Travis Industries 36 CF II Manual de usuario

36 CF II Fireplace

• Operation

• Maintenance

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028- -57-5

AN I Z21.88b-2003

WARNING: If the information in these instructions is not followed e actly, a fire or

e plosion may result causing property damage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is

supplied with the appliance.

Owner's Manual

Mukilteo, WA 98275

2 Introduction

Introduction

We welcome you as a new owner of a 36 CF II gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before

operating your heater and save the manual for future reference.

Important Information

No other 36 CF II gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 36 CF II Fireplace

erial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. W

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your

Bill of ale to us.

We suggest that you attach your Bill of

ale to this page so that you will have all

the information you need in one place

should the need for service or information

occur.

Installation Warnings

• Installation requirements are printed in the 36 CF II Installation Manual (part # 100-01197).

All requirements in the installation manual must be met.

• Failure to follow all of the requirements may result in property damage, bodily injury, or

even death.

• This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

• This appliance must be installed in accordance with all local codes, if any; if not, follow

ANSI Z223.1 and NFPA 54(88).

• In Manufactured or Mobile Homes must conform with Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable,

the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1. This appliance

may be installed in Manufactured Housing only after the home is site located.

• The fireplace is designed to operate on natural gas, or propane (LP).

• All e haust gases must be vented outside the structure of the living-area. Combustion

air is drawn from outside the living-area structure.

• Notify your insurance company before hooking up this fireplace.

• The ceramic firebacks must be installed in this fireplace prior to operation.

Introduction 3

Table of Contents

Introduction and Important Information

Introduction.............................................................2

Important Information ...............................................2

Installation Warnings ................................................2

Features.................................................................3

Gas Input pecifications ........................................... 3

Safety Precautions

afety Precautions...................................................4

Operation

Before You Begin.....................................................6

Remote Control ....................................................... 6

tarting the Fireplace for the First Time....................... 8

The Two Modes of Operation ......................................8

Remote Functions....................................................10

Continuous Pilot – For Very Cold Conditions ................13

Child Protection Feature............................................ 13

Heat Bypass ...........................................................13

Normal Operating Odors............................................ 13

Power Outages.........................................................13

Maintenance

Yearly ervice Procedure.......................................... 14

Glass Frame Removal and Installation........................ 15

Log et Installation .................................................. 16

Wiring Diagram........................................................ 22

Replacement Parts List ............................................ 22

Warranty

Warranty ................................................................ 18

Optional Equipment

Optional Equipment List............................................ 24

Inde

Index...................................................................... 26

Features

• Works During Power Outages

• tandard Remote Control with Thermostat

• Realistic "Wood Fire" Look

• Convenient Remote Control

• Variable-Rate Heat Output

• Low Maintenance

Gas Input Specifications

Natural Gas Propane

Maximum BTU Input Per Hour 50,000 49,000

Minimum BTU Input on Low 28,500 26,900

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* E tinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed b

a qualified installer to prevent the possibilit

of an

explosion. Your dealer will know the requirements in your area and can inform you

of those people considered qualified. The room heater should be inspected and

cleaned before use and at least annually by a qualified service person. More

frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc.

The instructions in this manual must be strictl

adhered to. Do not use makeshift

methods or compromise in the installation. Improper installation will void the

warrant

and safet

listin

CH 4

- or -

83H

This heater is either approved

for natural gas (NG) or for

propane (LP). Burning the

incorrect fuel will void the

warranty and safety listing and

may cause an extreme safety

hazard. Direct questions

about the type of fuel used to

your dealer or installer

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

Contact

our local buildin

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance

company of this heater as

well.

If the flame becomes soot

dark orange in color, or

extremely tall, do not operate

the heater. Call your dealer

and arrange for proper

servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Gas

Do not store or use

asoline or

other flammable liquids in the

vicinity of this heater.

AAAAA

Do not operate if an

portion of

the heater was submerged in

water or if an

corrosion occurs.

Immediately call a qualified

service technician to inspect

the appliance and to replace

any part of the control system

and any gas control that has

been under water.

Safety Precautions 5

Do not place clothin

or other

flammable items on or near

the heater. Because this

heater can be controlled by a

thermostat there is a possibility

of the heater turning on and

igniting any items placed on

or near it.

ht the heater usin

the built-

in electronic igniter. Do not

use matches or any other

external device to light your

heater.

Allow the heater to cool before

carrying out any maintenance

or cleaning.

The viewin

lass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

safet

screen or

uard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify

or substitute any part of the

heater unless instructions are

given in this manual. All other

work must be done by a trained

technician. Don't modify or

replace orifices.

Prior to removing the glass,

shut off gas to the appliance

(or remove the batteries from

the battery box and shut off

electricity to the fireplace).

This prevents any chance of

accidental burner ignition

when accessing the firebox.

This

Manual

Do not throw this manual awa

This manual has important

operating and maintenance

instructions that you will need

at a later time. Always follow

the instructions in this manual.

This unit is not for use with

solid fuel

Do not place an

thin

inside

the firebox (except the

included fiber logs).

If the fiber lo

s become

damaged, replace with Travis

Industries log set.

Instruct ever

one in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut

off.

Children and adults should be

alerted to the hazards of high

surface temperature and

should stay away to avoid

burns or clothing ignition.

Young children should be

supervised when they are in

the same room as the heater.

Travis Industries, Inc.

rants

no warranty, implied or stated,

for the installation or

maintenance of your heater,

and assumes no

responsibility of any

consequential damage(s).

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section " afety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage,

bodily injury, or even death.

Remote Control

The remote control controls all of the functions on the fireplace. It can be placed inside the

holder and hung on the wall or it can be placed near the fireplace.

Set

Mode

Setting Up the Remote (Time Day Swing

The remote will need to be set up when first started or when the batteries were removed or

replaced. Follow the directions below to set the time, day, and other settings.

1. Press and hold the “ et” and “Up” arrow buttons for 5 seconds.

2. The “ROOM” temperature will blink. Use the arrow keys until °F (fahrenheit) or °C (celcius) is

displayed. Press the “ et” button to set the temperature scale.

3. The “ WING” number will blink. Use the arrow keys to select the desired swing amount (1, 2 or 3

°F, 1 or 2 °C). The swing number determines the amount of degrees the thermostat will wait

until turning on. The larger the number, the less often the thermostat will turn on and off. The

smaller the number, the more often the thermostat will turn on and off.

4. The day of the week will blink. Use the arrow keys to select the correct day. Press the “ et”

button to set the day.

5. The hour of the day will blink. Use the arrow keys to select the correct hour. Press the “ et”

button to set the hour.

6. The minute of the hour will blink. Use the arrow keys to select the correct minute. Press the

“ et” button to set the minute.

7. The AM / PM designation will blink. Use the arrow keys to select the correct setting. Press the

“ et” button to set AM / PM.

Operation 7

Remote Synchronization

The remote control is shipped pre-synchronized to the fireplace. If, however, the remote does not

work with the fireplace, follow the directions below to synchronize the remote to the fireplace.

NOTE: The fireplace must have power and the transmitter must have batteries to complete this process.

WARNING: hut the gas off to the fireplace prior to conducting this process.

1 The “Learn” switch is accessed by removing the remote holder. Inside the junction box behind the

holder you will find the “Learn” switch (see the illustration below).

2 Press the “Learn” button once. The fireplace will beep once.

3 Press the “Mode” button on the remote. The fireplace will beep five times to indicate

synchronization.

Set

Mode

AAAA

AAA

Beep

AAAA

AAA

Beep, Beep,

Beep

NOTE: Re-setting the Receiver Module

If the receiver module fails to synchronize with the remote after two attempts, you should re-set the

receiver module. To do this, hold down the LEARN button for approximately 10 seconds until the

receiver beeps 3 times. This indicates the receiver has been re-set and can be synchronized using

the instructions above.

8 Operation

Starting the Fireplace for the First Time

• Burn the heater at a high setting for an extended period (up to 48 hours). This will cure the

painted surfaces. Fumes from the paint curing and oil burning off the steel will occur. This is

normal. We recommend opening a window to vent the room.

• Condensation may appear on the glass each time you start the fireplace - this is normal.

• Blue Flames will occur on the fireplace when it first comes on. After fifteen minutes the flames

will turn a more realistic yellow and orange color.

The Two Modes of Operation

Manual Mode

In manual mode you can turn the fireplace on and off by pressing the “Mode” button until “ON” or

“OFF” appears on the remote.

Set

Mode

Set

Mode

Thermostat Mode

While in thermostat mode, the remote will

monitor the temperature and turn the fireplace

on and off to meet the desired temperature.

To turn on Thermostat Mode:

Press the “MODE” button on the remote until

“THERMO” appears on the LCD display.

To turn off Thermostat Mode:

Press the “MODE” button on the remote until

“THERMO” no longer appears on the LCD

display (the fireplace will be ON or OFF, see

“Manual Mode” above.

Set

Mode

Operation 9

Adjusting the Target Temperature of the Thermostat:

Make sure the remote is in thermostat mode. Press the up and down arrow buttons until the

desired temperature is displayed in the “ ET” box (see illustration below).

Set

Mode

WARNING: While in thermostat mode the fireplace will turn on and off to meet the temperature

demands of the remote. Do not place any items near the fireplace or conduct service without

shutting off gas to the fireplace.

WARNING: If the remote is set to a high temperature the fireplace may remain on for an extended

period of time. This may be a concern to those using LP (propane).

WARNING: If the remote is used as a thermostat for extended periods, make sure the batteries are

charged. We recommend replacing the batteries at the beginning of the heating season. If the

batteries go dead while in thermostat mode, the fireplace will shut off after 2 hours.

10 Operation

Remote Functions

Switching Between Remote Functions

By pressing the Function “FN” button, you can scroll through the following 7 functions on the

remote:

• MAIN (Main Burner)

This function will only appear when burner is on.

• REAR (Rear Burner – Not Used)

• FAN (Not Used)

• LIGHT (Not Used)

• AUX (Optional 120V Switch – Not Used)

• TIMER

This function allows the user to turn the fireplace on for a set period of time.

• PROGRAM (Programmable 7 day thermostat)

This function allows the user to program specific on/off, temperature, weekday and weekend

settings on the thermostat.

For a complete description of each function, refer to the sections on the following pages for each

individual function.

Set

Mode

Otros manuales para 36 CF II

Tabla de contenidos

Otros manuales de Chimenea de interior de Travis Industries

Travis Industries

Travis Industries 21 TRV GreenSmart Manual de usuario

Travis Industries

Travis Industries DVS Ember-Fyre 2.1 Log Manual de usuario

Travis Industries

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Manual de usuario

Travis Industries

Travis Industries 864 Clean Face GSR2 Manual de usuario

Travis Industries

Travis Industries 33 DVI Log Set Manual de usuario

Travis Industries

Travis Industries 1924 Illuminations Manual de usuario

Travis Industries

Travis Industries 564 HO Manual de usuario

Travis Industries

Travis Industries 864 TRV Manual de usuario

Travis Industries

Travis Industries DVL GSR2 NB Manual de usuario

Travis Industries

Travis Industries 430 Manual de usuario

Travis Industries

Travis Industries X-96 Manual de usuario

Travis Industries

Travis Industries DVS EF Insert Manual de usuario

Travis Industries

Travis Industries 36 CF II Manual

Travis Industries

Travis Industries 36 CF ST Manual de usuario

Travis Industries

Travis Industries 564 DF GSR2 Manual de usuario

Travis Industries

Travis Industries 564 HO GSR2 Manual de usuario

Travis Industries

Travis Industries Green Smart Manual de usuario

Travis Industries

Travis Industries 36 CF II Manual de usuario

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Manual de usuario

Travis Industries

Travis Industries 31 DVI Manual de usuario

Travis Industries

Travis Industries Flush Wood Plus Manual de usuario

Travis Industries

Travis Industries 864 TRV Manual de usuario

Travis Industries

Travis Industries Cleanface 864 Manual de usuario

Travis Industries

Travis Industries DVS FIREPLACE Manual de usuario

Manuales populares de Chimenea de interior de otras marcas

Brigantia

Brigantia 35-DVRS31N-2 Manual del propietario

Nordpeis

Nordpeis Bergen Manual de usuario

Superior

Superior BCT2536TMN Manual de usuario

Quadra-Fire

Quadra-Fire 5100I-GD-B Manual de usuario

Renaissance

Renaissance RUMFORD 1000 Manual de usuario

Lacunza

Lacunza IV-800 Manual de usuario

Baxi

Baxi 940 Instrucciones de uso

Dru

Dru Maestro 60/2 Tall RCH Manual de usuario

Diamond Fireglass

Diamond Fireglass SS-O22 Manual de usuario

HearthStone

HearthStone Windsor Bay 8830 Manual de programación

Napoleon

Napoleon ASCENT B42 Manual de usuario

Enviro

Enviro E33GI Manual de usuario

Smeg

Smeg L30 FABE Instrucciones de montaje

KEDDY

KEDDY K700 Manual de usuario

Godin

Godin 3451 Manual de usuario

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manual de usuario

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manual de usuario

Desa

Desa CCFPDFT Manual de operación