filter bag and the float ball shutoff assemble at the

top of the vacuum stand pipe.

AUTO PUMP-OUT

The Automatic Pump-Out system is capable of handling

most debris that passes through the waste filter bag. How-

ever, for optimum performance, keep the waste tank clean

and remove debris from the filter screen of the pump-out.

This should be done on a daily basis, or as needed, depending

upon use, and amount of debris.

Every two weeks, run the pump-out with a full tank of

clean water, to insure that debris and lint are not accumulat-

ing in the base of the pump.

To service the pump-out more thoroughly, unhook the vac-

uum cuff, cut the zip tie around the looped electrical cord,

and lift it out of the waste tank. Unsnap the screen from the

bottom, clean the screen, and clean out the area inside.

f necessary, remove the six screws holding the base to the

motor housing, and clean the base. f the impeller is removed

make sure that a spacing of .050” with shaft pushed toward

housing is maintained when reassembled.

WAND JETS

Remove jets and visually check for wear and debris. Water

or compressed air is best for cleaning—NEVER use a metal

object to remove debris, as it may damage the jet orifice. f

excessive wear is apparent, the jet should be replaced. f the

wand is equipped with jet screens, those should be cleaned by

rinsing with water. Hook up the wand to machine, and check

jet alignment.

FLUSH SOLUTION SYSTEM

At least once a month, the TruckForce, hoses, and tools

should be flushed to remove alkaline residues. Follow the

steps on page 8 of the “Recommended Procedure for Stor-

age,” using a solution of one part warm water with three

parts white vinegar, in place of the antifreeze solution. Then,

repeat the steps using two gallons of fresh water.

WD-40 VAC MOTORS

Should moisture ever enter the vacuum motors, completely

drain the waste tank, open the waste tank lid, remove the vac

shut off ball assembly, turn on all vacuum motors, and spray

a five second burst of WD-40 into the standpipe. Continue to

run the vacuum motors for at least three minutes.

To prevent moisture from damaging the vacuum motors dur-

ing storage, empty the waste tank and store with the lid open.

TRUCKFORCE®

MasterBlend (800) 525-9644

STORAGE AND FREEZE PROTECTION

Care must be taken to protect your TRUCKFORCE® from freezing. Freezing could seriously damage the TruckForce as

well as fittings and valves. Freezing is not covered under the limited warranty and you should always store your equipment

in areas where the temperature remains above 40° F. f you plan on storing the TruckForce for a prolonged period of time,

the following procedure should help prevent your TruckForce from freezing, and prevent the pump seals from drying out.

Recommended Procedure for Storage:

STEP ONE:

n a separate container, mix 1 gallon of water with 1 gallon of automotive radiator antifreeze

(ethylene glycol type). Mix well, and pour into the solution tank, keeping approximately 1

pint for use in Step Five.

STEP TWO:

Connect the pressure hose to the female quick disconnect (QD) on the front of the machine.

Turn the shut off valve on the pressure hose to the off position. nsert an open-ended male

QD into the female QD on the end of the pressure hose.

STEP THREE:

Prime the solution pump, directing the flow of solution back into the solution tank. When

primed, turn down the pressure to 100psi.

STEP FOUR:

Disconnect the open-ended QD and connect the solution hose to the male QD at the auto

fill/chemical feed connection.

CAUT ON: Applying high pressure (over 100 psi) to the chemical feed system will damage

the mechanism.

STEP FIVE:

Place the chemical feed supply tube into the container with the pint of anitfreeze from Step

One, turn on the pump, and allow to circulate for 10 minutes. Check to make sure the chemi-

cal supply tube is drawing the antifreeze solution. This will introduce antifreeze into the

chemical feed system.

STEP SI :

Disconnect the solution hose from the chemical feed, and allow the system to bypass for 10

minutes. This will work antifreeze into the pressure gauge.

STEP SEVEN:

Attach any wands and hand tools that will also be stored with your TruckForce. Open valve

for 30 seconds, directing the spray to the solution tank. Disconnect hose and with valve open

and the jets pointing down, depress the dimple on the male QD. This will drain the solution

out of the tool. Drain thoroughly before storing.

STEP EIGHT:

Vacuum out the solution tank and thoroughly drain the waste tank and vacuum hose. Turn

off the pump and disconnect all hoses and tools.

The automatic pump-out does not require freeze protection, as long as the waste tank is

completely drained, and allowed to thoroughly dry.

Return to Service:

To return the TruckForce to service, flush the pressure system by repeating the above steps,

using fresh water in place of the antifreeze solution.

TRUCKFORCE®

MasterBlend (800) 525-9644

1740215 1 SOLUT ON TANK

2 740100 1 CHEM CAL FEED COMPLETE SEE F GURE 3

3 700236 1 HEX N PPLE 1/2˝X1/4˝

4700313 1 ELBOW STREET 1/4˝ 45*

5 780617 4 SCREW-MACH PH L– 4X1/2˝ SS

6 740235 1 S GN PLATE

7 780214 1 WASHER– 9/16˝X1 1/8˝ SS

8 700111 1 MALE QD 1/4˝

9 740181 1 PVC ELBOW BARB 2˝X2˝MPT

10 740041 1 VAC HOSE/TANK TO VAC 24.5˝

11 705110 2 DRA N VALVE 45* EXT-2˝

12 705102 1 DRA N VALVE 2˝ X 1 1/2˝ MPT

13 740033 1 PVC BARB 2˝ X 2˝ MPT

14 740027 1 CAM LOCK MALE 1-1/4˝ MPT

15 740256 2 RUBBER WASHER 5/16˝X1-3/8˝

16 780213 2 WASHER-3/8˝X1-1/2˝

17 780017 2 BOLT-1/4-20SAE X 1˝ SS

18 & 28 740232 1 PUMPOUT ASSEMBLY W/SW TCH(115V)

18 & 28 740260 1 PUMPOUT ASSEMBLY W/SW TCH(230V)

19 705008 2 VAC CUFF 1-1/4˝ X 1-1/4˝

20 705107 1 DRA N VALVE NUT 1-1/4˝

21 740028 1 CHECK VALVE 1-1/4˝

22 740029 2 PVC BARB 1-1/4˝ X 1-1/4˝ MPT

23 740092 1 VAC HOSE/ AUTO PUMPOUT-9˝

24 740257 1 8˝ DECK L D W/ GASKET

- 740173 GASKET ONLY

- 740174 8˝ DECK L D ONLY

25 740218 1 FLOAT SHUTOFF ELBOW

26 740200 1 FLOAT BALL SHUTOFF

27 702905 3 HOSE CLAMP 2 1/4˝

28 & 18 740232 1 PUMPOUT ASSEMBLY W/SW TCH(115V)

28 & 18 740260 1 PUMPOUT ASSEMBLY W/SW TCH(230V)

29 705105 1 DRA N VALVE NUT 2˝

30 740253 1 PVC 2˝ ELBOW WASTE BAG RET.

31 740036 1 WASTE F LTER BAG

32 740214 1 WASTE TANK

33 740258 1 VAC HOSE/VAC TO MUFFLER 7.5˝ 1200

34 780401 32/35 NUT-NYLOC 1/4˝X20SAE

35 780201 68/80 WASHER-1/4˝

36 740231 1 VACUUM MAN FOLD 2-2 STAGE 1200

37 740226 6/9 VAC SPACER

38 740209 2/3 VAC GASKET

39 740043 2/3 2˝ VAC MOTOR NTAKE FLANGE

40 780016 6/9 BOLT-1/4˝-20SAE X 3 1/2˝

41 724001 1 VAC MOTOR 2-STAGE/093/120V

42 740219 1/2 AX AL FAN 115V

42 740236 1/2 AX AL FAN 230V

43 740203 1 BACK PLATE W/CORD WRAPS

44 780001 18 BOLT-1/4˝-20SAE X 3/4˝

45 780613 12 SCREW-PH L TRUSS 1/4˝-20X 5/8˝

46 724000 1/2 VAC MOTOR 2-STAGE/096/115V

41 & 46 724003 2/3 VAC MOTOR 2-STAGE/196/230V ALL MODELS

TRUCKFORCE®PARTS LIST

TRUCKFORCE®

MasterBlend (800) 525-9644

ITEM # PART # QTY DESCRIPTI N N TES

1200/3500

47 780615 4/8 SCREW-PH L/PAN 6-32X1/2˝

48 780413 4/8 NUT-NYLOC 6-32 18.8

49 740208 1 VACUUM MAN FOLD 3-2 STAGE 3500

* 740233 1 CHEM CAL HOLDER/FUNNEL

50 740206 1 SW TCH PLATE (specify model)

51 740193 1 HOUR METER

52 740211 1 SW TCH DPST RED L GHTED

53 740210 3/4 SW TCH DPST GREEN L GHTED

54 780614 3 SCREW-PH L-TRUSS-10-24X3/8˝

55 780411 2 NUT-NYLOC-5/8˝X11SAE

56 780218 4 WASHER-5/8˝X1-1/8˝

57 740212 2 WHEEL 12˝ FOAM

58 740213 2 CASTER 4˝ X 1.25˝

59 700270 2 COUPLER 1/4˝ X 1/4˝ FPT

60 719000 1 PRESSURE GAUGE “U” CLAMP

61 719003 1 PRESSURE GAUGE-1200 PS 1200

61 719002 1 PRESSURE GAUGE-1000 PS 3500

62 780617 4 SCREW-PH L/PAN 10-32X1/2˝

63 780221 4 WASHER-#10SS

64 780410 4 NUT-10-32

65 700101 1 QD 1/4˝ FEMALE

66 780214 1 WASHER-9/16˝X1-1/16˝SS

67 715011 1 UNLOADER – 1200 PS 1200

67 715022 1 REGULATOR-600PS 3500

- 715023 PRESSURE REG. K T/P STON/UCUP/

68 715025 1 PRESSURE REG. BACK PLATE

69 700307 8 ELBOW STREET 3/8˝

70 715024 1 PRESSURE REG. FRONT PLATE

71 721122 1 PULSEHOSE- 3/8˝ MPT X 3/8˝ FPT

72 721023 1 PULSEHOSE- 3/8˝ FPT X 1/4˝ MPT

73 721221 1 PULSEHOSE- 3/8˝ MPT X 1/4˝ FPT

74 740259 2 HOSE 1/2˝ CLEAR 9˝ SOLUT ON/PUMP

75 702902 2 HOSE CLAMP 1/2˝

76,77,78,79 740221 1 FRESH WATER F LTER 1/2˝ BARBS

80 721401 1 1200 PS PUMP 1200

80 720010 500 PS PUMP 3500

81 721402 MOTOR/115VDC/FOR 1200 PS PUMP 1200

81 726001 MOTOR/115V/.5HP/FOR 500 PS PUMP 3500

82 740142 4 MOTOR MOUNT

83 740055 1 HOSE BYPASS TO SOLUT ON TANK

84 700293 1 HEX PLUG 1/4˝

85 740202 1 BOTTOM PLATE/AXEL/H NGE

86 700303 1 ELBOW STREET 1/4˝

87 700350 1 FLARE 1/2˝ X 1/2˝ MPT 90° ELBOW

88 700329 2 TEE MALE BRANCH - 3/8˝

89 700284 1 BUSH NG 3/8˝ x 1/4˝

90 721113 1 POWER PR ME VALVE

91 740195 1 PR ME VALVE HOSE

*NOT SHOWN ON SCHEMATIC

ITEM # PART # QTY DESCRIPTI N N TES

1200/3500

TRUCKFORCE®

MasterBlend (800) 525-9644

TRUCKFORCE®

MasterBlend (800) 525-9644

Este manual sirve para los siguientes modelos

Tabla de contenidos

Manuales populares de Depurador de otras marcas

Olympus

Olympus M200H Manual de usuario

Clarke

Clarke BEXT 100H Manual de instalación y funcionamiento

JOHNY VAC

JOHNY VAC JVC70BCT Manual de usuario

RCm

RCm Elan Series Manual

Kärcher

Kärcher B 120 W Manual de usuario

Truvox

Truvox Orbis MotorScrubber 20 Manual de usuario

Numatic

Numatic TTB 4045/100 Manual de usuario

U.S. Products

U.S. Products PEX 500-C-TICK Instrucciones de funcionamiento

Mclennan

Mclennan C510 Manual de usuario

Tennant

Tennant T20 LPG Manual de usuario

Columbus

Columbus ARA 66 BM 100 Manual de usuario

Numatic

Numatic TTV 678G / 300T Manual de usuario

American-Lincoln

American-Lincoln 505-945 Manual de usuario

FIORENTINI

FIORENTINI ET 65-75 Manual de usuario

Floorpul

Floorpul ruby 48 blt Guía del usuario

Onyx

Onyx RX-34 Manual de usuario

Dustbane

Dustbane Hurricane 400 Manual de usuario

Sana

Sana EUJ-702 Manual de usuario