TRENDnet TEW-OA14D Manual de usuario

Otros manuales para TEW-OA14D

1

Tabla de contenidos

Otros manuales de Antena de TRENDnet

TRENDnet

TRENDnet TEW-AO12O Manual de usuario

TRENDnet

TRENDnet TEW-AI07OB Manual de usuario

TRENDnet

TRENDnet TEW-AI86D Manual de usuario

TRENDnet

TRENDnet TEW-OA24D Manual de usuario

TRENDnet

TRENDnet TEW-AO10O Manual de usuario

TRENDnet

TRENDnet TEW-AO46S Manual de usuario

TRENDnet

TRENDnet TEW-AI77OB - Duo 7dBi Indoor Omni Directional... Manual de usuario

TRENDnet

TRENDnet TEW-OA24D - 24dBi Outdoor Directional Antenna B... Manual

TRENDnet

TRENDnet TEW-AO08O Manual de usuario

TRENDnet

TRENDnet TEW-IA04O Manual de usuario

TRENDnet

TRENDnet TEW-AO46S Manual de usuario

TRENDnet

TRENDnet TEW-AI75OB - 11a/g 7/5dBi Indoor Omni Directional... Manual de usuario

TRENDnet

TRENDnet TEW-AO19D Manual de usuario

TRENDnet

TRENDnet TEW-IA04O Manual de usuario

TRENDnet

TRENDnet TEW-AI75OB - 11a/g 7/5dBi Indoor Omni Directional... Manual de usuario

TRENDnet

TRENDnet TEW-AI75O Manual de usuario

TRENDnet

TRENDnet TEW-AO14D - Manual de usuario

TRENDnet

TRENDnet TEW-IA06D Manual de usuario

TRENDnet

TRENDnet TEW-AI86D Manual de usuario

TRENDnet

TRENDnet TEW-IA06D Manual de usuario

TRENDnet

TRENDnet TEW-AI86DB Manual de usuario

TRENDnet

TRENDnet TEW-AI75O Manual de usuario

TRENDnet

TRENDnet TEW-AI75OB - 11a/g 7/5dBi Indoor Omni Directional... Manual de usuario

TRENDnet

TRENDnet TEW-OA14DK Manual de usuario

Manuales populares de Antena de otras marcas

Alfa Network

Alfa Network APA-L01 Manual de usuario

Naval

Naval PR-422CA Manual de usuario

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Manual de usuario

TERK Technologies

TERK Technologies TV44 Manual de usuario

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Manual de usuario

HP

HP J8999A Manual de usuario

MobilSat

MobilSat MSP-S Manual de usuario

Steren

Steren ANT-UHF 13 Manual de usuario

Novatel

Novatel 600-G Manual de operación

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Manual de usuario

Radio Shack

Radio Shack 15-1837 Manual de usuario

CommScope

CommScope CMAX-OMFX-43M-I53 Manual de usuario

Ramsey Electronics

Ramsey Electronics DAP25 Manual de usuario

COBHAM

COBHAM SAILOR 800 VSAT Manual de uso y cuidado

Trango Systems

Trango Systems AD900-9 Manual de usuario

Steren

Steren ANT-100 Manual de usuario

Proxim

Proxim 5054-PA-23 Manual de usuario

IWCS

IWCS iriBelt II Guía de configuración

TEW-OA14D 14 dBi Outdoor High Gain Directional Panel Antenna for 2.4 ISM Band

Mounting Configuration 02262003

Installation note

Warning!

Please observe all safety rules when assembling and installing the antenna. TRENDware

will not be responsible for any damaged done by/to the antenna during/after the

installation.

Wall-Mounting

1. Read through this instruction to get an idea of the process.

2. Open the hardware bags carefully and put the hardware in separate groups. If the

hardware is pre-assembled, please disassemble it.

3. Use the two M8 x 12 screws (4) and M8 spring washers (3) to mount one of the M-Type

Stands (2) to the antenna body.

4. Securely mount the Main Stand (13) on the wall with two tapping screws (14). Use the

Plastic Wall Anchors (15) when necessary.

5. Assemble the other M-Type Stand and the Triangle Stand (12) with two M8x16 screws, two

M8 washers (6), and two M8 nuts.

6. Install the assembly in step 3 to the Main Stand (in step 2) with four M6x12 screws (10) and

four M6 washers (11). Do not tighten the screws, so you can rotate the Triangle Stand

alone the Main Stand’s curved slots.

7. Connect the antenna body’s M-Type Stand (from step 1) to the M-Type Stand in step 4 with

the M8x110 screw (7), steel tube (5), M8 washer (6), and install the M8 nut (8) on the

M8x110 loosely (loose enough for you to adjust the antenna angle).

8. Adjust the antenna angles and then tighten all the nuts/bolts. Be careful not to over tighten

the nuts and bolts.

Pole-Mounting

If you are mounting the antenna on the pole, you will need to use the Clamp Blocks, the long

bolts, and the washers (instead of the Main Stand and the Triangle Stand). The blocks, the

bolts, and the washers are not shown in the picture on the first page.

1. Read through this instruction to get an idea of the process.

2. Open the hardware bags carefully and put the hardware in separate groups. If the

hardware is pre-assembled, please disassemble it.

3. Use the two M8 x 12 screws (4) and M8 spring washers (3) to mount one of the M-Type

Stands (2) to the antenna body.

4. Assemble the other M-Type Stand and one of the Clamp Blocks with two M8x16 screws,

two M8 washers (6), and two M8 nuts.

5. Mount the assembly in step 2 and the other Clamp Block to the pole and tighten them with

the long bolts, nuts, and washers.

6. Connect the antenna body’s M-Type Stand (from step 1) to the M-Type Stand in step 3 with

the M8x110 screw (7), steel tube (5), M8 washer (6), and install the M8 nut (8) on the

M8x110 loosely (loose enough for you to adjust the antenna angle).

7. Adjust the antenna angles and then tighten all the nuts/bolts. Be careful not to over tighten

the nuts and bolts.

If you have any questions, please feel free to contact us.

Tel: +1-310-891-1100 Fax: +1-310-891-1111

E-mail: [email protected]