Tribe FLATCOB40 Manual de usuario
USER MANUAL
MANUALE UTENTE
FLATCOB40
FLATCOB80
EN - IT
COMPACT LED PROJECTOR
All rights reserved by Music & Lights S.r.l. No part of this instruction manual may be
reproduced in any form or by any means for any commercial use.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the
characteristics stated in this instruction manual at any time and without prior notice.
All revisions and updates are available in the ‘manuals’section on site www.musiclights.it
REV.003-05/17
1
FLATCOB40/80
Packing content • FLATCOB40/80
• Mount bracket (2pc.)
• Power cable
• User manual
TABLE OF CONTENTS Safety
General instructions
Warnings and installation precautions
1 Introduction
1. 1 Description
1. 2 Technical specications
1. 3 Operating elements and connections
2 Installation
2. 1 Mounting
3 Functions and settings
3. 1 Operation
3. 2 Basic
3. 3 Menu structure
3. 4 Auto show
3. 5 Static Color
3. 6 Sound Mode
3. 7 Manual Color
3. 8 Dimmer
3. 9 Unit temperature
3. 10 Linking
3. 11 DMX conguration
3. 12 DMX addressing
3. 13 Connection of the DMX line
3. 14 Construction of the DMX termination
3. 15 DMX control
3. 16 Operation through the IRC controller
4 Maintenance
4. 1 Maintenance and cleaning the unit
4. 2 Fuse replacement
4. 3 Troubleshooting
2
2
3
3
5
6
7
7
8
8
8
9
9
9
9
9
10
10
11
11
12
13
14
14
14
FLATCOB40/80
2
WARNING! Before carrying out any operations with the unit, carefully read this instruction
manual and keep it with cure for future reference. It contains important information about
the installation, usage and maintenance of the unit.
SAFETY
General instruction
• The products referred to in this manual conform to the European Community Directives and are there-
fore marked with .
• The unit is supplied with hazardous network voltage (230V~). Leave servicing to skilled personnel only.
Never make any modications on the unit not described in this instruction manual, otherwise you will
risk an electric shock.
• Connection must be made to a power supply system tted with ecient earthing (Class I appliance ac-
cording to standard EN 60598-1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately sized residual current devices.
• The connection to the main network of electric distribution must be carried out by a qualied electrical
installer. Check that the main frequency and voltage correspond to those for which the unit is designed
as given on the electrical data label.
• This unit is not for home use, only professional applications.
• Never use the xture under the following conditions:
- in places subject to vibrations or bumps;
- in places with a temperature of over 45 °C.
• Make certain that no inammable liquids, water or metal objects enter the xture.
• Do not dismantle or modify the xture.
• All work must always be carried out by qualied technical personnel. Contact the nearest sales point for
an inspection or contact the manufacturer directly.
• If the unit is to be put out of operation denitively, take it to a local recycling
plant for a disposal which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way dierent to the one described in this manual, it may suer
damage and the guarantee becomes void. Furthermore, any other operation may lead to dangers like
short circuit, burns, electric shock, etc.
• Before starting any maintenance work or cleaning the projector, cut o power from the main supply.
• Always additionally secure the projector with the safety rope.When carrying out any work, always com-
ply scrupulously with all the regulations (particularly regarding safety) currently in force in the country
in which the xture’s being used.
• Install the xture in a well ventilated place.
• Keep any inammable material at a safe distance from the xture.
• Shields, lenses or ultraviolet screens shall be changed if they have become damaged to such an extent
that their eectiveness is impaired.
• The lamp (LED) shall be changed if it has become damaged or thermally deformed.
• Never look directly at the light beam. Please note that fast changes in lighting, e. g. ashing light, may
trigger epileptic seizures in photosensitive persons or persons with epilepsy.
• Do not touch the product’s housing when operating because it may be very hot.
3
FLATCOB40/80
- 1 - INTRODUCTION
1.1 DESCRIPTION
FLATCOB40/80 is a compact LED projector equipped with a COB source that allows to place a bright RGB/
FullColor 40/80W LED in a superslim housing. The light source features 60° beam angle, with a magnetic
lens holder (included) to switch the projection at 30°. FLATCOB40/80 can be controlled wireless through
the optional USB Wi-Fi receiver in combination with Wibox and the smartphone App SmartColor, or
through IR remote. FLATCOB40/80 has also been designed with signal and power connections on the
sides and a at bottom, resulting very useful for oor applications as compact and powerful wall-washer.
Its round shape and die-cast aluminum housing with tempered glass panel make FLATCOB40/80 a nice
design tool which can be used also for insight applications in every kind of events as conference, wedding
parties, fashion events, exhibitions.
1.2 TECHNICAL SPECIFICATIONS
LIGHT SOURCE
• Source: 1x40W RGB LED
• Luminous ux: 705.32lm
• Lux: (60°) 54,1 - (30°) 380,9 lux @3mlux @3m full
• Source life expectancy: >50.000 h
OPTICS
• Beam angle: 18-45°
• Field angle: 28-93°
• Lens type: reector with collimator to achieve asymmetric beam diusion
• Additional optics: 30° (inc)
COLOUR SYSTEM
• Colour mixing: RGB/FC
• Colour wheel: virtual colour wheel with presets
DYNAMIC EFFECTS
• Static colour mode: selection of static colour
• Manual colour mode: manual adjustment of colour
• Auto mode: built-in programs with execution speed adjustment
• Sound mode: music activation through internal microphone and sensitivity control
BODY
• Body: sturdy die-cast aluminium body conceived for long-time durability
• Body colour: black
CONTROL
• Protocols: DMX512
• DMX channels: 3/8channel
• Display: LED display user interface
• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included
• IR: infrared sensor controlled by remote
• Master/Slave: for synchronized operation of more units linked in a chain
FLATCOB40/80
4
ELECTRONICS
• Dimmer: linear 0~100% electronic dimmer
• Dimmer curves: 4 dierent dimming curves available
• Strobe / shutter: 1-28 Hz, electronic
• Operating temperature: -10° ~ +45°
• Flicker: icker free operation
ELECTRICAL
• Power supply: 100-240V – 50/60Hz
• Power consumption (at 230V): 34W
• Power consumption (at 120V): 34.3W
• Output (at 230V): 36 units on a single power line
• Output (at 120V): 19 units on a single power line
PHYSICAL
• Cooling: natural cooling of the peculiar chassis and to absence of fans
• Sospension and xing: double hanging bracket suitable for safe hanging and for oor positioning
• Data: USB port for USB WIFI transmitter (optional)
• Signal connection: XLR 3p IN/OUT connectors
• Power connection: IEC IN/OUT connectors
• IP rating: 20
• Dimensions (WxHxD): 189x151x220mm
• Weight: 1.5kg
FLATCOB40
LIGHT SOURCE
• Source: 1x80W RGB LED
• Luminous ux: 1511lm
• Lux: (60°) 171 lux - (30°) 923lux @3m full
• Source life expectancy: >50.000 h
OPTICS
• Beam angle: 18-52°
• Field angle: 31-96°
• Lens type: reector with collimator to achieve asymmetric beam diusion
• Additional optics: 30° (inc)
COLOUR SYSTEM
• Colour mixing: RGB/FC
• White presets: 3200~10000K
• Colour wheel: virtual colour wheel with presets
• Macros: built-in white presets
DYNAMIC EFFECTS
• Static colour mode: selection of static colour
• Manual colour mode: manual adjustment of colour
• Auto mode: built-in programs with execution speed adjustment
• Sound mode: music activation through internal microphone and sensitivity control
5
FLATCOB40/80
Technical drawing
FLATCOB40 FLATCOB80
Fig.1
151
189 220
162
200 230
BODY
• Body: sturdy die-cast aluminium body conceived for long-time durability
• Body colour: black
CONTROL
• Protocols: DMX512
• DMX channels: 3/8channel
• Display: LED display user interface
• Firmware upgrade: yes, via USB-DMX interface (UPBOX1) not included
• IR: infrared sensor controlled by remote
• Master/Slave: for synchronized operation of more units linked in a chain
ELECTRONICS
• Dimmer: linear 0~100% electronic dimmer
• Dimmer curves: 4 dierent dimming curves available
• Strobe / shutter: 1-28 Hz, electronic
• Operating temperature: -10° ~ +45°
• Flicker: icker free operation
ELECTRICAL
• Power supply: 100-240V – 50/60Hz
• Power consumption (at 230V): 56W
• Power consumption (at 120V): 55.6W
• Output (at 230V): 23 units on a single power line
• Output (at 120V): 12 units on a single power line
PHYSICAL
• Cooling: natural cooling of the peculiar chassis and to absence of fans
• Sospension and xing: double hanging bracket suitable for safe hanging and for oor positioning
• Data: USB port for USB WIFI transmitter (optional)
• Signal connection: XLR 3p IN/OUT connectors
• Power connection: IEC IN/OUT connectors
• IP rating: 20
• Dimensions (WxHxD): 200x162x230mm
• Weight: 2kg
FLATCOB40/80
6
1.3 OPERATING ELEMENTS AND CONNECTIONS
1. MOUNTING BRACKET
2. LOCKING KNOB for the mounting bracket
3. CONTROL PANEL with display and 4 button
used to access the control panel functions and
manage them.
4. MICROPHONE to control the show by the ex-
ternal audio signal.
5. SAFETY EYE to attach safety cable
6. POWER OUT: connect to supply power to the
next unit.
7. POWER IN mains plug for connection to a socket
(100-240V~/50-60Hz) via the supplied mains
cable. The support for the mains fuse is located
near the mains plug. Only replace a blown fuse
by one of the same type.
8. Universal Serial Bus (USB)
9. DMX IN (3-pole XLR):
10.1 = ground, 2 = DMX -, 3 = DMX +
11.DMX OUT (3-pole XLR):
12.1= ground, 2 = DMX -, 3 = DMX +
Fig.2 - Rear panel
1
2
3 4
5
67
10 9
8
7
FLATCOB40/80
- 2 - INSTALLATION
2.1 MOUNTING
FLATCOB40/80 may be set up on a solid and even surface. The unit can also be mounted upside down to a
cross arm. For xing, stable mounting clips are required. The mounting place must be of sucient stability
and be able to support a weight of 10 times of the unit’s weight.
When carrying out any installation, always comply scrupulously with all the regulations (particularly re-
garding safety) currently in force in the country in which the xture’s being used.
Install the projector at a suitable location by means of the mounting bracket (1).
Always additionally secure the projector with the safety rope from falling down. For this purpose, fasten
the safety rope at a suitable position so that the maximum fall of the projector will be 20 cm.
Adjust the projector and use the knob (2) to slightly release or tighten the locking mechanism of the
bracket if is necessary.
Fig.3
2
1
FLATCOB40/80
8
Fig.4 - Functions of the buttons
MENU UP DOWN ENTER
- 3 - FUNCTIONS AND SETTINGS
3.1 OPERATION
Connect the supplied main cable to a socket (100-240 VAC-50/60 Hz). Then the unit is ready for operation
and can be operated via a DMX controller or it independently performs its show program in succession.
To switch o, disconnect the mains plug from the socket. For a more convenient operation it is recom-
mended to connect the unit to a socket which can be switched on and o via a light switch.
3.2 BASIC
Access control panel functions using the four panel buttons located directly underneath the LED Display
(g.4).
MENU UP DOWN ENTER
Used to access the menu or
to return a previous menu
option
Navigates downwards through
the menu list and increases
the numeric value when in a
function
Navigates upwards through
the menu list and decreases
the numeric value when in a
function
Used to select and store the
current menu or conrm the
current function value or
option within a menu
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
Idiomas:
Otros manuales de Proyector de Tribe
