TRU Audio CP-5 Manual de usuario
Instruction Guide and Owner’s Manual
Choosing the Speaker Location
Before you install your speakers you should take careful consideration of their location. Make
sure to note the location of lighting fixtures, electrical, plumbing and any other obstructions. If
the house was pre-wired at construction time, make sure you know where the speaker cable is
located in the wall or ceiling.
Ceiling Placement: When placing your speakers into the ceiling, if possible, they should
be mounted above the listening area. Take in consideration furniture locations when finalizing
your speaker locations. If the speakers are mounted away from the listening area, adjust the
tweeter so it is pointing toward it.
Prep before Speaker Installation
If you’re your speakers were pre-wired at construction time, your dealer might have used
TRUAUDIO’s Rough-in kits (ES & EL series) prior to drywall at each speaker location. (There
should also be speaker cable at this location). After the drywall is installed and the hole is cut the
speaker is then easily installed. Move on to Speaker Installation.
If the drywall has not been cut please read the following instructions:
Please note, speaker cable should be run to each speaker location prior to speaker installation.
In-Ceiling Architectural Speakers
CP-5 • CP-6 • CP-8
Locate the desired location for the speaker to be mounted. Check the area for obstructions such
as plumbing, heating ducts or electrical wiring.
Next, locate the wood studs or joists nearest the desired location. Use the supplied speaker
cutout to get the recommended hole dimensions. Position the cutout in the desired location and
outline the speaker opening. If you are not sure of possible obstructions, cut a small hole in the
center of your outline. This will allow you to check for obstructions. If there are no problems
with your mounting location, proceed and cutout the outlined hole.
If the wall or ceiling in not already insulated, we suggest adding insulation, Dacron or some
other sound dampening material. If this material has a foil layer, position the foil away from the
speaker magnet.
Swivel Tweeters
The adjustable, swivel tweeter allows you to point the sound towards or away from the listening
area, depending on the room design and furniture location. If your model includes this feature,
gently push the edge of the tweeter housing to aim the tweeter to the desired area. Be careful not
to damage the tweeter during this procedure.
Setting Level Controls
Tweeter Level control: Some models offers level control for tweeter volume. You can use this
control to get more or less high frequency. Turn the knob to each setting until you get the
desired amount of high frequency. The adjustments are 3dB, 0dB and –3 dB.
Woofer Level control: Some models also offer level control for the bass output of your speaker.
Like the tweeter control, you can adjust the bass volume by turning the knob to each setting until
you get the desired sound. The adjustments are 3dB, 0dB and –3 dB.
If only two channels (R & L) of your amplifier are driving more than one pair of speakers,
TRUAUDIO suggests using the lowest output position for the woofer until you can make sure
the amplifier can handle the additional woofer settings.
We also suggest setting your Tweeter levels first and then matching the bass output to get the
overall sound you desire.
Speaker Installation
Remove the grill from the speaker frame. If needed, carefully push one or two of the dog ear
(mounting legs) mounting screws inward to get the grill off. Attach the speaker wire. Caution:
Make sure to observe polarity (positive + to positive + and negative – to negative -).
When hooking up the amplifier connect the right channel of the amplifier to the right channel of
the speaker. Do the same for the left channel.
Now, turn all the dog ears in toward the speaker. This will allow the speaker to easily fit into
the cut hole. Insert the speaker into the hole making sure to keep the speaker is level. Carefully
tighten the mounting screws evenly to secure the speaker.
As you tighten the screws, the dog ear mounting feet will flip into position to grip into the
drywall. DO NOT over tighten the mounting screws. Once again, check to make sure the
speaker is level. Push on the grill into the grooves in the speaker frame.
Painting the Speaker
If you are going to paint your speakers, we suggest painting them prior to the installation. If you
must paint them while they are still in the wall, remove the grill and replace it with the provided
paint guards. Then you may proceed and paint the frame of the speakers. When painting the
grills, paint them lightly and be careful not to clog the holes. Do not paint the grill while its still
on the speaker, paint them separately.
SoundVision Technologies dba TRUAUDIO Speaker Systems
PRODUCT WARRANTY
All in-wall, in-ceiling, outdoor speakers, volume controls and freestanding
loudspeakers have a lifetime limited warranty. This warranty includes lifetime
parts and repair labor on all components. Powered subwoofers and active
electronics have a one (1) year limited warranty. This warranty includes one (1)
year parts and repair labor on all components. TRUAUDIO’s obligation under this
warranty is limited to repairing or replacing any component found defective in
material or workmanship under normal conditions of use. This warranty shall not
apply to products which have been abused, modified, disassembled, or repaired by
anyone other than TRUAUDIO or one of its appointed service centers. Products to
be repaired under this warranty must be returned to the factory or designated
service center with all transportation and insurance charges pre-paid.
CP-5
Design: 2 way in-ceiling
Woofer: 5 1/4” polypropylene
Tweeter: 3/4” silk dome, swivel
Power: 5 - 60 watts
Impedance: 8 ohms
Frequency Response: 65 - 20K Hz.
Sensitivity: 90 dB (1W/ 1M)
Finish Dimensions: 8 5/8" diameter, 3" D
Cutout Dimensions: 7" diameter
CP-6
Design: 2 way in-ceiling
Woofer: 6 1/2” polypropylene
Tweeter: 3/4” silk dome, swivel
Power: 5 - 80 watts
Impedance: 8 ohms
Frequency Response: 52- 20K Hz.
Sensitivity: 90 dB (1W/ 1M)
Finish Dimensions: 9 1/2" diameter, 3" D
Cutout Dimensions: 8 1/8" diameter
CP-8
Design: 2 way in-ceiling
Woofer: 8" polypropylene
Tweeter: 1" silk dome, swivel
Power: 5 - 100 watts
Impedance: 8 ohms
Frequency Response: 42- 20K Hz.
Sensitivity: 90 dB (1W/ 1M)
Finish Dimensions: 11 1/8" diameter, 3 1/4" D
Cutout Dimensions: 9 3/4" diameter
It is the policy of TRUAUDIO to continuously incorporate improvements into
our products. All specifications are subject to change without notice.
If you have any questions regarding this or any other TRUAUDIO products,
please call 1-888-858-1555, Monday – Friday, 7:00 am – 5:00 pm MST.
TRUAUDIO Speaker Systems, West Valley City, Utah, 84119
Office: 801-746-3777 Fax: 801-746-3774
Model CP-5 • CP-6 • CP-8
Speaker Specifications
Este manual sirve para los siguientes modelos
2
Tabla de contenidos
Otros manuales de Oradores de TRU Audio
TRU Audio
TRU Audio Wraith Series Manual de usuario
TRU Audio
TRU Audio GHT-66P Manual de usuario
TRU Audio
TRU Audio CP-6 Manual de usuario
TRU Audio
TRU Audio GPW-6 Manual de usuario
TRU Audio
TRU Audio XP-5 Manual de usuario
TRU Audio
TRU Audio CL-70v-6UL Manual de usuario
TRU Audio
TRU Audio HARDSCAPE Manual de usuario
TRU Audio
TRU Audio REV6-LCR.1 Manual de usuario
TRU Audio
TRU Audio SAT3 Manual de usuario
TRU Audio
TRU Audio Ghost GP-4 Manual de usuario
TRU Audio
TRU Audio IWP-6 Manual de usuario
TRU Audio
TRU Audio BeatDrop 8 Series Manual de usuario
TRU Audio
TRU Audio B23 series Manual de usuario
TRU Audio
TRU Audio LW Series Manual de usuario
TRU Audio
TRU Audio Phantom Series Manual de usuario
TRU Audio
TRU Audio PAKCROWN Manual de usuario
TRU Audio
TRU Audio Ghost HT Series Manual de usuario
TRU Audio
TRU Audio AS-1 Manual de usuario
TRU Audio
TRU Audio SB-CUSTOM-LC Manual de usuario
TRU Audio
TRU Audio OP-5.2 Manual de usuario
