Triple S 20C Manual de usuario

READ THIS BOOK

OPERATING & MAINTENANCE

INTRODUCTION INSTRUCTIONS

AUTOMATIC SCRUBBER

MODEL 20C

This operator’s book has important information for the use

and safe operation of this machine. Read this book care-

fully before starting the machine. Keep this book and tell

all operators to read the book. If you do not follow the

instructions, you can cause an injury or damage equipment,

furniture or buildings.

For additional information refer to the Triple S website

www.triple-s.com or write to:

Triple S

2 Executive Park Drive

Billerica, MA 01862

Carefully inspect all components to ensure that there is no

concealed freight damage. If such damage is discovered,

ﬁle a “CONCEALED DAMAGE REPORT” immediately

with the delivering carrier.

The contents of this manual are based on the latest product

information available at the time of publication. Triple S

reserves the right to make changes or improvements to its

machines without notice.

FOR YOUR CONVENIENCE, RECORD THIS

IMPORTANT INFORMATION:

MODEL_______________________________

SERIAL NUMBER______________________

PART NUMBER ________________________

DATE PURCHASED ____________________

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS

SYMBOLS USED ON THE MACHINE

MACHINE PREPARATION

1. UNPACKING THE MACHINE

2. BATTERY INSTALLATION

3. CONNECTING THE BATTERY CHARGER

4. CHARGING THE BATTERIES

5. CONNECTING THE BATTERY CONNECTOR

6. BATTERY CHARGE LEVEL INDICATOR

7. SQUEEGEE ASSEMBLY

8. ADJUSTING THE SQUEEGEE HEIGHT

9. ADJUSTING THE SQUEEGEE INCLINATION

10. INSTALLING THE SPLASH GUARD

11. BRUSH INSTALLATION

12. RECOVERY TANK

13. SOLUTION WATER

OPERATION

OPERATING

DEVICE TOO FULL

MOVEMENT

UPON COMPLETION OF THE WORK

DAILY MAINTENANCE

CLEANING THE RECOVERY TANK

CLEANING THE VACUUM FILTER

CLEANING THE SQUEEGEE

REPLACING THE SQUEEGEE BLADES

DISASSEMBLY OF THE BRUSH

WEEKLY MAINTENANCE

CLEANING THE SQUEEGEE HOSE

SOLUTION TANK CLEANING

TROUBLE SHOOTING GUIDE

INSUFFICIENT WATER ONTO THE BRUSH

THE MACHINE DOES NOT CLEAN SATISFACTORILY

THE SQUEEGEE DOES NOT DRY THE FLOOR WELL

EXCESSIVE FOAM PRODUCTION

WARRANTY POLICY

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

○○○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○

READ AND UNDERSTAND ALL INSTRUCTIONS AND WARNINGS BEFORE OPERATING

THIS MACHINE!

WARNING: To reduce the risk of fire, electric shock or injury:

1. You must have training in the operation of the machine before using it. READ THE

INSTRUCTION BOOK. If you do not understand any instruction, ask your supervisor.

2. Make sure all labels, decals, warnings, cautions and instructions are fastened to the machine.

3. Read the labels carefully on the machine. Do not cover them for any reason and replace them

if damaged.

4. Do not operate this machine unless it is completely assembled, inspect the machine carefully

before operation.

5. Pay close attention to other people and especially children while operating this machine.

6. Be a careful driver, do not strike shelving or scaffolding, especially where there is a danger of

falling objects.

7. Machines can cause an explosion when operated near flammable materials and vapors. Do

not use this machine with or near fuels, grain dust, solvents, thinners, or other flammable

materials.

8. In case of fire, use a powder extinguisher. Do not use water.

9. Do not use this machine as a means of transport.

10. Do not use acid solutions that could damage the machine.

11. Adjust your speed to the conditions of the floor.

12. Do not turn the machine on a ramp. Do not stop and leave the machine on a ramp or incline.

13. When the machine is parked, take out the key and set the parking brake.

14. During any maintenance operation disconnect the power supply from the machine.

15. Lead acid batteries generate gases that can cause an explosion. Read the instruction manual

supplied with the battery charger. Keep sparks and flames away from batteries.

NO SMOKING. Charge the batteries only in an area with good ventilation.

16. Do not use a charger if the power cord is damaged.

17. Always wear eye protection and protective clothing when working near batteries. Remove all

jewelry. Do not put tools or other metal across the battery terminals, or the tops of the batter-

ies.

18. Check the level of the electrolyte every time you charge the batteries. If the level is low, add

distilled water only.

19. Maintenance and repairs must be performed by authorized Service Centers only. Make ad-

justments according to the specifications given in the service manual for this machine.

20. Keep the electrical parts of the machine dry. Do not wash the machine with direct water jets or

high pressure, nor with corrosive material. For storage, keep the machine in a dry building.

21. Water solutions or cleaning materials used with this type of machine can leave wet areas on

the floor surface. These areas can cause a dangerous condition for the operator or other per-

sons. Always put CAUTION signs near the area you are cleaning.

22. Do not reach under shrouds with fingers, hands, or toes when machine is running.

IMPORTANT SAFETY INSTRUCTIONS

SYMBOLS USED ON THE MACHINE

Symbolforthewaterlever:

Indicatesthevalve isopen.

Symbol for the brush:

Indicates the brush motor switch.

Symbol for the vacuum motor:

Indicates the vacuum motor switch.

Symbol indicating the raised or lowered position of the squeegee:

Indicates the squeegee lever position.

Symbol indicating the charge levels of the batteries:

It is necessary to recharge the batteries when the green light begins to blink

Indicatesthedrainhoseoftherecovery tank.

Indicationofthemaximumrecommended temperatureforthe solutionwater(50°C or

122°F): It is located near the fill hole of the solution tank.

Symbolforthecoupling:

Indicates the anchor points and the load direction.

Symbolindicating theraisedorlowered positionofthebrushbase:

Indicatesthe lever forliftingthe brushbase.

MACHINE PREPARATION

1. UNPACKING THE MACHINE

1. Use a fork truck to move the machine when packaged.

2. Take off the outer package

3. The machine is fixed on the pallet with wooden wedges that block the wheels.

4. Take the wedges off.

5. Using a ramp, pull the machine down from the pallet, pushing it in reverse

motion. Avoid violent blows to the base.

2. BATTERY INSTALLATION

The two 12 volt batteries fit in the compartment under the recovery tank.

For battery maintenance and charging, follow the instructions

provided by the battery supplier.

InstallationInstructions:

1. Lift the recovery tank forward.

2. Detach the squeegee hose (1) from the recovery tank.

3. Take off the vacuum plug (2) by rotating it counterclockwise.

4. Remove the drain hose from its’ hook and take the recovery tank off.

MACHINE PREPARATION

5. Place the batteries in their compartment.

6. Connect the batteries’ connector (2) to the machine’s connector (1).

7. Reassemble the recovery tank, vacuum plug and squeegee hose.

3. CONNECTING THE BATTERY CHARGER

The battery chargers’ connector fits into the battery connector (2) located under the

recovery tank.

4.CHARGINGTHEBATTERIES

Make sure the battery charger is for use with the installed battery, both capacity and

type(lead/acidorGEL). WARNING! NEVERCHARGEAGELBATTERYWITH

ANINCORRECTBATTERYCHARGER.

NEVERALLOWTHEBATTERIESTORUNCOMPLETELYDOWN,rechargethem

withina few minutes after the battery indicator starts blinking.Never leave thebatteries

completelydischarged, even if the machine is not being used.

When charging the batteries, keep the recovery tank lifted with the prop as shown in

the figure.

Turn the key to the OFF position. Connect the DC connector on the charger to the

DC battery connector. Connect the AC charger plug to a receptacle that has the

correct voltage and frequency for your charger. Make sure the receptacle is

connected to the electrical ground.

WARNING! When charging the batteries, follow all the instructions

provided with this manual and the battery charger. Trained staff must carry

out the installation and maintenance operations.

WARNING!FireDanger:Lead acid batteries generate gases that can cause

anexplosion. Keepsparks and flames away from batteries. NOSMOKING!

WARNING! To prevent an explosion, charge the batteries only in an area

with good ventilation.

WARNING! Always wear eye protection and protective clothing when

working near batteries.

MACHINE PREPARATION

5. CONNECTING THE BATTERY CONNECTOR

After charging the batteries, reconnect the battery connector (2) to the connector of

the machine (1).

6.BATTERYCHARGELEVELINDICATOR

The batteries’ indicator is digital with 4 fixed positions and a blinking one. The

numbers, which appear on the display, show the approximate charge level.

4= maximum charge, 3= charge 3/4, 2= charge 2/4, 1= charge 1/4,

0= (blinking) discharged batteries)

7. SQUEEGEE ASSEMBLY

The squeegee is assembled as shown in the figure. The squeegee lever should be in

its up position. Insert the holding pin into the squeegee stud bolt to secure the

squeegee in place. Then fit the squeegee hose into its coupling; the hose should be

located to the right of the lifting cable.

8.ADJUSTINGTHESQUEEGEEHEIGHT

The height from the floor to the squeegee should be adjusted based on the blade’s wear.

Rotate the wing nuts (1) counter-clockwise to lift the squeegee and clockwise to lower

it.

Note: Adjust the right and left wing nuts the same amount; the squeegee should be

positioned parallel to the floor.

NOTE: The brush motor automatically switches off a few seconds after the battery

indicator light begins to blink. By restarting the machine, you will be allowed to turn

on the vacuum motor and finish drying any wet areas.

5mm

MACHINE PREPARATION

9. ADJUSTING THE SQUEEGEE INCLINATION

During operation, the rear squeegee blade is most efficient when tilted back about

3/16 inch (5mm) along its whole length. To increase the blade bending in the central

part, tilt the squeegee body backward by turning the adjuster counter-clockwise.

Subsequently, turn the adjuster clockwise to increase the bending at the sides of the

squeegee blade.

10. INSTALLINGTHESPLASHGUARD

The splash guard should be installed as shown in the picture.

11. BRUSHINSTALLATION

1. Lift the brush base with the foot pedal.

2. Place the brushes under the base. Line up the lugs with the holes in the brush plate.

Insert the brushes into the plate and turn each brush so the lugs are pushed toward

their retaining springs, until locked in place.

The picture shows the direction of rotation for the right brush. The left brush is

rotated in the opposite direction.

MACHINE PREPARATION

12.RECOVERYTANK

Open the lid and confirm the following connections are secure:

1. The vacuum plug (2) is securely attached, turn clockwise to tighten.

2. The vacuum hose (1) is attached.

3. The plug on the drain hose (on the back of the machine) is inserted.

13. SOLUTIONWATER

Fill the solution tank with clean water at a temperature not more than 50°C/122°F. Add

the proper concentration of liquid detergent by following the manufacturer instructions.

Excess foam in the recovery tank can damage the vacuum motor, so use only the mini-

mum amount of detergent necessary. Reassemble the cover.

WARNING!: Always use low foaming detergent. Adding antifoam liquid into

the recovery tank before cleaning will also help prevent foaming. NEVER USE

PUREACID.

3. Invert the positions of the right and left brushes daily. However, if the brushes are

not new and have deformed bristles, it is better to reassemble them in the same position.

Because the different inclination of the bristles may cause an overload to the brush

motor and excessive vibrations.

Tabla de contenidos

Otros manuales de Máquina de piso de Triple S

Triple S

Triple S Ace 20T Manual de usuario

Triple S

Triple S Q-LINE Series Manual de instalación y operación

Triple S

Triple S Cheetan 1500 Manual de usuario

Triple S

Triple S Cougar 17 Manual de usuario

Triple S

Triple S Ace 26T1 Manual de usuario

Triple S

Triple S panther 26T Manual de usuario

Triple S

Triple S 20B Manual de usuario

Triple S

Triple S Q-1500 Manual

Triple S

Triple S MS-31 Manual de instalación y operación

Triple S

Triple S JAGUAR 20R Manual de usuario

Triple S

Triple S 20D Manual de instalación y operación

Triple S

Triple S TR Series Manual de instalación y operación

Triple S

Triple S POWER SPOTTER 4 Manual de instalación y operación

Triple S

Triple S ACHIEVER 40 Manual de instalación y operación

Triple S

Triple S Ace 26BA1 Manual de usuario

Triple S

Triple S Q-17 Manual de instalación y operación

Triple S

Triple S PANTHER 15B Manual de usuario

Triple S

Triple S Wildcat Manual de usuario

Triple S

Triple S 17 XL Manual de instalación y operación

Manuales populares de Máquina de piso de otras marcas

Nilfisk-Advance

Nilfisk-Advance Advance SC370 17B Manual de usuario

Numatic

Numatic ET 4045 Manual de usuario

HAWK ENTERPRISES

HAWK ENTERPRISES HP1513-180BRUTE Manual de usuario

Mytee

Mytee 8070 Mytee-Lite Manual de usuario

Kärcher

Kärcher B 140 R Manual de usuario

Nilfisk-Advance

Nilfisk-Advance SW 750 Manual de usuario

Tornado

Tornado Marathon 2000 98190 Manual

Windsor

Windsor ADMIRAL Admiral 8 Manual de usuario

Numatic

Numatic TTB 1117/100 Manual de usuario

Tennant

Tennant 8210D Manual de usuario

Nobles

Nobles Frontier Manual del producto

lavina

lavina 21-X Manual de usuario

KENT

KENT Edge 28B Manual de usuario

Tennant

Tennant 215 Manual del producto

Windsor

Windsor BDP 51/2000C Manual de usuario

CleanFreak

CleanFreak DURA-18HD Manual de usuario

Nilfisk-Advance

Nilfisk-Advance Warrior 34RST Guía del administrador

BETCO

BETCO PB24 Manual de usuario