TRENDnet TV-HW400 Manual de usuario
TV-HW400 Wall Mount
TV-HN400 Corner Mount
TV-HP400 Pole Mount
TV-HC400 Ceiling Mount
06.06.2014
TV-HN400 Corner Mount
ŸQuick Installation Guide
ŸWall mount bracket
ŸCorner adapter
ŸMounting accessories
Package Contents
1. Before You Start
1
TV-HW400 Wall Mount
ŸQuick Installation Guide
ŸWall mount bracket
ŸMounting accessories
TV-HC400 Ceiling Mount
ŸQuick Installation Guide
ŸCeiling mount bracket
ŸMounting accessories
TV-HP400 Pole Mount
ŸQuick Installation Guide
ŸWall mount bracket
ŸPole adapter
ŸPole mount hoops
ŸMounting accessories
Note:
ŸFor masonry walls, the included expansion screws must be used to secure the wall mount.
ŸFor wood/metal stud walls, self-tapping screws (not included) can be used to secure the wall
mount without the use of expansion screws.
ŸMasonry walls must be thick enough to install expansion screws.
ŸEnsure that the wall is strong enough to withstand more than 8 times the weight of the IP
camera and the mount.
2
2. TV-HW400 Wall Mount
Components
Wall Mount Bracket
5 expansion screws with nuts and washers
1. Place the arm bracket at mounting location and use it to mark screw hole locations.
2. Mark Ethernet cable hole location.
Optional: The Ethernet cable (and other cables) can be run through the indentation at the
bottom of the mounting bracket. For this installation, there is no need to mark an Ethernet
cable hole.
Mounting Accessories
Mounting
3. Drill screw holes in the wall according to the holes of the mount and a hole for cables
(optional), and then insert expansion screws into the mounting holes.
3
5. Mount bracket to the wall by aligning the 4 screw holes of the mount with the expansion
screws on the wall.
6. Secure the wall mount with 4 hex nuts and washers.
4. Pass Ethernet cable through the wall or through the indentation on the bottom of the mount.
Leave enough slack so that the cable can pass through the bracket. If you passed cables
through the wall, seal the hole with exterior grade caulking.
7. Install the speed dome to the mount. Please refer to Section 6 camera installation details.
4
3. TV-HN400 Corner Mount
Components
Wall Mount
The corner adapter must be used together with the wall mount for corner mounting
applications.
Corner Adapter
Note: Corner mounting is applicable to indoor/outdoor 90° corners with solid construction.
5 pan head screws and 5 expansion screws with nuts and washers.
Mounting Accessories
5
1. Install the corner adapter.
2. Place the corner adapter at mounting location and use it to mark screw hole locations.
Mounting
3. Mark Ethernet cable hole location (optional).
4. Drill screw holes in the wall according to the holes of the mount and a hole for cables
(optional), and then insert expansion screws into the mounting holes.
5. Pull the cables through the center hole of the corner adapter. Leave enough slack so that the
cable can pass through the bracket. If you passed cables through the wall, seal the hole with
exterior grade caulking.
6. Attach the corner adapter to the corner by aligning the 4 screw holes of the corner adapter
with the expansion screws on the corner.
7. Secure the corner adapter to the corner with nuts and washers to tighten the four expansion
screws.
Nuts and Washers
8. Secure the wall mount to the corner adapter with 4 hex screws and spring washers.
Note: When tightening the screws, it is better to compress the spring washer firmly and then
rotate it 180° to waterproof it without damaging the threads.
9. Install the dome to the mount. Please refer to Section 6 for camera installation details.
Note: For outdoor applications, please waterproof tape around the center hole for waterproofing.
water
6
4. TV-HP400 Pole Mount
Components
Wall Mount
The pole adapter must be used together with the wall mount for pole mounting applications.
Pole Adapter
Pole mounting hoops are used for securing the pole mount adapter to the pole.
Pole Mounting Hoops
7
5 pan head screws and spring washers.
Mounting Accessories
Mounting
1. Loosen the three pole mounting hoops with a flathead screwdriver.
2. Loop the hoops through the rectangular holes on the pole adapter.
3. Pull cables through the center hole. Leave enough slack so that the cable can pass through
the bracket.
4. Secure the three pole mounting hoops to the pole (5 in. or 127mm max. pole diameter), and
tighten the screws of the hoops with a flathead screwdriver.
8
5. Install the wall mount arm by securing the wall mount arm to the pole adapter with 4 hex
screws and spring washers.
6. Install the speed dome to the mount. Please refer to Section 6 for camera installation details.
Note: For outdoor applications, please use proper waterproofing measures.
9
5. TV-HC400 Ceiling Mount
Components
Ceiling Mount
Mounting Accessories
5 expansion screws with nuts and washers.
Mounting
1. Place the ceiling mount at mounting location and use it to mark screw hole locations.
2. Mark Ethernet cable hole location (optional).
Optional: The Ethernet cable (and other cables) can be run through the hole in the corner
adapter. For this installation, there is no need to mark an Ethernet cable hole.
3. Drill holes in the ceiling according to the screw holes of the mounting base, and then insert
expansion screws into the holes (masonry construction only).
4. Pull cables through the cable hole of the mounting base. Leave enough slack so that the
cable can pass through the bracket. If you passed cables through the wall, seal the hole with
exterior grade caulking.
Este manual sirve para los siguientes modelos
3
Tabla de contenidos
