Tru-Test S1 Manual de usuario
S1 Weigh System Quickstart Guide
1
QUICKSTART GUIDE
This quickstart guide provides basic instructions for setting up and using the
S1 Weigh System. For further information, visit www.tru-test.com
Contents
Unpacking the box................................................. 1
Installing the S1 Weigh System............................... 2
Weighing an animal............................................... 6
Changing indicator settings.................................... 7
Maintenance and care............................................ 8
Warranty and servicing........................................... 8
1
Unpacking the box
S1 Weigh System Quickstart Guide
2
2
Installing the S1 Weigh System
Before you start:
Fully charge the indicator overnight.
Step 1:
Place the load bars on a flat surface up
to 2.5 m (8') apart.
S1 Weigh System Quickstart Guide
3
Step 2:
Use the supplied bolts to bolt the weigh
platform onto the load bars.
Step 3:
If desired, bolt the load bar feet
onto the ground. In non-permanent
solutions, you can use it without
bolting down, but pay attention to
movement.
S1 Weigh System Quickstart Guide
4
Step 4:
Tuck the load bar cables under the
weigh platform.
Step 5:
Mount the indicator bracket onto an
appropriate support that the indicator
connector on the load bar cable will
reach. Slide the indicator onto the
bracket.
S1 Weigh System Quickstart Guide
5
Step 6:
Plug the indicator connector (on the
load bar cable) into the indicator and
tighten up.
Step 7:
Press to power on the
indicator.
S1 Weigh System Quickstart Guide
6
3
Weighing an animal
Before you begin:
Ensure that the indicator is displaying 0.0 If not, press .
1. Move the animal onto the platform.
2. When the stable light illuminates, the indicator has locked onto the
animal’s weight.
3. Move the animal off the platform.
Note:
If the indicator is not displaying 0.0 between animals or there are
problems with inaccurate or unstable weights, make sure that the bars are
firmly secured to the concrete floor and free from stones or dirt and that the
load bars are properly connected to the indicator.
S1 Weigh System Quickstart Guide
7
4
Changing indicator settings
Data Link enables you to change settings on the indicator, such as displaying
metric or imperial measurements.
1. Ensure that your PC has internet connectivity and download the Data Link
PC Software from livestock.tru-test.com/applications/datalink
2. Plug one end of the USB cable into the indicator and the other end into
your PC.
3. Launch Data Link on your PC; click , and Settings.
S1 Weigh System Quickstart Guide
8
5
Maintenance and care
Keep the underside of the weigh platform and load bars free from dirt or
stones.
Do not leave the indicator, load bars or indicator connector immersed in
water.
Cables should be placed under the weigh platform to prevent damage.
When not in use, always replace the dust cap on the indicator connector.
Remove dust and moisture from the plugs and dust cap using methylated
spirits, ethyl alcohol, or a suitable electrical contact cleaner. Stronger
spirits must not be used, as they may react with the plastic.
6
Warranty and servicing
For service and warranty information, see www.tru-test.com
All trademarks with an * are not owned by Tru-Test Limited and belong to
their respective owners.
Guia Rápido para o Sistema de pesagem S1
9
Este guia rápido fornece as instruções básicas para a instalação e o uso do
sistema de pesagem S1. Para mais informações, visite a www.tru-test.com.
Conteúdo
Desembalar a caixa................................................ 9
Instalar o sistema de pesagem S1......................... 10
Pesar um animal .................................................. 14
Modificar as configurações do indicador............... 15
Manutenção e cuidados....................................... 16
Garantia e assistência .......................................... 16
1Desembalar a caixa
GUIA DE INÍCIO RÁPIDO DO
Guia Rápido para o Sistema de pesagem S1
10
2Instalar o sistema de pesagem
S1
Antes de começar:
Carregue o indicador
completamente durante a noite.
Passo 1:
Coloque as barras de carga verticalmente
em uma superfície plana numa distância
máxima de 2,5 m.
Otros manuales para S1
2
Tabla de contenidos
Idiomas:
Otros manuales de Accesorios de Tru-Test
Tru-Test
Tru-Test EziWeigh5i Manual de usuario
Tru-Test
Tru-Test ID5000 Manual de usuario
Tru-Test
Tru-Test 5000 Series Manual de usuario
Tru-Test
Tru-Test EziWeigh5i Manual de usuario
Tru-Test
Tru-Test HD Series Manual de usuario
Tru-Test
Tru-Test Series 2000 Manual de usuario
Tru-Test
Tru-Test S1 Manual de usuario
Tru-Test
Tru-Test MP600 Manual de usuario
Tru-Test
Tru-Test 2000 Series Manual de usuario
Tru-Test
Tru-Test S2 Manual de usuario
