Tripp Lite SmartPro SMX2200XLRT2U Manual de usuario

SmartPro®Intelligent,

Line-Interactive

UPS System

Models: SMX2200XLRT2U, SMX3000XLRT2U

(Series Numbers: AG-SM7145, AG-SM7144)

1111 W. 35th Street, Chicago, IL 60609 USA • tripplite.com/support

SmartPro®is a registered trademark of Tripp Lite.

Owner’s Manual

Important Safety Instructions 2

Mounting (Rack) 4

Mounting (Tower) 5

Quick Installation 6

Optional Installation 7

Basic Operation 8

Storage and Service 14

Battery Replacement 15

Regulatory Compliance 15

Español 17

Français 32

Deutsch 47

Русский

SAVE THESE INSTRUCTIONS

This manual contains important instructions and warnings that should be followed during the

installation, operation, maintenance and storage of all Tripp Lite UPS Systems and Batteries.

Failure to heed these warnings may affect your warranty.

UPS Location Warnings

• Use caution when lifting the UPS. Because of the considerable weight of all rack-mount

UPS systems, at least two people should assist in lifting and installing the UPS.

• Your UPS is intended to be used in a temperature-regulated, indoor area that is

relatively free of conductive contaminants, away from excess moisture or heat, dust or

direct sunlight.

• For best performance, the ambient temperature near the UPS should be between 0°C

and 40°C (32°F and 104°F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct

its vents or fan openings.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in

this manner will seriously inhibit the unit's internal cooling, eventually causing product

damage not covered under warranty.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live

even when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS

system’s plug in a way that would eliminate the UPS system’s connection to ground.

Do not use adapters that eliminate the UPS system’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting the UPS to a motor-powered AC generator, the generator must

provide ﬁltered, frequency-regulated computer-grade output.

Explanation of Symbols

Important Safety Instructions

Caution—risk of danger

Electrical shock hazard

Protective earth ground

Recyclable—contains lead

Important Safety Instructions

• Install in accordance with National Electrical Code standards. Be sure to use the proper

overcurrent protection for the installation, in accordance with the plug/equipment rating.

• Branch circuit protection must be provided by building installation. Short-circuit backup

protection and overcurrent protection is provided by the building installation.

• The AC Mains Plug, serves as the disconnect device. The electrical outlets supplying

power to the equipment shall be installed near the equipment and easily accessible.

• Never attempt to install electrical equipment during a thunderstorm.

• Do not attempt to use this equipment if any part of it becomes damaged.

• Do not attempt to modify the UPS, enclosure, input plugs or power cables.

Equipment Connection Warnings

• Do not connect surge suppressors or extension cords to the output of your UPS. This

might overload the UPS and will void the surge suppressor and UPS warranties.

• Individual equipment connected to the UPS must not exceed the maximum nameplate

load rating.

• Use of this equipment in life support applications where failure of this equipment can

reasonably be expected to cause the failure of the life support equipment or to

signiﬁcantly affect its safety or effectiveness is not recommended. Do not use this

equipment within oxygen-enriched atmospheres, or within 0.3 m (1 ft.) of a point at

which an oxygen-enriched atmosphere is intentionally vented.

External Battery Warnings

• Connect external battery ground wire before connecting the external battery

to the UPS.

• Installation is to be performed by qualiﬁed professional electrical service

personnel only.

• Do not connect or disconnect battery modules while the UPS is operating.

• Connect only compatible battery modules.

Battery Replacement and Recycling

Tripp Lite products use sealed lead-acid batteries, which are highly recyclable.

Refer to your local codes for disposal requirements, Call Tripp Lite at

1.773.869.1234 or visit tripplite.com/support/recycling-program for more

information on recycling the batteries or any other Tripp Lite product.

Tripp Lite offers a complete line of UPS System Replacement Battery Cartridges

(R.B.C.).Visit Tripp Lite

Online at tripplite.com/products/battery-ﬁnder/ to locate the speciﬁc replacement

battery for your UPS

Maintenance Warnings

• Your UPS does not contain user-serviceable parts. Do not disassemble.

Mounting (Rack)

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user

must determine the ﬁtness of hardware and procedures before mounting. If hardware

and procedures are not suitable for your application, contact the manufacturer of your

rack or rack enclosure. The procedures described in this manual are for common rack

and rack enclosure types and may not be appropriate for all applications.

4-Post Mounting

All UPS models include hardware required to mount in a 4-post rack. Select models

include an adjustable rack-mount shelf kit to provide additional support. If your UPS

model does not include an adjustable rack-mount shelf kit, skip steps 1 and 2.

Connect the two segments of each shelf A

using the included screws and nuts B.

Leave the screws slightly loose so that the

shelves can be adjusted in the next step.

Adjust each shelf to ﬁt your rack, then mount

them in the lowest available space of your

rack with the screws, nuts and washers

provided C. Note that the support ledges

should face inward. Tighten the screws that

connect the shelf segments B.

Attach mounting ears Dto the front mounting

holes of your equipment Eusing the screws

provided F. The ears should face forward.

Using an assistant if necessary, lift your

equipment and slide it onto the mounting

shelves. Attach your equipment to the rack

by using the appropriate hardware Gthrough

its mounting ears and into the rack rails.

D F

Stand your UPS on its side with the LED/

Control panel at the top. Attach one rack

mounting ear Ato each side of the UPS

using included screws B. Attach the rack

mounting ears to the ﬂoor with

user-supplied hardware.

Rotate the LED/Control panel to view it

easier while the UPS is tower mounted.

Insert a small screwdriver, or other tool,

in the slots on either side of the panel.

Pop the panel out; rotate it; and pop the

panel back in place.

Note: For additional stability, order the 2-9USTAND

expandable tower stand accessory.

Mounting (Tower)

2-Post (Telecom) Mounting

Two-post mounting will require a Tripp Lite 2-Post Rack-Mount Installation Kit (Model

2POSTRMKITWM, sold separately). For detailed installation procedures, see the

2POSTRMKITWM Owner's Manual.

Mount all UPS models in an upright, tower position using included hardware. The user

must determine the ﬁtness of hardware and procedures before mounting.

Insert a user-supplied power cord

(with country-speciﬁc plug) into the

UPS System's IEC-320-C20 AC input

receptacle. Plug the cord into an AC

wall outlet.*

NOTE! after you plug the UPS into a live AC

outlet, the UPS (in “Standby” mode) will

automatically charge its batteries,** but

will not supply power to its outlets until it is

turned ON.

* See the UPS system nameplate for input requirements.

** The BATTERY CHARGE LED will be the only LED

illuminated.

Find one of the C13-to-C14 power

cords that came with the UPS.

Insert the cord’s female plug into

your computer’s AC input. Insert

the cord’s male plug into any UPS

female output receptacle.

Plug your equipment into the UPS.*

Plug your equipment into the UPS. Repeat

the previous step, using the additional

power cord(s) included with the UPS

system.

Note: Additional interconnection cords

(C13-to- C14) are available from Tripp Lite.

Call +1.773.869.1234 (Part # P004-006).

* Your UPS is designed to support computer equipment

only. You will overload the UPS if the total VA ratings

for all the equipment you connect exceeds UPS output

capacity. To ﬁnd your equipment’s VA ratings, look on

their nameplates. If the equipment is listed in amps,

multiply the number of amps by 230 to determine VA.

(Example: 1 amp × 230 = 230 VA).

If you are unsure if you have overloaded your UPS

system's outlets, see “OUTPUT LOAD LEVEL” LED

description.

Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY”

button for one second. The alarm will beep

once brieﬂy after one second has passed.

Release the button.

Quick Installation

USB and RS-232 Serial

Communications

Use the included USB cable (see 1a ) and/

or DB9 serial cable (see 1b ) to connect

the communication port on your computer

to the communication port of your UPS.

Install on your computer the Tripp Lite

PowerAlert Software appropriate to your

computer’s operating system.

EPO Port Connection

This optional feature is only for those

applications which require connection to

a facility’s Emergency Power Off (EPO)

circuit. When the UPS is connected to this

circuit, it enables emergency shutdown of

the UPS system's inverter.

Using the cable provided, connect the

EPO port of your UPS (see 2a ) to a user-

supplied normally closed or normally open

switch according to the circuit diagram

(see 2b ). The EPO port is not a phone line

surge suppressor; do not connect a phone

line to this port.

External Battery Connection

Your UPS comes with a robust internal

battery system; external batteries are

needed only to extend runtime. Adding

external batteries will increase recharge

time as well as runtime.

The illustration (see 3a) shows the location

of your UPS system's External Battery

Connector, where you will insert the

battery pack cable. Complete installation

instructions for your battery pack appear

in the battery pack owner’s manual. Make

sure that cables are fully inserted into their

connectors. Small sparks may result during

battery connection; this is normal.

Optional Installation

These connections are optional. Your UPS will

function properly without these connections.

4-5

“ON/OFF/STANDBY” Button

To turn the UPS ON: with the UPS plugged into a live AC wall outlet*,

press and hold the “ON/OFF/STANDBY” button for one second.**

Release the button. If utility power is absent, you can “cold-start”

the UPS (i.e.: turn it ON and supply power for a limited time from its

batteries***) by pressing and holding the “ON/OFF/STANDBY” button for

one second.**

To turn the UPS OFF: with the UPS ON and receiving utility power, press

and hold the “ON/OFF/STANDBY” button for one second.** Then unplug

the UPS from the wall outlet. The UPS will be completely OFF.

* After you plug the UPS into a live AC outlet, the UPS (in ”Standby” mode) will automatically

charge its batteries, but will not supply power to its outlets until it is turned ON. ** The alarm

will beep once brieﬂy after the indicated interval has passed. *** If fully charged.

“MUTE/TEST” Button

To Silence (or “Mute”) UPS Alarms: brieﬂy press and release the

MUTE/TEST button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and

hold the MUTE/TEST button. Continue holding the button until the alarm

beeps several times and the UPS performs a self test. See “Results of a

Self-Test” below. Note: you can leave connected equipment on during a

self-test. Your UPS, however, will not perform a self-test if the UPS is

not turned on (see “ON/OFF/STANDBY” Button description).

Basic Operation

Do not connect or disconnect battery packs

when the UPS is running on battery power.

If you connect any external batteries, set

the Battery Charge Level Switches (see 3b )

to the down position. This will increase your

UPS system's charger output so that the

additional batteries charge faster. 3b

Buttons (Front Panel)

Caution!

DO NOT set the Battery Charge Level Switches to the down position

without an external battery connected. There is a risk of damaging

the UPS system's internal battery system.

Basic Operation

CAUTION!

Do not unplug your UPS to test its batteries. This will

remove safe electrical grounding and may introduce a

damaging surge into your network connections.

Results of a Self-Test: The test will last approximately 10 seconds as

the UPS switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm

continues to sound after the test, the UPS system's outlets are

overloaded. To clear the overload, unplug some of your equipment

and run the self-test repeatedly until the “OUTPUT LOAD LEVEL” LED

is no longer lit red and the alarm is no longer sounding.

CAUTION!

Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and

cease supplying output power in the event of a blackout

or brownout.

• If the “BATTERY WARNING” LED remains lit and the alarm continues

to sound after the test, the UPS batteries need to be recharged or

replaced. Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED remains lit, contact Tripp Lite for

service. If your UPS requires battery replacement, visit tripplite.com

to locate the speciﬁc Tripp Lite replacement battery for your UPS.

Basic Operation

All Indicator Light descriptions apply when the UPS is plugged into a

wall outlet and turned ON.

“POWER” LED: this green LED lights continuously when the UPS is

ON and supplying connected equipment with AC power from a utility

source. The LED ﬂashes and an alarm sounds (4 short beeps followed

by a pause) to indicate the UPS is operating from its internal batteries

during a blackout or severe brownout. If the blackout or severe

brownout is prolonged, you should save ﬁles and shut down your

equipment since internal battery power will eventually be depleted.

See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED lights continuously

whenever the UPS is automatically correcting high or low AC voltage

on the utility line without the assistance of battery power. The UPS

will also emit a slight clicking noise. These are normal, automatic

operations of the UPS, no action is required on your part.

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the

approximate electrical load of equipment connected to the UPS

system's AC outlets. It will turn from green (light load) to yellow

(medium load) to red (overload). If the LED is red (either illuminated

continuously or ﬂashing), clear the overload immediately by

unplugging some of your equipment from the outlets until the LED

changes from red to yellow (or green). CAUTION! Any overload that

is not corrected by the user immediately may cause the UPS to shut

down and cease supplying output power in the event of

a blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility

power, this LED indicates the approximate charge state of the UPS

system's internal batteries: red indicates the batteries are beginning

to charge; yellow indicates the batteries are roughly midway through

charging; and green indicates the batteries are fully charged. When

the UPS is operating from battery power during a blackout or severe

brownout, this LED indicates the approximate amount of energy

(ultimately affecting runtime) which the UPS system's batteries will

provide: red indicates a low level of energy; yellow indicates a medium

level of energy; and green indicates a high level of energy. Since the

runtime performance of all UPS batteries will gradually deplete over

time, it is recommended that you periodically perform a self-test (see

MUTE/TEST Button description) to determine the energy level of your

UPS batteries BEFORE a blackout or severe brownout occurs. During

a prolonged blackout or severe brownout, you should save ﬁles and

shut down your equipment since battery power will eventually be

Indicator Lights (Front Panel)

Otros manuales para SmartPro SMX2200XLRT2U

Este manual sirve para los siguientes modelos

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartPro SMART1000RM1U Manual de usuario

Tripp Lite

Tripp Lite AVRX550U Manual de usuario

Tripp Lite

Tripp Lite OmniSmart OMNI700ISO Manual de usuario

Tripp Lite

Tripp Lite AVR750U Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU2200RTXL2UA Manual de usuario

Tripp Lite

Tripp Lite SMART550USBTAA Manual de instalación y operación

Tripp Lite

Tripp Lite ECO350UPS Manual de usuario

Tripp Lite

Tripp Lite HT850UPS Manual de usuario

Tripp Lite

Tripp Lite SmartPro Rackmount Manual de usuario

Tripp Lite

Tripp Lite INTERNET OFFICE 300 Guía del usuario

Tripp Lite

Tripp Lite Digital UPS Systems Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU1500LCD1U Manual de usuario

Tripp Lite

Tripp Lite TM500 Manual de usuario

Tripp Lite

Tripp Lite AGOM5516 Manual de usuario

Tripp Lite

Tripp Lite UPS System AVRX750U Manual de usuario

Tripp Lite

Tripp Lite SMART 2200 NET Manual de usuario

Tripp Lite

Tripp Lite AVRT450U Manual de usuario

Tripp Lite

Tripp Lite Internet Office Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART700 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU750RTXL2U Manual de usuario

Tripp Lite

Tripp Lite SmartOnline 5KVA Manual de usuario

Tripp Lite

Tripp Lite SmartPro Series Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART1050XL Manual de usuario

Tripp Lite

Tripp Lite SmartOnline AGPS8294 Series Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario