Triad InRoom Bronze PowerSub Manual de usuario
Triad Installation Guide
InWall & InRoom Subwoofers
Products
InRoom Bronze PowerSub
InRoom Silver PowerSub
InRoom Gold PowerSub
InRoom Platinum PowerSub
InWall Bronze/4 PowerSub
InWall Bronze/6 PowerSub
InWall Bronze/10 PowerSub
InWall Silver/15 PowerSub
Triad Speakers Incorporated
Thank You…
For purchasing one of Triad's high performance
Subwoofers.
Every Triad product is designed and manufactured
for both optimum performance and minimum
impact on your décor.
AllTriadPowerSubsareengineeredandhandcrafted
with pride in the United States of America.
Please take the time to review this information.
We have developed this manual so you would be
familiar with all the performance features, and
could better appreciate the superb engineering that
has been built into your Triad loudspeakers.
Thanks again and happy listening.
Larry Pexton
President
1
2
Table of Contents
Triad Speakers
PowerSub Information
and Installation Instructions Page:
Triad PowerSub Amplifier Features 3
New Construction Installation 4
Triad PowerSub Amplifier Wiring:
Two Channel Stereo 5
Triad PowerSub Amplifier Wiring:
Multi Channel Surround 6
InWall PowerSub Amplifier:
Speaker Wiring Diagram 7
Volume Control Wiring Diagram 8
Product Specifications 9
InRoom Platinum Specifications 10
InRoom Platinum PowerSub
Amplifier Features 11
InRoom Platinum PowerSub
Amplifier Wiring 12
Triad Rack Amplifier:
Adjustments/Amplifier Wiring 13
Warranty and
Dealer Information 14
LUCASFILM
Triad PowerSub Amplifier:
3
Features & Adjustments
Input Level
This controls the gain of the subwoofer amplifier when using
the left and right inputs.
Lowpass A / Lowpass B
:
Each control operates an independent 12dB per octave low
pass filter. The two filters are in parallel and their effects are
combined to achieve 24dB roll-off above the highest
common frequency.
Phase Control
The phase control adds up to 180 degrees of phase lag to the
subwoofers signal. Use it to improve the subwoofer to main
speaker blending, especially where the phase of the main
signal may have been inverted.
Left & Right Inputs (20Hz)
Use these inputs for increased frequency response below
35Hz, and where you wish to have use of the Input Level
control and high pass outputs of the sub.
Theater Input (35Hz)
Use this input with processors and A/V receivers when you
wish to maximize output above 35Hz. This is a fixed input
level designed to give maximum headroom. When using this
input, the Input Level control does not function.
High Pass Outputs:
The high Pass outputs provide a signal for your main
speaker's amplifier which has a fixed 12dB per octave high
pass filter at 100 Hz. Requires use of Left and Right inputs.
Left & Right Inputs - Using the PowerSub's Speaker to
Line Level Converter
These convert speaker level at your receiver or power
amp to the line level required for use in your
PowerSub's line level inputs.
Converter Required For Speaker Level Inputs
See Owner©s Manual
RIGHT
LEFT
THEATER
LEFT
RIGHT
INPUT
LEVEL
PHASE
CONTROL
LOWPASS
FILTER A
(HZ)
LOWPASS
FILTER B
(HZ)
MIN
MAX
110
250
110
250
0
-180
-90
LINE LEVEL
INPUTS
LINE LEVEL
HIGHPASS
OUTPUTS
3
4
65
5
5
3
4
65
5
5
New Construction Installation
4
Tools you'll need:
Power Screw Driver or Hammer
Wire Stripers
Level
Pencil or Pen
Supplies you'll need:
Triad (NCB) New Construction Bracket
Screws or Nails for attaching NCB to studs
Step One - Mark
Locate the area where the speaker will be placed
on the stud wall keeping in mind that the speaker
when installed will take up the
full wall cavity
within the NCB location (i.e. free from electrical
wires, water pipes, etc.).
Position the bracket between the desired two
studs. Take special note of the location, of the
direction arrows silk screened to the inside of the
bracket. As you face the wall these arrows should
be facing into the room.
With the level resting on top of the NCB make
sure the bracket’s top is level and mark with
pencil, the location where the NCB touches the
studs.
Step Two - Attachment
Re-check NCB alignment with marks from step
one, and attach screws through attachment holes
on NCB. Re-check squareness and adjust if
necessary.
16 inch on center studs
To Amplifiers
Step Three - Wire
Attach the wires from the source to the speaker.
You're done! Now the sheet rock people can sheet rock directly to the NCB for
a clean look. When you're ready to install the speaker, refer to step two of the
“Retro-fit Installation”
section of this manual.
Converter Required for Speaker Level Inputs
See Owner's Manual
MID
LEFT
RIGHT
THEATER
L/HP
Converter Required for Speaker Level Inputs
See Owner's Manual
80Hz
80Hz
0
o
A/V Receiver
Speaker Level Outputs
Right Left
Triad –Speaker
to Line Level
Converters
+–+–
Wire Nuts
R/HP
C
C
Speaker Level –Alternate
method if no pre-out
connection jacks are available
or using volume control.
Triad PowerSub Amplifier
Wiring Diagram (typical methods)
5
Two Channel Stereo
Triad PowerSub Amplifier
Wiring Diagram (typical methods)
6
Multi Channel Surround
Line Level –Preferred
method if subwoofer output
is available.
THX/Processor
Line Level Sub-Out
Sub Out/
THX
RCA Cable
(not supplied)
Converter Required for Speaker Level Inputs
See Owner's Manual
MID
LEFT
RIGHT
THEATER
L/HP
Converter Required for Speaker Level Inputs
See Owner's Manual
80
Hz
80
Hz
0
o
R/HP
7
InWall PowerSub:
Speaker Wiring Diagram
Triad InWall PowerSub Amplifier
with Single Speaker Enclosure:
PowerSub Amplifier:
Speaker Wiring Diagram
Speaker terminal output
–BLACK
+ RED
115v
AC
Volume Control Wiring Diagram:
Satellites & PowerSub
8
Volume Control
With Triad Satellites
& PowerSub
AMPLIFIER
LEFT RIGHT
– + – +
VOLUME
CONTROL
Converter Required for Speaker Level Inputs
See Owner's Manual
MID
LEFT
RIGHT
THEATER
L/HP
Converter Required for Speaker Level Inputs
See Owner's Manual
80
Hz
80
Hz
0
o
R/HP
TRIAD
CONVERTERS
TRIAD POWERSUB AMPLIFIER
– +
TRIAD POWERSUB
TRIAD
SATELLITES
From the volume control, "Y" the speaker wires so that one set goes to the
Satellites, and the other set goes to the Triad PowerSub amplifier through
a converter. You may only "Y" one channel if you wish to limit deep bass
by using the Theater input on the Triad PowerSub amp.
Product Specifications:
9
InRoom Bronze PowerSub
Cabinet width 13 1/2"
Cabinet height with feet 14 1/4"
Cabinet depth 13"
Shipping weight 40 lbs.
InRoom Silver PowerSub
Cabinet width 15 1/2"
Cabinet height with feet 16 1/4"
Cabinet depth 14 1/2"
Shipping weight 70 lbs.
InRoom Gold PowerSub
Cabinet width 17 1/4"
Cabinet height with feet 18 1/8"
Cabinet depth 15 3/4"
Shipping weight 76 lbs.
InWall Bronze/4 PowerSub
Cabinet width 14 1/4"
Cabinet height 19"
Cabinet depth 3 15/16"
Shipping weight 24 lbs.
InWall Bronze/6 PowerSub
Cabinet width 14 1/4"
Cabinet height 19"
Cabinet depth 5 15/16"
Shipping weight 24 lbs.
InWall Bronze/10 PowerSub
Cabinet width 13 1/2"
Cabinet height 13 1/2"
Cabinet depth 9 1/2"
Shipping weight 20 lbs.
InWall Silver/15 PowerSub
Cabinet width 14 1/4"
Cabinet height 19"
Cabinet depth 14 1/2"
Shipping weight 61 lbs.
Este manual sirve para los siguientes modelos
7
Tabla de contenidos
Otros manuales de Subwoofer de Triad
