Tripp Lite SmartPro 3U Manual de usuario

1111 W. 35th Street, Chicago, IL 60609 USA

www.tripplite.com/support

Important Safety Instructions 2

Mounting 3

Quick Installation 4

Basic Operation 6

Storage and Service 11

SmartPro®3U Rackmount (5000VA)

Intelligent, Line-Interactive UPS Systems

• 208V Input, 120/208V Sine-Wave Output

• Extended Runtime on Select Models

Not suitable for mobile applications.

Warranty Registration 11

Optional Installation 5

Owner’s Manual

WARRANTY

REGISTRATION

to win a FREE Tripp Lite product!

www.tripplite.com/warranty

Español 13

Français 24

Battery Replacement 12

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 1

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation, operation

and storage of all Tripp Lite UPS Systems. Failure to heed these warnings will void your warranty.

UPS Location Warnings

• Use caution when lifting UPS. Because of the considerable weight of all Rackmount UPS

systems, at least two people should assist in lifting and installing them.

• Install your UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near your UPS should be between 0° C and

40° C (between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its

vents or fan openings.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even

when the UPS is not connected to an AC supply.

• Connect your UPS to a properly grounded AC power outlet. Do not modify the UPS’s plug

in a way that would eliminate the UPS's connection to ground. Do not use adapters that

eliminate the UPS’s connection to ground.

• Do not plug your UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting your UPS to a motor-powered AC generator, the generator must provide

filtered, frequency-regulated computer-grade output. Connecting your UPS to a generator will

void its Ultimate Lifetime Insurance.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support applications in which a malfunction or

failure of a Tripp Lite UPS System could cause failure or significantly alter the performance

of a life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This might

overload the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS. Battery replacement should be performed only by authorized service

personnel using the same number and type of batteries (sealed Lead-Acid). The batteries are

recyclable. Refer to your local codes for disposal requirements or in the USA only call

1-800-SAV-LEAD or 1-800-8-BATTERY (1-800-8-228-8379) or visit www.rbrc.com for

recycling information. Tripp Lite offers a complete line of UPS System Replacement Battery

Cartridges (R.B.C.). Visit Tripp Lite on the Web at www.tripplite.com to locate the specific

replacement battery for your UPS.

• During hot-swap battery replacement, the UPS will not provide backup power in the event of

a blackout or other power interruptions.

• Do not operate UPS without batteries.

• When adding external battery packs, connect only Tripp Lite-recommended battery packs of the

correct voltage and type. Do not connect or disconnect battery packs when the UPS is

operating on battery power.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 2

Mounting

Mount your equipment in either a 4-post or 2-post rack or rack enclosure. The user must determine

the fitness of hardware and procedures before mounting. If hardware and procedures are not suitable

for your application, contact the manufacturer of your rack or rack enclosure. The procedures

described in this manual are for common rack and rack enclosure types and may not be appropriate

for all applications.

4-Post Rackmount Installation

Loosen the wingnuts on each of the two adjustable

side supports ; adjust the length of the supports to

match the depth of your rack; tighten wingnuts. Mount

both side supports in the lowest space of your rack on

the inside surfaces of the rails with user-supplied

#10-32 rack bolts and washers . Note: Both support

ledges should face inward. The side supports’ front

and back holes are threaded and do not require nuts to

secure rack bolts.

Attach mounting ears to the front mounting holes

of your equipment using the screws provided .

The ears should face forward.

Using an assistant if necessary, lift your equipment

and slide it onto the mounting shelves. Attach your

equipment to the rack by using the appropriate

hardware through its mounting ears and into the

rack rails.

2-Post Rackmount Installation

If you mount this UPS model in 2-post racks, it requires the

addition of a Tripp Lite 2-Post Rackmount Installation Kit

(model: 2POSTRMKIT, sold separately). See Installation Kit

owner's manual for installation procedure.

Tower Installation

If you tower mount this UPS, it requires the addition of a

Tripp Lite 2U to 9U tower stand (model: 2-9USTAND,

sold separately). See owner's manual for installation procedure.

Rotate the power module’s Control Panel to view it easier

while the UPS is tower mounted. Insert a small screwdriver,

or other tool, in the slots on either side of the Control Panel.

Pop the panel out; rotate it; and pop the panel back into place.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 3

Quick Installation

Plug the UPS into an outlet on a

dedicated circuit.*

NOTE! after you plug the UPS into a live AC outlet,

the UPS (in “Standby” mode) will automatically

charge its batteries,** but will not supply power to

its outlets until it is turned ON (see Step 3 below).

* Select models include an additional plug which can be switched by

a qualified electrician. ** The BATTERY CHARGE LED will be the

only LED illuminated.

Plug your equipment into the UPS.*

* Your UPS is designed to support only electronic equipment. You will

overload the UPS if the total VA ratings for all the equipment you

connect exceeds the UPS's Output Capacity. To find your equipment's

VA ratings, look on their nameplates. If the equipment is listed in

amps, multiply the number of amps by 120 to determine VA. (Example:

1 amp × 120 = 120 VA). If you are unsure if you have overloaded the UPS's

outlets, see “OUTPUT LOAD LEVEL” LED description.

Turn the UPS ON.

Press and hold the “ON/OFF/STANDBY” button for

one second. The alarm will beep once briefly after one

second has passed. Release the button.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 4

Optional Installation

These connections are optional. Your UPS will function

properly without these connections. Note: Your unit may differ

slightly from these diagrams.

USB and RS-232 Serial

Communications

Use the included USB cable (see ) and/or DB9 serial

cable (see ) to connect the communication port on

your computer to the communication port of your

UPS. Install on your computer the Tripp Lite

PowerAlert Software appropriate to your computer’s

operating system. Your UPS may feature additional

communications ports; these ports may also be connected

to additional computers which have PowerAlert

Software installed. Consult your PowerAlert manual

for more information.

Relay Contact-Closure Connection

Use the included DB9 cable (see ) to connect

specialized electronic equipment to the relay

contact-closure port on your UPS System.See diagram

( ) and chart below to determine signals carried by

this port.

Relay Contact Closure Chart

4-5

LINE FAIL

K1 A

LO BATT

K1 0A

OPENS ON LI NE FA IL

CLOSE S ON LI NE FAIL

CLOS ES BE LOW L OW BAT TER Y

TOP OF DUAL

DB9 (J5/J34)

NO TE :

CLOSES BE LO W MID B AT TER Y

REMO T E CO NTA C TS

COM

MID BAT

K4 A

COM

OPENS

BELOW MID BATT ER Y

RE LAYS SH OW N D E -E NE RG IZ ED

OPENS BELOW LOW BATTERY

Relay Contact Closure Interface Diagram

EPO Port Connection (Select Models Only)

This optional feature is only for those applications

which require connection to a facility’s Emergency

Power Off (EPO) circuit. When the UPS is connected to

this circuit, it enables emergency shutdown of the

UPS’s inverter.

Using the cable provided, connect the EPO port of your

UPS (see ) to a user-supplied normally closed or nor-

mally open switch according to the circuit diagram (see

). The EPO port is not a phone line surge suppressor;

do not connect a phone line to this port.

Line Fail Mid Battery Low Battery

Indication Indication Indication

UPS Operating Pins 1 Pins 2 Pins 7 Pins 8 Pins 4 Pins 5

Conditions & 6 & 6 & 3 & 3 & 9 & 9

AC Input Voltage OK CLOSED OPEN — — — —

AC Input Out of Range OPEN CLOSED — — — —

Battery More than 3 Min. — — OPEN CLOSED — —

Remaining Charge*

Battery Less than 3 Min. — — CLOSED OPEN — —

Remaining Charge*

Battery More than 2 Min. — — — — OPEN CLOSED

Remaining Charge*

Battery Less than 2 Min. — — — — CLOSED OPEN

Remaining Charge*

Open on Close on Close Open Close Open

Line Line Below Below Below Below

Contact Action Failure Failure Mid Mid Low Mid

Battery Battery Battery Battery Battery

* Times are approximate, at full load.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 5

“ON/OFF/STANDBY” Button: When the UPS system is connected to a live

AC utility power source, the UPS System will operate in one of three modes:

ON, OFF or STANDBY. Refer to the chart below for UPS System operating

characteristics within each mode.

UPS Charges Battery UPS Supplies Power to Outlets

Mode (when utility is present) (when utility is present or absent*) UPS Displays LEDs

ON Yes Yes Yes (variety of LEDs,

depending on conditions)

OFF No No No

STANDBY Yes No Yes ("BATTERY CHARGE"

LED only)

To place the UPS in the ON mode: Once the utility power source is live, the

UPS System will automatically enter STANDBY mode. Press and hold the

"ON/OFF/STANDBY" button for one second** and then release it to switch

the UPS System from STANDBY mode to ON mode.

OPTIONAL: If the utility power source is not live, you can "cold-start" the

UPS System (i.e.: switch it directly from the OFF mode to the ON mode by

supplying power for a limited time from its batteries*) by pressing and holding

the "ON/OFF/STANDBY" button for one second** and then releasing it.

To place the UPS in the OFF mode: With the UPS System in the ON mode and

receiving utility power, press and hold the "ON/OFF/STANDBY" button for one

second** and then release it to switch the UPS System from ON mode to STANDBY

mode. Then, unplug the UPS from the wall outlet. The UPS will be completely OFF.

* If batteries are fully charged. ** The alarm will beep once briefly after the interval has passed.

Basic Operation

Buttons (Front Panel)

If you connect any external batteries, set the Battery

Charge Level Switch (see ) to the down position.

This will increase your UPS’s charger output so the

additional batteries charge faster. Note: the switch to

the right of the Battery Charge Level Switch is inactive

and will not affect UPS operation regardless of its position.

CAUTION! DO NOT set the Battery Charge Level Switch to the

down position without an external battery connected. There is a

risk of damaging the UPS’s internal battery system.

Optional Installation

continued

External Battery Connection

(Select Models Only)

Your UPS comes with a robust internal battery system;

external batteries are only needed to extend runtime.

Adding external batteries will increase recharge time as

well as runtime.

The illustration (see ) shows the location of your

UPS’s External Battery Connector, where you will

insert the battery pack cable. Complete installation

instructions for your battery pack appear in the battery

pack’s owner’s manual. Make sure that cables are fully

inserted into their connectors. Small sparks may result

during battery connection; this is normal.

Do not connect or disconnect battery packs when the

UPS is running on battery power.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 6

“MUTE/TEST” Button

To Silence (or “Mute”) UPSAlarms: briefly press and release the MUTE/TEST button.*

To Run a Self-Test: with your UPS plugged in and turned ON, press and hold

the MUTE/TEST button for two seconds.* Continue holding the button until

the alarm beeps several times and the UPS performs a self test. See “Results of

a Self-Test” below. Note: you can leave connected equipment on during a self-test.

Your UPS, however, will not perform a self-test if the UPS is not turned on (see

“ON/OFF/STANDBY” Button description).

CAUTION! Do not unplug your UPS to test its batteries. This will remove

safe electrical grounding and may introduce a damaging surge into your

network connections.

Results of a Self-Test: The test will last approximately 10 seconds as the

UPS switches to battery to test its load capacity and battery charge.

• If the “OUTPUT LOAD LEVEL” LED remains lit red and the alarm continues

to sound after the test, the UPS’s outlets are overloaded. To clear the overload,

unplug some of your equipment and run the self-test repeatedly until the

“OUTPUT LOAD LEVEL” LED is no longer lit red and the alarm is no

longer sounding.

* The alarm will beep once briefly after the indicated interval has passed.

CAUTION! Any overload that is not corrected by the user immediately

following a self-test may cause the UPS to shut down and cease supplying

output power in the event of a blackout or brownout.

• If the “BATTERY WARNING” LED remains lit and the alarm continues

to sound after the test, the UPS batteries need to be recharged or replaced.

Allow the UPS to recharge continuously for 12 hours, and

repeat the self-test. If the LED remains lit, contact Tripp Lite for service.

If your UPS requires battery replacement, visit www.tripplite.com to

locate the specific Tripp Lite replacement battery for your UPS.

Basic Operation

continued

Buttons (Front Panel)

Indicator Lights (Front Panel)

All Indicator Light descriptions apply when the UPS is plugged into a wall outlet

and turned ON.

“POWER” LED: this green LED lights continuously when the UPS is ON and

supplying connected equipment with AC power from a utility source. The LED

flashes and an alarm sounds (4 short beeps followed by a pause) to indicate the

UPS is operating from its internal batteries during a blackout or severe

brownout. If the blackout or severe brownout is prolonged, you should save

files and shut down your equipment since internal battery power will eventually

be depleted. See “BATTERY CHARGE” LED description below.

“VOLTAGE CORRECTION” LED: this green LED lights continuously

whenever the UPS is automatically correcting high or low AC voltage on the

utility line without the assistance of battery power. The UPS will also emit a

slight clicking noise. These are normal, automatic operations of the UPS, no

action is required on your part.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 7

Basic Operation

continued

Indicator Lights (Front Panel)

“OUTPUT LOAD LEVEL” LED: this multicolored LED indicates the

approximate electrical load of equipment connected to the UPS's AC outlets. It

will turn from green (light load) to yellow (medium load) to red (overload). If

the LED is red (either illuminated continuously or flashing), clear the overload

immediately by unplugging some of your equipment from the outlets until the

LED changes from red to yellow (or green). CAUTION! Any overload that is

not corrected by the user immediately may cause the UPS to shut down and

cease supplying output power in the event of a blackout or brownout.

“BATTERY CHARGE” LED: when the UPS is operating from utility power,

this LED indicates the approximate charge state of the UPS's internal batteries:

red indicates the batteries are beginning to charge; yellow indicates the batteries

are roughly midway through charging; and green indicates the batteries are fully

charged. When the UPS is operating from battery power during a blackout or

severe brownout, this LED indicates the approximate amount of energy

(ultimately affecting runtime) which the UPS’s batteries will provide: red

indicates a low level of energy; yellow indicates a medium level of energy; and

green indicates a high level of energy. Since the runtime performance of all UPS

batteries will gradually deplete over time, it is recommended that you

periodically perform a self-test (see MUTE/TEST Button description) to

determine the energy level of your UPS batteries BEFORE a blackout or severe

brownout occurs. During a prolonged blackout or severe brownout, you should

save files and shut down your equipment since battery power will eventually be

depleted. When the LED turns red and an alarm sounds continuously, it indicates

the UPS's batteries are nearly out of power and UPS shut down is imminent.

“BATTERY WARNING” LED: this LED lights red and an alarm sounds

intermittently after you initiate a self test (See “MUTE/TEST” Button description)

to indicate the UPS batteries need to be recharged or replaced. Allow the UPS to

recharge continuously for 12 hours, and repeat the self-test. If the LED

continues to light, contact Tripp Lite for service. If your UPS requires battery

replacement, visit www.tripplite.com to locate the specific Tripp Lite

replacement battery for your UPS.

AC Receptacles: Your UPS features 15/20-amp AC outlets and 20-amp and

30- amp AC outlets. These output receptacles provide your connected

equipment with AC line power during normal operation and battery power during

blackouts and brownouts. The UPS protects equipment connected to these

receptacles against damaging surges and line noise. If you have a serial or USB

connection to your UPS, you can remotely reboot connected equipment by turning

the receptacles OFF and ON using Tripp Lite's PowerAlert Software. Select

models have their receptacles divided into one or more load banks (labelled

“LOAD 1,” etc.) which may be remotely switched OFF and ON

using Tripp Lite UPS software without interrupting power to

equipment connected to the other outlets.

Other UPS Features (Rear Panel)

15/20 amp (120V)

NEMA 5-15/20R

30 amp (208V)

NEMA L6-30R

20 amp (208V)

NEMA L6-20R

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 8

Basic Operation

continued

Other UPS Features (Rear Panel)

Communications Ports (USB or RS-232): These ports connect your UPS to any

workstation or server. Use with Tripp Lite’s PowerAlert Software and included

cables to enable your computer to automatically save open files and shut down

equipment during a blackout. Also use PowerAlert Software to monitor a wide

variety of AC line power and UPS operating conditions. Consult your

PowerAlert Software manual or contact Tripp Lite Customer Support for more

information. See “Optional Installation” section for installation instructions.

Relay Contact Interface Port: This female DB9 port sends contact-closure

signals to indicate line-fail and low battery status. See “Optional Installation”

section for installation instructions.

EPO (Emergency Power Off) Port (Select Models Only): Your UPS features

a EPO port that may be used to connect the UPS to a contact closure switch to

enable emergency inverter shutdown. See Optional Installation.

Accessory Slot: Remove the small cover panel from this slot to install optional

accessories to remotely monitor and control your UPS. Refer to your accessory’s

manual for installation instructions. Contact Tripp Lite Customer Support at

(773) 869-1234 for more information, including a list of available SNMP, network

management and connectivity products.

Power Sensitivity Adjustment: This dial is normally set fully counter-clockwise,

which enables the UPS to provide maximum protection against waveform

distortions in its AC input. When such distortion occurs, the UPS will normally

switch to providing sine wave power from its battery reserves for as long as the

distortion is present. In areas with poor utility power or where the UPS’s input

power comes from a backup generator, chronic waveform distortion could

cause the UPS to switch to battery too frequently, draining its battery reserves.

You may be able to reduce how often your UPS switches to battery due to

moderate waveform distortion by experimenting with different settings for this

dial. As the dial is turned clockwise, the UPS becomes more tolerant of

variations in its input power’s AC waveform. NOTE: The further the dial is

adjusted clockwise, the greater the degree of waveform distortion the UPS will

allow to pass to connected equipment. When experimenting with different

settings for this dial, operate connected equipment in a safe test mode so that the

effect on the equipment of any waveform distortions in the UPS’s output can be

evaluated without disrupting critical operations.

External Battery Connector (Select Models Only): Use to connect Tripp Lite

external battery packs for additional runtime. Refer to instructions available with

the battery pack for complete connection information and safety warnings.

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 9

Basic Operation

continued

Battery Charge Level Switch (Select Models Only): Controls the UPS

system's battery charge rate. If you connect any external batteries, set the

Battery Charge Level Switch to the down position. This will increase your

UPS's charger output so the additional batteries charge faster. Note: the switch

to the right of the Battery Charge Level Switch is inactive and will not affect

UPS operation regardless of its position. CAUTION! DO NOT set the Battery

Charge Level Switch to the down position without an external battery

connected. There is a risk of damaging the UPS's internal battery system.

Output Breakers (Select Models Only): Your UPS has two kinds of breakers

that protect your UPS from output overload. If the breaker switch trips, remove

some of the load from the UPS’s 20-amp receptacles and allow the unit to cool

before resetting the breaker switch by flipping it from off to on. If the breaker

button trips, remove some of the load on the UPS’s 15/20-amp receptacles and

allow the unit to cool before resetting the breaker button by pressing it.

Ground Screw: Use this to connect any equipment that requires a chassis ground.

Charge Rate Setting

(when External

Batteries are

connected)

Charge Rate Setting

(when External

Batteries are not

connected)

201112103 93-2459.qxd 1/9/2012 12:21 PM Page 10

Otros manuales para SmartPro 3U

Tabla de contenidos

Idiomas:

Otros manuales de Unión Postal Universal de Tripp Lite

Tripp Lite

Tripp Lite SmartPro Series Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU30K3/3 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU20K3/3 Manual de usuario

Tripp Lite

Tripp Lite SMX Series Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU6000RT4UHVHW Guía de instalación

Tripp Lite

Tripp Lite SmartOnline SU3000XLNAFTA Manual de usuario

Tripp Lite

Tripp Lite SmartPro 1050RM Instrucciones de instalación y funcionamiento

Tripp Lite

Tripp Lite AGOM8265 Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU8000RT3UN50 Manual de usuario

Tripp Lite

Tripp Lite SmartPro Datacenter INT Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU1500XL Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMX700HG Manual de usuario

Tripp Lite

Tripp Lite SMX1000LCD Manual de usuario

Tripp Lite

Tripp Lite VS450T Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU2200XLNAFTA Manual de usuario

Tripp Lite

Tripp Lite SmartPro 2U 1400-3000 VA Manual de usuario

Tripp Lite

Tripp Lite TE600 Manual de usuario

Tripp Lite

Tripp Lite INTERNET550U Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART1500 Manual de usuario

Tripp Lite

Tripp Lite SmartPro SMART3000RMXL2U Guía de instalación

Tripp Lite

Tripp Lite OMNIPOWER PRO550 Manual de usuario

Tripp Lite

Tripp Lite LCDT Series Manual de usuario

Tripp Lite

Tripp Lite SmartOnline SU3000RTXR3UHW Guía de instalación

Tripp Lite

Tripp Lite ECO-UPS ECO850LCD Manual de usuario

Manuales populares de Unión Postal Universal de otras marcas

Pylontech

Pylontech Victron & Pylontech US5000 Manual de usuario

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manual de usuario

Mecer

Mecer ME-1000-WTU Manual de usuario

Mustek

Mustek PowerMust 530(B) Plus Manual de instalación y operación

Emerson

Emerson Liebert NXL series Manual de usuario

MAKELSAN

MAKELSAN BOXER SERIES Manual de usuario

Block

Block PC-0524-400-0 Manual de usuario

CyberPower

CyberPower CP585LCD Manual de usuario

Eaton

Eaton 3S Instrucciones de montaje

CyberPower

CyberPower Office Tower Series UPS 1000 Manual de usuario

CyberPower

CyberPower BM100 Manual de usuario

Best Power

Best Power 610 Manual de usuario

Best Power

Best Power Unity/I UT3K Manual de usuario

Mustek

Mustek PowerMust 400 Offline Manual de usuario

Xantrex

Xantrex Trace 512 UR-UPS Manual de usuario

Forza

Forza SL-1501UL Manual de usuario

LEGRAND

LEGRAND keor 310081 Manual de usuario

ABB

ABB Conceptpower DPA 500 Manual de usuario