TRIATEK BASnet LightiView Manual de usuario

1025 Cobb Place Blvd Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.triateklighting.com

BASnet LightiView™ User’s Guide

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 2 of 4105/26/2005

This section serves as a notice of the immediate or potential dangers involved when

working with the equipment described throughout this manual. Any person involved

in installation, maintenance, or service of the equipment should first carefully

examine the equipment and read the instructions contained in this manual to ensure

that personal and/or equipment injury is avoided.

The following safety messages are used throughout this manual to alert of

immediate or potential danger to life or property:

In addition, this symbol may appear in the margin of specific portions of text as a

safety reminder. Applicable instruction steps will be listed beneath the symbol.

Instructions contained in this user’s guide should be performed only by qualified

persons in accordance with local and national codes. TRIATEK®Lighting, Inc. and

its affiliates assume no responsibility for any consequences related to the improper

use of this manual.

CAUTION: Used without the safety alert symbol, indicates a potentially

hazardous situation which, if not avoided, can result in personal or

property damage. Failure to comply with proper handling of the TRIATEK

Lighting products may void your warranty

ATTENTION

DANGER! Indicates an immediately hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING! Indicates a potentially hazardous situation

which, if not avoided, can result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not

avoided, can result in minor or moderate injury.

Disclaimer

Hint Indicates a tip or trick to help you with setting up or

controlling the BASnet LightView.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 3 of 4105/26/2005

What’s New in LightView 3.0* ?

(*Present version is called 2.0 in BLV Users Guide.)

New Features

• Dial up modem can be connected to 232 port to serve up the BLV web pages. A selector switch is provided use the

232 port as a console or modem connection.

• Firmware upgrade flash capability. Users can receive a firmware image from TRIATEK Lighting and upload it via the

web interface.

• Import groups from LPPK. Previously, users must set up the panel groups in again in BLV even if they already existed

in the LPPK file. Now the user creates the panel groups just once in LPPK and simply imports them to BLV.

• Multi-event linking for photocells. Previously, multi-lamp lighting events for photocells were not truly linked resulting

conflicting commands sent over the network. Now photocell events can linked in setup to work together. The protocol

establishes the correct command for linked multi-lamp levels used in day lighting.

• Event log e-mail option. Users can specify sender address, destination address, and time when event logs are to be

automatically emailed. An energy manager could thus arrange for event logs from multi-sites to be sent to his office.

• Motion sensor group can be used to qualify photocell event. Previously, this could only be effectively done in

conjunction with hard wire methods to the LMB.

• Lighting groups are now sorted. Previously, the groups were placed at the top of the BLV group list page. This was

cumbersome when groups were inserted later and appeared out of numerical order. Now a new entry is inserted in its

proper order, according to panel and group number even if added later.

• TI-45-Net global commands. Previously, users needed to call in a separate user ID for each panel. Now a special

block of reserved user ID codes can be mapped to multiple panels allowing 1 call to control a BLV Area spanning

several panels.

Improvements

• Enhanced logging capability. Events log increased from 30 to 100. Command log increased from 100 to 500.

• Areas increased from 100 to 250.

• Qualifiers increased from 30 to 100.

• Area names appear at top of group-assignment-to-area page. Previously, the page did not identify which area the

groups were being assigned to.

• Ignore TI-Net override if overtaken by BLV schedule. Previously, if a TI override On was followed by BLV scheduled

ON, the TI would turn Off the circuit during the middle of the scheduled period. Now the TI Off is ignored when

superceded by a BLV schedule.

• BLV no longer automatically times out after 6 minutes of inactivity. The timeout is user adjustable.

• Data base converter. A separate program is available to convert databases made in rev’s 1.0, 2.0, 2.0a, 2.1, and

2.1.1(=3.0).

Hint:

Use the Table of Contents. It is

provided as a map to guide you

through the essential items needed

for your particular application of

LightView.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 4 of 4105/26/2005

What’s Was New in LightView 2.0 ?

• Daylight Savings Time - Pg 38 - When enabled by the user, this feature will automatically change BLV’s clock to Daylight

Savings Time when DST is in effect.

• Six Astronomical Events - Pg 25 - Astronomical Events allow lighting events to be scheduled based on sunrise and

sunset times forecast by LightView. This feature is ideal for scheduling outdoor lighting or appropriate indoor areas that

depend on sunlight illumination.

• Thirty Photocell Events - Pg 24 - Photocell events are used to control lights based on variable sunlight illumination

levels. Up to 30 photocells can be placed at different areas so that lighting can be controlled for daylight harvesting or

outdoor scheduling. BLV also allows specifi cation of a dead band tolerance to prevent spurious triggering of lights.

• Thirty Continuous Qualifi ers - Pg 22 - Earlier versions of LightView only qualifi ed an event once. This new feature

continuously monitors a user-specified group and detects state changes. A state change then triggers user-defi ned

actions on a list of areas. This feature is ideal for installations that require a switched input on one panel to control other

panels.

• Automatic IP Address Discovery - Pg 7- This feature is ideal for users that connect directly to an BLV module using

crossover cables. This allows users to communicate with BLV without reconfi guring their network settings. The process

is initiated by pressing a switch on BLV and then accessing any address within the computer’s subnet from Internet

Explorer. BLV will detect the address requested by Internet Explorer and reconfi gure itself to that address.

• Name up to 1000 Groups - Pg 14 - Earlier versions of LightView control up to 1000 Groups but support assigning a

23-character description to only 254 of the 1000 Groups. The ability to assign 23- character descriptions to up to 1000

Groups is useful for installations that use the “Area and Group Status” feature to override or monitor Group status of an

entire lighting network.

• LPPK with LightView - Pg 47 - LightView 2.0 now interfaces with LPPK to allow users to program all TRIATEK Lighting

panels connected to LightView over the Internet from any remote location.

• Telephone Interface with LightView - Pg 44 - LightView is configured to work with TI-4500-0-Net, TRIATEK’s telephone

override interface. Ti- 4500-0-net with LightView provides up to 8191 password–protected user ID’s and up to 6 hours

of override plus cancellation of on-going override. Voice prompts can be customized by the user.

• Documentation - LightView documentation is presented in two publications: LightView User’s Guide and LightView

Installers Guide. For basic physical installation and wiring, refer to LightView Installer’s Guide. For all other matters, refer

to this publication.

To use LightView successfully, three things must be accomplished:

1) LightView must be installed properly.

2) LightView must be set-up to communicate with a Laptop or PC.

3) Once communication is established, LightView must be programmed to control the lighting panels. Once these three

items are done, LightView can operate either “stand-alone” or remain connected to the workstation or LAN.

To Install LightView:

• Refer to publication, LightView Installation Guide.

To Set-Up LightView:

• Set an IP address in LightView compatible with the subnet of the workstation or LAN.

• Details are covered in this document’s main sections:

Setting Up BLV and Connecting to BLV.

To Program LightView:

• Define the Lighting Panel Groups

• Define the Lighting Areas

• Assign the Panel Groups to the Areas

• Schedule the Areas.

• Details are covered in this document’s main section: Programming BLV.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 5 of 4105/26/2005

Contents

BASnet LightView User’s Guide

What’s Was New in LightView 2.0 ?. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

What’s New in LightView 3.0* ? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

BASnet LightView Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

BASnet LightView Ports and LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Setting Up BASnet LightView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Automatic IP Address Discovery. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Conﬁguring BLV Using a Serial Connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setting Up Hyperterminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Setting Up Network Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Setting the Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to the BASnet LightView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Checking the version of Internet Explorer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Logging In. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Navigating the BASnet LightView. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Programming the BASnet LightView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Deﬁning Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Creating Areas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Creating Schedules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Event Details . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setting the Duration of the Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using Multiple Day Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Using Single Day Scheduling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Setting the Date Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Naming the Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Event Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Qualifying a Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Photocells . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Astronomical Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Lighting Area Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Adding New Areas to the Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Viewing the Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Monitoring and Overriding Areas and Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Viewing Cause Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Viewing Graphics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Creating Holidays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Viewing System Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Setting Coordinates and the Internal Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Setting IP Conﬁguration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Uploading Graphics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Backup and Restoration of Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Backing Up Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Restoring Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Deleting the System Database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Telephone Override with BASnet LightView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Assigning Codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Range of ID Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Steps to Setup TI-4500-NET . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

LPPK with BASnet LightView . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

BASnet LightView Programming Worksheets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Area and Group Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Holidays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Schedules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Latitued and Longitude Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 6 of 4105/26/2005

BASnet LightView Overview

The BASnet® LightView™ (BLV) is a Web-based programming system that enables lighting control from an internet

browser. The browser functions to execute scheduled event commands upon pre-defined lighting areas. These areas

can be planned and designed with the use of worksheets, and they then can be entered into the module via BLV system.

BLV’s functionality is based on

a structure that utilizes lighting

panels, groups and areas. This

structure provides a logical

and organized system. Their

relationship is defined briefly

as follows: Lighting areas are

composed of one or more lighting

groups, and lighting groups are

composed of one or more relays in

a lighting panel. Each lighting panel

employed by BLV has its own

groups assigned to it. A lighting

group never spans multiple lighting

panels. The browser can handle

schedules for up to (inclusive) 100

lighting areas, and 1000 lighting

groups. The system allows the

user to input, change and view all

information related to the lighting

areas.

A summary of the systems components and associated functionality follows:

1.) The Main Menu of links to all pages in the system.

2.) Lighting Groups Assignment where groups are assigned to panels.

3.) Lighting Area Assignment where areas are created and groups are assigned to areas.

4.) Scheduling Events where areas are given actions to perform and grouped by time the actions occur.

5.) Viewing Events of all schedules in the system.

6.) “Today’s” Event List displays the events scheduled to occur that day.

7.) Holiday List page provides addition and modification of holidays into the system.

8.) Area and Group Status displays the current ON/OFF states of the areas and groups, allows manual override of the areas

and groups, and uploaded maps can be viewed.

9.) System Setup includes system clock alteration, Network address configuration, upload maps, backup and restoration of

system database, and deletion of database.

10.) System Logs records any phenomena related to a schedule and an area including creation, modification, and qualification

of schedules and success or failure of action on areas, along with the time stamp of these phenomena.

11.) BASnet LightView is able to receive telephone override commands from TRIATEK’s TI-4500-NET telephone interface

module. See pages 31-33 for details.

12.) BASnet LightView interfaces with LPPK to allow users to program lighting panels connected to BASnet LightView over

the Internet from any remote location.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 7 of 4105/26/2005

Optional

Power Jack

24vdc

Reset

Auto IP Discovery Power

24vdc

DB9-M

RS-232

Serial Port

RJ-45

Ethernet

Port

COM1

RS-485

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 8 of 4105/26/2005

Setting Up BASnet LightView

Automatic IP Address Discovery This feature is ideal for users that connect directly to BLV modules using crossover

cables. This allows users to communicate with BLV without reconfiguring the network settings on their laptop or

PC. LightView will configure its IP address to be compatible with the user’s laptop. Use this feature only with direct

connections to BLV.

To use Automatic IP Address Discovery:

• Determine the network IP address of the laptop or PC. Typically, right click “My Network Places” then select Properties.

• Next, select TCP/IP for the ethernet card and then click on the Properties button.

• Connect Laptop or PC to BLV using ethernet cross-over (“null modem”) CAT5 cable.

• Open Internet Explorer

• Depress the auto discovery Switch in BLV. See diagram below.

• On the address bar at the top of the Internet Explorer page, enter an IP address within the range of the laptop’s subnet.

• LightView will reconfigure itself to an IP compatible with the laptop’s address.

Configuring BLV Using Serial Console

When Auto IP Discovery cannot be used, set the IP via BLV’s serial console and HyperTerminal. The RS-232 serial

programming cable is used to set initial low-level system settings such as network addresses and the browser password

with a serial console program. It is not necessary to use the serial interface for any future changes of the network

addresses because the LightView Browser can be used for this purpose. (See “Setting IP Configuration” on page 28).

The browser password, however, can only be changed through the serial console interface. HyperTerminal, which comes

standard with most if not all current versions of Microsoft®Windows®is a serial console program that can be used to

change the low-level settings.

Setting Up HyperTerminal

In order to communicate to the BLV module, the IP, gateway, subnet mask

and name server addresses need to be changed. To change each of

these settings, firstly, run a terminal program. The example to the left uses

HyperTerminal. HyperTerminal can normally be found in Windows Accessories

under Communications.

The first window that displays in HyperTerminal is the Connection Description

window shown to the left. Name the connection, select an icon, and click

“OK”. In the next window shown below, select the Communications port the

RS-232 cable is connected to on the host computer, and click “OK”.

Reset

Auto IP Discovery

Hint:

Push pin through this hole

to activate internal switch for

automatic IP discovery. Use this

feature only with direct connections

to BLV.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 9 of 4105/26/2005

Setting Up BASnet LightView

Setting Up HyperTerminal (continued)

Next, specify communications port information used with the communications port is

entered in the “... Properties” window. Select the same values used below and click

“OK”. These values are required for proper communication with the BLV module. For

information concerning the meaning of each field refer to HyperTerminal documentation.

If using another terminal program, the format of the fields into which the data is entered

will be different, but the same information will need to be supplied.

Setting Network Address

After providing the proper communications port settings, the terminal window will open. The “set” command is used to

input the network settings which have associated variables. The list of variables and how the “set” command is used to

change the variables can be viewed by using the “help” command. Enter “help set” from the keyboard as shown below:

Based on help’s information shown above the user would, as an example, set the IP address by entering “set ip

199.250.185.179”. Each variable listed in help is assigned values in the same manner according to the usage given. The

window below shows all network variables being set.

help set

set:

Usage: “set <variable> <value>”

ip - The IP address of the device (ie: w.x.y.z)

The following variable can be set with this command:

netmask - The netmask for the device (ie: 255.255.255.0)

hostname - The hostname of the device (ie: w.x.y.z)

nameserver - The nameserver for the device (ie: w.x.y.z)

Note: TRIATEK Lighting ships

the BLV module with default

network settings. If the module

will be installed on a LAN these

settings must be changed. The

default settings are as follows:

IP address: 192.1.1.1

Netmask: 255.255.255.0

Gateway: 192.1.1.1

Nameserver: 192.1.1.1

hostname - The hostname of the device (ie: w.x.y.z)

nameserver - The nameserver for the device (ie: w.x.y.z)

set ip 199.250.185.179

IPOK

set netmask 255.255.255.0

NeOK

set gatgeway 199.250.185.2

GaOK

set nameserver 199.250.185.2

Name Servers set to: 199.250.185.2

All current values of the network variables

can be viewed by using the “show config”

command. This command can be used

at any point during the console session. It

can be used to view the settings before any

changes are made and after each and all

variables are set.

Hint:

Use the HyperTerminal

“show config” command

to display or validate the

current configuration

settings.

1025 Cobb Place Blvd. Suite 100 Kennesaw, GA 30144 • 800-241-9173 • www.TRIATEKlighting.com

BASnet LightView User’s Guide

Page 10 of 4105/26/2005

Setting Up BASnet LightView

Setting the Password

Unlike the network variables, the password used to enter the BLV system can only be set through the RS-232 serial

connection. Not allowing the password to be changed from the browser is a security feature that keeps the password in

a single secure location, and this in turn prevents an unintended user who has not been granted access to the physical

module from changing the password from another user’s browser. It is much easier for someone to change the password

from a user’s opened browser window than actually getting access to the physical module and an RS-232 cable.

Like the network variables, the password can be set using the “set” command, however, set’s usage with the password

variable differs from the usage of set with the network variables.

To change the password enter only “set password” and then press the Enter key on the keyboard. The program will then

bring the user through a set of prompts to change the password. The program first prompts the user for the old password:

set password

Enter old password

Error 1001 Incorrect password

Now enter the old password and press the enter key. If the old

password is entered incorrectly it will generate an error:

Each time an error is generated, “set password” must be entered again.

The program will then compare the entered password with the actual

password. If the old password is entered correctly, the program will

report “Password Verified”, and then prompt the user to enter the new

password:

set password

Enter old password

Password verified

Enter new password

Passwords can be a maximum length of any 9 keyboard characters.

Hint:

If the new password entered

is more then 9 characters

HyperTerminal will respond with

“ERROR 1000 9 character

password limit”

set password

Enter old password

Tabla de contenidos

Manuales populares de Equipo de iluminación de otras marcas

Brizo

Brizo 8SP-MU-4 Manual de usuario

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manual de usuario

IKEA

IKEA BJÖRKSPIREA Manual de usuario

Laserworld

Laserworld Evolution Series ES-400RGB Manual de usuario

Alien

Alien RG STAR Manual de usuario

EuroLite

EuroLite LED B-40 Manual de usuario

Qazqa

Qazqa Suplux SL 3 Black 103062 Manual de usuario

Commercial Electric

Commercial Electric 54568141 Manual de usuario

CREE LIGHTING

CREE LIGHTING 304 Series Manual de usuario

Goobay

Goobay 49867 Manual de usuario

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manual de usuario

Alkalite

Alkalite Krypton KT-81 Manual de usuario

Clas Ohlson

Clas Ohlson GU10 Manual de usuario

DTS

DTS DELTA 10 F Manual de usuario

ring

ring Solar Steplight Manual de usuario

One Stop Gardens

One Stop Gardens 57696 Instrucciones de montaje

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manual de usuario

SIREM

SIREM Swimeo A2 Manual de usuario