TROJAN PRO FORTIS CASES Manual de usuario
FORTIS CASES
Keyboard + fingerprint smart safety case operating instructions
Contents
Product description
Technical parameters
Component names
keyboard + fingerprint smart safety case operating instructions
5 Unlock
6 Add user
7 Modify password
8 Modify and add fingerprints
9 Delete password
10 Delete fingerprint
11 Delete user
12 Check the battery
1 keyboard + fingerprint smart safety case operating instructions
13 Factory data reset
4 Keyboard function setting
2 System basic information setting
3 Prompt setting description buzzer with keyboard LED
14 Cautions
1
1
2
6
7
9
10
12
13
14
15
3
16
5
4
4
16
Product description
Keyboard + fingerprint smart safety case, users can open the case by !
password or fingerprint, each safety case has an administrator, the case!
have password modification, fingerprint modification, add user, delete!
user and other operations. provide comprehensive security service for
the safety case.
Technical parameters
1. Processor: international famous brand with low power consumption
and high-performance processor.
2. Fingerprint identification: inductive fingerprint identification
3. Management level: administrator and ordinary user
4.Storage users: up to 10
5. Fingerprints per user: up to 3
6 charging: type-c USB external charging; Micro USB internal charging!
Battery: 3.7v polymer lithium battery, 8000mAH, no replacement!
Standby time: Up to 2 month
1
Component names
Keyboard + fingerprint smart safety case renderings
2
1
Picture 1: top cover of safety case module
Picture 2: inside cover of safety case module
Micro USB charging
Power switch
S2 function setting button (after the!
administrator unlock the case, enter!
the button for 3 seconds to restore !
factory setting)
keyboard plate
TYPE - C USB charging
Reset button
Fingerprint identification
Keyboard + fingerprint smart safety case operating instructions
Open the top cover of the smart safety case, the keyboard LED
light becomes bright, close the top cover of the smart safety case,
the keyboard LED light is off.
3
1
Picture 1: the normal state of the keyboard Picture 2: keyboard light up
2
Enter the button or touch the fingerprint module and the keyboard
LED lights up. The safety case is not operated within 10 seconds,
the keyboard LED light is off, exit function mode directly.
3
Connect to the power adapter, and the smart safety case will issue
a charging indicate(the keyboard LED light flashes 1 time, and the
buzzer makes 1 long beep). Disconnect the power adapter, and
the safety case will issue a charging indicate (the keyboard LED
light flashes 3 times, and the buzzer makes 3 short beeps).
1
2
3
4
5
6
7
8
9
0
Enter
Cancel
1
2
3
4
5
6
7
8
9
0
Enter
Cancel
#
*
#
*
In any operation of all functional operation, enter the “ ” to exit
the safety case from the functional operation. The keyboard LED
light flashes 3 times and the buzzer makes 3 short beeps.
4
*
System basic information setting
4
1
2
3
4
5
6
The system can save up to 10 user information, numbered 0-9;
User No. 0 is the administrator, and the initial password is 123456.
No. 1-9 is an common user. common users only have rights to
unlock the case and check the battery .
The password can only be a six-digit password, and each user can
save up to three fingerprint information;
Administrator's password can be changed, but can not be deleted;
Input the wrong password (fingerprint) for 5 times continuously !
within 3 minutes, the system will automatically give an alarm, and it!
cannot be operated within 3 minutes;
Setting instructions for buzzer and keyboard LED indicate
1
2
Operation successful indicate - keyboard LED light flashes 1 time, and!
the buzzer makes 1 beep
Operation failure indicate - keyboard LED light flashes 3 times, and!
the buzzer makes 3 short beeps
3
Case not closed alarm - keyboard LED flashing for 2 minutes, the
buzzer beeping for 2 minutes
4
5 consecutive wrong password or fingerprint alarm in 3 minutes --
keyboard LED light flashing for 1 minute,The buzzer honked for a!
minute
Keyboard function setting
5
1
2
3
4
5
6
7
8
9
0
Enter
Cancel
Picture 1: keyboard plate
Picture 2: keyboard function setting table
#
*
Keyboard
Short enter
Long enter (more than 3s)
Enter the number "0"
Enter the number “1"
Enter the number “2”
Enter the number “3”
Enter the number “4”
Enter the number “5”
Enter the number “6”
Enter the number “7”
Enter the number “8”
Enter the number “9”
Return
Confirm
Delete user
Add user /modify password
Add /modify fingerprints
Delete password
Delete fingerprint
Check the battery
Alarm mode
Cancel unclosed case alarm
Factory data reset
（inside）
*
#
Note
Unlock
How to unlock ？
6
1
Enter the correct six-digit password, enter “ #“ to open the safety
case, or enter the correct fingerprint directly to unlock the safety
case.
If the six-digit password is wrong or password with less than six
digits, enter the “ # " ，the case will appear an error indicate.
A
B
Enter the correct fingerprint
Unlock successfully
Unlock successfully
Unlock (two ways)
Enter the correct password ,enter ”# ”
2
11
2
C
If you input the wrong password or fingerprint for 5 times in 3
minutes, the safety case will give an alarm for 1 minute (the
keyboard LED light flashes and the buzzer long beep), and the
safety case cannot be operated within 3 minutes.
7
D
1 minute after the safety case unlocked, if the safety case is not
closed or closed properly, the safety case will alarm and indicate
for 2 minutes (keyboard LED light flashing, buzzer long beep);
During the alarm process, confirm to close the case and the safety
case will stop the alarm; Within 1 minute after the 2-minute alarm
indicate stops, if the safety case is still not closed , the safety
case will give a cyclic alarm indicate. Long press “ ” to cancel
the alarm.
Add user
1
How to add user?
A
The current safety case has an administrator by default , the user
number is “0”, other added user numbers is “1-9”, and the
administrator start codon is "123456". only the administrator has
the permission to use the function of add user.
B
Long press the "1" key for 3 seconds, and with the keyboard LED
light flashing 1 time , the buzzer will make a long beep, and the
safety case will enter the add user mode (add user mode is
consistent with the operation of password modify mode)
*
C
Enter the correct administrator’s password , enter "#" ,or enter the
correct fingerprint directly. If the password and fingerprint are not
correct, the safety case will exit the add user mode.
8
D
E
Enter the user number (1-9) and enter "#" to enter the password
process. The user number takes the last number entered (if the user
enters 1, then 2, and then enter “ #" before the “ # " key is not
entered, the system enters 2 by default)
Enter a six-digit password and enter "#" to enter the new password
again.
F
Enter the new six-digit password repeatedly and enter "#". If the new
password entered twice is consistent, the password will be changed
successfully. Otherwise, the safety case will exit the add user mode.
Long press"1" for 3 seconds
The keyboard LED light flashing for 1 time,
the buzzer will make a long beep
Enter the administrator's correct password ,enter ”# ”or enter the
correct fingerprint directly( Administrator
Enter the 6-digit password ,enter ”# ”
Select user number - add user (1-9) enter ”# ”
2
3
4
5
successfully
6
1
6-digit ,enter ”# ”
‘s start codon is 123456 )
Tabla de contenidos
