TRONE Zentina Manual de usuario
Zentina Installation Manual
INSTALLATION PREPARATION
Before installation begins, please confirm that you have the materials
indicated below:
Included
RecommendedTools
Precautions Before Installation
Please give enough allowance for the installation. Ensure that there is
room enough for the opening and closing of the bathroom door. Please
see diagram below for product placement measurements.
Please confirm the location of the sewage outlet and the wax ring as
indicated below before installation.
Installation Requirements
Minimum static water pressure: 20 psi
Maximum static water pressure: 80psi
Minimum water flow: 1 Gallon every 10 seconds
115 V power GFCI receptacle within 4’
#1 INSTALLING THE WATER VALVE
Option #1: Copper Stubbed Out of Wall (easiest method)
1. Shut off water to the house and drain water supply line by
opening a nearby faucet.
2. Once the water pressure has reduced and has stopped flowing,
unscrew the nut from the angle valve and remove the valve
from the copper pipe (stub out).
3. Push the nut as far from the brass crimp ring(ferrule) as possible
and using a wheel cutter or a hacksaw, cut the pipe between
ferrule and the wall (as close to the ferrule as possible)
4. Adapt plumbing to ½” FIP(Female Iron Pipe) with a gasketed
John Guest female adapter (Not included).
https://www.johnguest.com/us/en/cts-fittings/speedfit-twist-
and-lock/elbows/speedfit-female-swivel-elbow-nps-thread
5. Thread Valve onto John Guest fitting and tighten in place (Do
not use Teflon tape)
6. Make sure valve is shut off and turn the water back on to check
for leaks before setting the toilet in place
Option #2: Using PEX water line (new construction, remodels, and
plumber installation. Not recommended without a professional)
1. Shut off water to the house and drain water supply line by
opening a nearby faucet.
2. Once the water pressure has reduced and has stopped flowing,
cut off the valve or fitting using a pipe cutter.
3. Insert a ½” Female gasketed swivel adapter (Not Included) into
the PEX water supply and crimp in place (Crimp ring goes on
first)
https://www.plumbersstock.com/pxfes12-12in-brass-pex-
female-swivel-adapter.html
4. Thread Valve onto fitting and tighten in place (Do not use Teflon
tape)
5. Make sure valve is shut off and turn the water back on to check
for leaks before setting the toilet in place
Option #3: Use existing valve (This method will reduce the water
pressure and volume to the toilet and is not recommended unless one
of the first two options cannot be achieved.)
1. Turn the water off at the toilet valve
2. Flush the toilet two or three times to reduce the amount of
water in the toilet tank
3. Remove (Un-Thread) the supply line from existing toilet.(use a
bowl and towel to catch any access water)
4. Remove the supply line from the existing shut off valve and
replace it with a 3/8” to ½” FIP supply line. (Not Included)
https://www.plumbersstock.com/supb1f09-38inx12x9-flex-
faucet-supply-ss.html
5. Thread new supply line onto the shut-off valve included in the
box and tighten in place. (Do not use Teflon tape)
6. Make sure valve is shut off and turn the water back on to check
for leaks before setting the toilet in place
#2 TOILET INSTALLATION
1. Make a cross mark on the floor drain (see below).
2. Lift the toilet seat, remove the white caps, and remove the
screws. Lift the entire top (lid and seat) from the base of the
toilet.
3. Gently flip the toilet on its side, placing it on the pre-prepared
foam board.
4. Make two marks on the side and front of the toilet
perpendicular to the sewage outlet.
5. Install the wax ring under the toilet.
6. Using two people, lift the toilet and align the marks on the toilet
bowl with the cross marks on the ground. Also confirm the
holes in the bottom of the bowl alighn with the closet bolts.
7. Place the washers over the closet bolts.
8. Use a wrench to lock nuts to the closet bolts.
oWarning! DO NOT OVER TIGHTEN! Over tightening may
crack the porcelain base.
9. Reinstall the top of the toilet back onto the base by tightening
the screws and replacing the white caps.
#3 INSTALLING THE BATTERY
1. Open the battery box and insert battery.
2. Close the battery box and attach the sticker onto one side of the
battery box.
3. Connect the wire.
4. Peel the other side of the sticker and fix it to the side of the
toilet.
#4 CONNECT BRAIDED HOSE
1. Connect the braided hose to the angle valve installed on step 1.
2. After tightening by hand, turn the nut ¼ turn with a wrench.
3. Open the supply stop and check for leaks.
Tabla de contenidos
Otros manuales de Baño de TRONE
TRONE
TRONE Aquatina III A3ETBCERN-12.WH Manual de usuario
TRONE
TRONE Neodoro NETBCERN-12.WH Manual de usuario
TRONE
TRONE Aquatina III A3ETBCERN-12.WH Manual de usuario
TRONE
TRONE Fountina FETBCERN-12.WH Manual de usuario
TRONE
TRONE GANZA II Manual de usuario
TRONE
TRONE Zendoro ZETBCDER-12.WH Manual de usuario
TRONE
TRONE Nobelet NETBCDER-12.WH Manual de usuario
TRONE
TRONE Tahum TETBCERN-12.WH Manual de usuario
TRONE
TRONE Aquatina II A2ETBCERN-12.WH Manual de usuario
Manuales populares de Baño de otras marcas
Better Bathrooms
Better Bathrooms BUN/BeBa 27555/78725 Manual de usuario
American Standard
American Standard CONCEPT Cube TF-2704 Manual de usuario
BIOLAN
BIOLAN ECO Manual de lista de piezas
Thetford
Thetford C260 Series Manual de usuario
KELISS
KELISS T162A Series Manual de usuario
Kohler
Kohler K-22241K Instrucciones de montaje
