Tripp Lite U357-025-2 Manual de usuario
1
Owner’s Manual
Dual-Bay USB 3.0 to SATA
Portable Hard Drive
RAID Enclosure
Model: U357-025-2
Español 7 • Français 13 • Русский 19
PROTECT YOUR INVESTMENT!
Register your product for quicker service
and ultimate peace of mind.
You could also win an ISOBAR6ULTRA
surge protector—a $100 value!
www.tripplite.com/warranty
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Copyright © 2017 Tripp Lite. All rights reserved.
17-02-025-93368C.indb 1 2/6/2017 5:02:56 PM
2
Package Contents
System Requirements
Product Features
• U357-025-2
• USB 3.0 A to Micro-B Device Cable, 2 ft.
• USB A to Micro-B Power Cable, 2 ft.
• Owner’s Manual
• (2) 2.5 in. SATA hard drives (maximum height 0.4 in. [9.5 mm])
• Computer with available USB port (USB 3.0 port required to achieve
USB 3.0 speeds)
• Any USB-enabled operating system
• Converts any two 2.5 in. SATA drives up to 2 TB for connection to
your computer’s USB port
• Features RAID 0, RAID 1 and JBOD disk modes for flexible access to
your data
• Portable tool-free design for quick on-the-go external storage
• Supports data transfer rates up to 5 Gbps
• Backward compatible with previous USB generations
• Compatible with SATA I (1.5 Gbps), SATA II (3 Gbps) and SATA III
(6 Gbps) drives
• UASP-compatible for performance up to 70% faster
• Plug and play—no software or drivers required
17-02-025-93368C.indb 2 2/6/2017 5:02:56 PM
3
Optional Accessories
Installation
• U324-Series USB 3.0 SuperSpeed Extension Cable A to A (M/F)
• U326-Series USB 3.0 SuperSpeed Device Cable A to Micro-B (M/M)
• U280-002-W12 USB Wall Charger
Notes:
• HDD/SSD drives are sensitive to static electricity and must be handled carefully
so as not to risk data loss. Always handle an HDD/SSD drive with caution by
wearing an anti-static strap (such as Tripp Lite’s P999-000) when transporting
it or by touching a grounded metal surface to discharge yourself of static
electricity before touching the drive.
• If your SATA drive has not been formatted, you must do so using your
computer’s Disk Management Utility in order to copy and access files.
• Before unplugging the enclosure, properly eject the drive from your computer
to avoid potential data loss.
1. Make sure the Lock/Unlock button on the bottom of the unit is
switched to Unlock.
2. Slide the covers away from each side of the enclosure to reveal the
double-sided drive tray.
3. Slide a 2.5-inch HDD/SSD into each drive tray.
4. Line up the SATA plug on the drives to the SATA reciprocals on each
drive tray.
5. Slide the covers back onto each side of the enclosure.
6. Switch the Lock/Unlock button to Lock.
7. Set the RAID configuration. See the RAID Mode section and table
for instructions on how to do this.
17-02-025-93368C.indb 3 2/6/2017 5:02:56 PM
4
Installation
8. After changing the DIP switches as desired, hold down the Reset
button until the LEDs quickly blink. If successful, the LED next to the
chosen setting will stay on.
9. Power on the unit by connecting the included USB 2.0 power cable
between the DC In port and your computer’s USB port or a USB
charger.
10.Connect the included USB 3.0 cable between the unit’s USB port
and the host computer’s USB port.
11.The unit is now ready to use.
RAID Mode
This unit can be set to function in one of three modes: JBOD, RAID1 or
RAID2. Each mode is described below along with their corresponding
DIP switch setting.
RAID Mode Description DIP Switch 1 DIP Switch 2
JBOD Allows access
to both drives
simultaneously
Down Down
RAID1 Creates
duplicate
drives for data
redundancy
Down Up
RAID0 Combines both
drives into one
larger drive to
improve system
performance
Up Up
17-02-025-93368C.indb 4 2/6/2017 5:02:57 PM
5
Specifications
Warranty and Product Registration
SATA Connections (2) 22-Pin SATA Data + Power
USB Connections USB 3.0 Micro-B Data (Female)
USB 2.0 Micro-B Power (Female)
Max Drive Capacity Tested up to 2 TB
Operating Temperature 50° to 122° F (10° to 50° C)
Operating Humidity 10% to 80% RH
1-Year Limited Warranty
TRIPP LITE warrants its products to be free from defects in materials and workmanship for a period
of one (1) year from the date of initial purchase. TRIPP LITE’s obligation under this warranty is limited
to repairing or replacing (at its sole option) any such defective products. To obtain service under
this warranty, you must obtain a Returned Material Authorization (RMA) number from TRIPP LITE or
an authorized TRIPP LITE service center. Products must be returned to TRIPP LITE or an authorized
TRIPP LITE service center with transportation charges prepaid and must be accompanied by a brief
description of the problem encountered and proof of date and place of purchase. This warranty does
not apply to equipment, which has been damaged by accident, negligence or misapplication or has
been altered or modified in any way.
EXCEPT AS PROVIDED HEREIN, TRIPP LITE MAKES NO WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Some states do not permit limitation or exclusion of implied warranties; therefore, the aforesaid
limitation(s) or exclusion(s) may not apply to the purchaser.
EXCEPT AS PROVIDED ABOVE, IN NO EVENT WILL TRIPP LITE BE LIABLE FOR DIRECT, INDIRECT,
SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OF THIS PRODUCT,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Specifically, TRIPP LITE is not liable for any
costs, such as lost profits or revenue, loss of equipment, loss of use of equipment, loss of software,
loss of data, costs of substitutes, claims by third parties, or otherwise.
Product Registration
Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically
entered into a drawing for a chance to win a FREE Tripp Lite product!*
* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.
17-02-025-93368C.indb 5 2/6/2017 5:02:57 PM
6
1111 W. 35th Street, Chicago, IL 60609 USA
www.tripplite.com/support
Warranty and Product Registration
WEEE Compliance Information for Tripp Lite Customers and Recyclers (European Union)
Under the Waste Electrical and Electronic Equipment (WEEE) Directive and implementing
regulations, when customers buy new electrical and electronic equipment from Tripp Lite they
are entitled to:
• Send old equipment for recycling on a one-for-one, like-for-like basis (this varies
depending on the country)
• Send the new equipment back for recycling when this ultimately becomes waste
FCC Notice, Class B
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications to this equipment not expressly approved by Tripp Lite could void the
user’s authority to operate this equipment.
Use of this equipment in life support applications where failure of this equipment can reasonably
be expected to cause the failure of the life support equipment or to significantly affect its safety or
effectiveness is not recommended.
Tripp Lite has a policy of continuous improvement. Specifications are subject to change without
notice.
17-02-025-93368C.indb 6 2/6/2017 5:02:57 PM
7
Manual del Propietario
Caja de Doble Bahía para
Unidad Portátil de Disco Duro
RAID USB 3.0 a SATA
Modelo: U357-025-2
English 1 • Français 13 • Русский 19
1111 W. 35th Street, Chicago, IL 60609 EE UU
www.tripplite.com/support
Copyright © 2017 Tripp Lite. Todos los derechos reservados.
17-02-025-93368C.indb 7 2/6/2017 5:02:57 PM
8
Contenido del Empaque
Requisitos del Sistema
Características del Producto
• U357-025-2
• Cable para Dispositivo USB 3.0 A a Micro-B, 0.61 m [2 pies]
• Cable de Alimentación USB A a Micro-B, 0.61 m [2 pies]
• Manual del Propietario
• (2) Discos duros SATA de 2.5 pulg.
(altura máxima 9.5 mm [0.4 pulg.])
• Computadora con puerto USB disponible (se rnecesita un puerto
USB 3.0 para alcanzar velocidades de USB 3.0)
• Cualquier sistema operativo equipado con USB
• Convierte dos discos SATA de 2.5 pulg. de hasta 2 TB para conexión
al puerto USB de su computadora
• Cuenta con modos de disco RAID 0, RAID 1 y JBOD para acceso
flexible a sus datos
• Diseño portátil libre de herramientas para almacenamiento externo
rápido sobre la marcha
• Soporta velocidades de transferencia de datos de hasta 5 Gbps
• Compatible con generaciones anteriores de USB
• Compatible con unidades SATA I (1.5 Gbps), SATA II (3 Gbps) y SATA
III (6 Gbps)
• Compatible con UASP para un rendimiento hasta 70% más rápido
• Conectar y Usar—No requiere software ni controladores
17-02-025-93368C.indb 8 2/6/2017 5:02:57 PM
9
Accesorios Opcionales
Instalación
• Cable de Extensión USB 3.0 SuperSpeed A a A (M/H) de la Serie U324
• Cable para Dispositivo USB 3.0 SuperSpeed (A a Micro-B M/M) de la
Serie U326
• U280-002-W12 - Cargador USB de Pared
Notas:
• Los discos HDD / SSD son sensibles a la estática y deben manejarse con
cuidado de modo que no haya riesgo de pérdida de datos Siempre maneje
una unidad HDD / SSD con cuidado usando una correa antiestática (como
P999-000 de Tripp) cuando se transporte o tocar una superficie metálica
conectada a tierra para descargar electricidad estática antes de tocar el disco.
• Si su disco SATA no ha sido formateado, debe hacerlo usando la herramienta
de Administración de Discos de su computadora a fin de copiar y acceder a
los archivos.
• Antes de desenchufar la caja, expulse correctamente el disco de su
computadora para evitar la posible pérdida de datos.
1. Asegúrese de que el botón de Bloqueo / Desbloqueo en la parte
inferior de la unidad esté colocado en Desbloqueo.
2. Deslice las cubiertas de cada lado del gabinete para mostrar la
bandeja de doble lado dpara los unidades de discos duros.
3. Deslice un disco HDD / SSD de 2.5 pulg. en cada bandeja de la
unidad.
4. Alinee la clavija SATA en los discos con los correspondientes SATA
en cada bandeja de la unidad.
5. Deslice las cubiertas a su posición original en cada lado del
gabinete.
6. Cambie el botón de Bloqueo / Desbloqueo a Bloqueo.
7. Establezca la configuración RAID. Consulte la sección y la tabla de
Modo RAID para tener instrucciones de cómo hacerlo.
17-02-025-93368C.indb 9 2/6/2017 5:02:57 PM
10
Instalación
8. Después de cambiar los switches para configuración según se
desee, mantenga oprimido el botón de restaurar hasta que los
LEDs destellen rápidamente. Si tiene éxito, el LED al lado de la
configuración elegida permanecerá encendido.
9. Encienda la unidad conectando el cable de alimentación USB
2.0 entre el puerto de entrada de CD y el puerto USB de su
computadora o un cargador USB.
10.Conecte el cable USB 3.0 incluido entre el puerto USB de la unidad
y el puerto USB de la computadora anfitrión.
11.La unidad está ahora lista para usarse.
Modo RAID
Esta unidad puede configurarse para funcionar en uno de tres modos:
JBOD, RAID1 o RAID2. A continuación se describe cada modo junto
con su correspondiente ajuste del switch de configuración.
Modo
RAID
Descripción Switch para
Configuración 1
Switch para
Configuración 2
JBOD Permite el acceso
simultáneo a ambos
discos
Abajo Abajo
RAID1 Crea discos
duplicados para
redundancia de datos
Abajo Arriba
RAID0 Combina ambos
discos en una unidad
mayor para mejorar
el rendimiento del
sistema
Arriba Arriba
17-02-025-93368C.indb 10 2/6/2017 5:02:57 PM
Tabla de contenidos
Idiomas:
Otros manuales de Recinto de Tripp Lite
Tripp Lite
Tripp Lite SmartRack SRW12US Manual de usuario
Tripp Lite
Tripp Lite SmartRack SRW9UDPVRT Manual de usuario
Tripp Lite
Tripp Lite SmartRack SR48UB Manual de usuario
Tripp Lite
Tripp Lite SR45UBDP Manual de usuario
Tripp Lite
Tripp Lite SRWOSHELFSM Manual de usuario
Tripp Lite
Tripp Lite U457-1M2-NVMEG2 Manual de usuario
Tripp Lite
Tripp Lite U357-025-SEC Manual de usuario
Tripp Lite
Tripp Lite SR42UBDPWD Manual de usuario
Tripp Lite
Tripp Lite AG-039A Manual de usuario
Tripp Lite
Tripp Lite SmartRack SRW26US Manual de usuario
Tripp Lite
Tripp Lite U258-035 Manual de usuario
Tripp Lite
Tripp Lite SRDVRLB Manual de usuario
Tripp Lite
Tripp Lite U457-025-SATAG2 Manual de usuario
Tripp Lite
Tripp Lite U256-025-R Manual de usuario
Tripp Lite
Tripp Lite SmartRack SRW18US Manual de usuario
Tripp Lite
Tripp Lite SmartRack SR42UBZ4 Manual de usuario
Tripp Lite
Tripp Lite SREXTENDER Manual de usuario
Tripp Lite
Tripp Lite SmartRack SR42UBEIS Manual de usuario
Tripp Lite
Tripp Lite SRIN418186 Manual de usuario
Tripp Lite
Tripp Lite SmartRack NEMA 12 Manual de usuario
