Transition Networks CPSVT2611-100 Manual de usuario

* For typical maximum cable distance, see Cable Optic section.

** Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network installation.

The stand-alone version of the media

converter is SPSVT26xx-10x. For more

information, see the SPSVT26xx-10x user’s

guide at www.transition.com.

User’s Guide

CPSVT26xx-10x

Slide-in-Module Device

•High-Speed Serial

• V.35/X.21/RS449/RS530/RS232

• Copper to Fiber

Transition Networks CPSVT26xx-10x

series high-speed serial copper-to-fiber

media converters, designed to be

installed into the Transition Networks

PointSystem™ chassis, connect V.35,

X.21, RS-449, RS-530, or RS-232

signals on copper cable, at speeds up

to 10 Mb/s, through a universal 26-pin serial interface connector to fiber-optic

cable. Transition Networks also supplies cables for connecting network equipment

to the CPSVT26xx-10x series media converter.

Cable Options . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . . .9

Cable Specifications . . . . . . . . . .10

Technical Specifications . . . . . . .12

Troubleshooting . . . . . . . . . . . . .13

Compliance Information . . . . . . .16

Part Number Port One - Copper Port Two - Duplex Fiber-Optic

CPSVT2611-100 Universal 26-pin

serial interface*

ST, 1300 nm multimode

2 km (1.2 miles)**

CPSVT2613-100 Universal 26-pin

serial interface*

SC, 1300 nm multimode

2 km (1.2 miles)**

CPSVT2614-100 Universal 26-pin

serial interface*

SC, 1310 nm single mode

20 km (12.4 miles)**

CPSVT2615-100 Universal 26-pin

serial interface*

SC, 1310 nm single mode

40 km (24.9 miles)**

CPSVT2616-100 Universal 26-pin

serial interface*

SC, 1310 nm single mode

60 km (37.3 miles)**

CPSVT2617-100 Universal 26-pin

serial interface*

SC, 1550 nm single mode

80 km (49.7 miles)**

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

* For typical maximum cable distance, see the chart on page 3.

** Typical maximum cable distance. Actual distance is dependent upon the

physical characteristics of the network installation.

Part Number Port One - Copper Port Two - Single Fiber-Optic

CPSVT2629-100 Universal 26-pin

serial interface*

SC, single mode 1310 TX / 1550nm RX

20 km (12.4 miles)**

CPSVT2629-101 Universal 26-pin

serial interface*

SC, single mode 1550 TX / 1310nm RX

20 km (12.4 miles)**

The CPSVT2629-100 and the -101 are intended to be installed

in the same network where one is the local converter and the

other is the remote converter.

CPSVT2629-102 Universal 26-pin

serial interface*

SC, single mode 1310 TX / 1550nm RX

40 km (24.8 miles)**

CPSVT2629-103 Universal 26-pin

serial interface*

SC, single mode 1550 TX / 1310nm RX

40 km (24.8 miles)**

The CPSVT2629-102 and the -103 are intended to be installed

in the same network where one is the local converter and the

other is the remote converter.

Cable Options

Supported Cable Options

The table below lists the interface standards and the cable options that are

supported for the CPSVT26xx-10x media converter.

Each cable (available from Transition Networks) is 3 meters in length and has a

male universal 26-pin serial connector at one end. The connector at the other

end is listed in the table.

Maximum Cable Lengths

The table below lists the recommended maximum cable lengths for each of the

cable options at various data rates.

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Part Number Function Connector Type

35DTE-3 V.35 DTE 34-pin Rectangular Male

35DCE-3 V.35 DCE 34-pin Rectangular Female

21DTE-3 X.21 DTE 15-pin D-sub Male

21DCE-3 X.21 DCE 15-pin D-sub Female

232DTE-3 RS-232 DTE 25-pin D-sub Male

232DCE-3 RS-232 DCE 25-pin D-sub Female

449DTE-3 RS-449 DTE 37-pin D-sub Male

449DCE-3 RS-449 DCE 37-pin D-sub Female

530DTE-3 RS-530 DTE 25-pin D-sub Male

530DCE-3 RS-530 DCE 25-pin D-sub Female

Data Rate: V.35, RS-449, or RS-530 X.21 RS232C

10 Mb/s 10 m (35 ft.) N/A N/A

6 Mb/s 19 m (65 ft.) N/A N/A

2 Mb/s 45 m (150 ft.) 15 m (50 ft.) N/A

1 Mb/s 90 m (300 ft.) 30 m (100 ft.) N/A

512 Kb/s 180 m (600 ft.) 60 m (200 ft.) N/A

256 kb/s 365 m (1200 ft.) 120 m (400 ft.) N/A

128 Kb/s 730 m (2400 ft.) 240 m (800 ft.) N/A

56 Kb/s 910 m (3000 ft.) 480 m (1600 ft.) 3 m (10 ft.)

1.2 Kb/s 910 m (3000 ft.) 910 m (3000 ft.) 15 m (50 ft.)

N/A = Not Applicable. The rates are not specified for the interface in question.

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

0 - TT = Receive CLK 8 - 768 Kb/s

1 - 56 Kb/s 9 - 1024 Kb/s

2 - 64 Kb/s A - 1544 Kb/s

3 - 112 Kb/s B - 2048 Kb/s

4 - 128 Kb/s C - 3072 Kb/s

5 - 256 Kb/s D - 4096 Kb/s

6 - 384 Kb/s E - 6144 Kb/s

7 - 512 Kb/s F - Asynchronous Mode*

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the switches and jumpers. Failure to observe this

caution could result in damage to, and subsequent failure of, the media

converter.

Set the Terminal Timing Switch

The 16-position terminal timing switch, located on the side of the media

converter’s circuit board, allows the network administrator to configure the

media converter for various network conditions.

To set the terminal timing switch, insert a small, flat-blade screwdriver or a

similar device into the recessed arrow on the switch. Gently rotate the switch

to the position required for the site installation.

The table below lists the conditions for each setting of the terminal timing

switch:

* Setting “F” overrides the software mode (see page 6) and sets the media

converter to asynchronous mode.

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Installation -- Continued

Set the Loop-Back Switch

The loop-back switch is located on the front panel of the media converter and

is used to debug network faults. (See “Troubleshooting” section for

examples.)

To set the switch, use a small flat-blade

screwdriver or a similar device.

Norm Set the switch to “Norm” for

normal operation.

Loop Set the switch to “Loop” to

enable both fiber and copper

loop-back.

The two drawings below illustrate the data path for both normal mode and

loop-back mode:

Normal Mode Loop-Back Mode

The drawing below indicates the data path during loop-back mode for each of

the pins on the copper 26-pin connector.

TxD (1,14)

(To DCD on other Converter)

(From DCD on other Converter)

Loop Back Mode

High Speed Serial Converter

RxD (3,16)

TxCE (24,11)

RxC (17,9)

TxC (15,12)

RTS (4,19)

CTS (5,13)

DTR (20,23)

DRS (6,22)

DCD (8,10)

LL(18)

NormLoop

Normal Operation

Fiber& CopperLoop Back

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation -- Continued

Set the Jumpers

The CPSVT26-10x has three jumpers located on the circuit board. To set any

of the three jumpers, use small needle-nosed pliers or similar device to move

the jumper(s) to the desired position(s). (See pages 6 and 7.)

Hardware/Software Jumper (J4)

The Hardware/Software jumper (J4) is located on

the circuit board and is the jumper that is

nearest the rear connector of the media

converter (see the photo to the right).

Hardware The terminal timing switch

controls the terminal timing

function. The loop-back switch

controls the loop-back function.

Software The terminal timing switch and

the loop-back switch are

disabled. These two functions

are controlled by the most-

recently saved, on-board

microprocessor settings.

NOTE: Setting the terminal timing switch to “F” overrides the software mode

and sets the media converter to asynchronous mode. (See page 4.)

Remote Management

The CPSVT26xx-10x can remotely manage the SPSVT26xx-10x (the stand-

alone version of the media converter) or another CPSVT26xx-10x installed in

a Transition Networks PointSystem™ chassis.

For example, a local CPSVT2611-100 converter (that is installed in a managed

PointSystem™ chassis) is connected, via fiber, to a remote SPSVT2611-100

converter. An example of a managed single-fiber network has a local

CPSVT2629-100 converter connected, via fiber, to a remote SPSVT2629-101.

The SNMP section (on page 9) lists the commands that can be used to monitor

and manage both the local and remote media converters.

Note: In a managed network, both the local and remote media converters

must be set to “software” mode (see above).

Software Mode

Hardware Mode

Rear Connector

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Installation -- Continued

Receive (RX) Clock Polarity Jumper (J6)

The RX Clock Polarity jumper (J6), located near the front panel of the circuit

board, selects the polarity of the receive clock.

Position A The receive data is sampled on the

rising edge of the receive clock.

Position B The receive data is sampled on the

falling edge of the receive clock.

Transmit (TX) Clock Polarity Jumper (J7)

The TX Clock Polarity jumper (J7), also located near the front panel of the

circuit board, selects the polarity of the transmit clock.

Position A The transmit data is sampled on the

rising edge of the receive clock.

Position B The transmit data is sampled on the

falling edge of the receive clock.

This drawing illustrates “rising edge” and “falling edge” for clock polarity.

Position B

Position A

Position B

Position A

J7- TX Clock Polarity Jumper

J6- RX Clock Polarity Jumper

Front Panel

Installation -- Continued

Install the Slide-In-Module

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when installing the CPSVT26xx-10x slide-in-module media

converter. Failure to observe this caution could result in damage to, and

subsequent failure of, the media converter.

1. Carefully slide the slide-in-module into the installation slot, aligning the

module with the installation guides.

2. Ensure that the module is firmly seated against the back of the chassis.

3. Push in and rotate the attached panel fastener screw clockwise to secure

the module to the chassis front.

Install the Fiber Cable

1. Locate or build fiber optic cable with male, two-stranded TX to RX

connectors installed at both ends.

2. Connect the fiber cables to the CPSVT26xx-10x media converter as

described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the other device (another media converter,

hub, etc.) as described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Connect fiber cable

to media converter

as shown.

Connect fiber cable

to other device

(media converter,

hub, etc.) as shown

Media Converter

PointSystem Chassis

Panel Fastener

Slot

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Installation -- Continued

Install the Copper Cable

1. Connect the high-speed serial cable to the media converter by

connecting the cable’s copper connector to the converter’s copper port.

2. Ensure that the cable screwlocks are tightened securely. Failure to

observe this caution could cause data transfer to fail.

3. Connect the other end of the high-speed serial cable to the other network

device (cable router, CSU, etc.).

Operation

Status LEDs

Use the status LEDs to monitor the CPSVT26xx-10x media

converter operation in the network.

PWR (on) The media converter is connected to

external power.

FL (on) The fiber link is up.

(flashing) The fiber link is in loop-back mode.

CL (on) The copper link is up.

(flashing) The copper link is in loop-back mode.

(In asynchronous mode, the CL LED may flash if

the data rates fall below 300 cycles per second.)

SNMP

See the on-line documentation that comes with Transition Networks

FocalPoint™ software for applicable commands and usage.

Use SNMP at an attached or remote terminal to monitor:

•

Media converter Power

• Fiber lock status (local only)

• Hardware / software mode (local / remote)

• Copper speed (local / remote)

• Loop-back status (local / remote)

• Clock polarity setting (local / remote)

• Cable type (local / remote)

Also, use SNMP to enter network commands that:

• Bootload the firmware (local only)

• Enable/disable loop-back (local / remote)

• Copper speed (local / remote)

• Power-down the media converter

CPSVT

NORM LOOP

CL FL PWR

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Cable Specifications

Fiber Cable

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

CPSVT2611-100 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

CPSVT2613-100 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

CPSVT2614-100 1310 nm single mode

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

CPSVT2615-100 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

CPSVT2616-100 1310 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CPSVT2617-100 1550 nm single mode

Fiber-optic Transmitter Power: min: -5.0 dBm max: 0.0 dBm

Fiber-optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 29.0 dB

CPSVT2629-100 1310 nm (TX) / 1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

CPSVT2629-101 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

CPSVT2629-102 1310 nm (TX) / 1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

CPSVT2629-103 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meet Class I Laser safety requirements

per IEC-825/CDRH standards and comply with 21 CFR1040.10 and

21CFR1040.11.

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Cable Specifications -- Continued

Copper Cable

• Copper twisted-pair, 28 AWG, 120 Ohm, 12 pf/foot capacitance (max)

• Nominal DC resistance: 65.0 ohms per 1000 feet (each conductor)

• Shield type: Aluminum Foil-Polyester Tape/Braid Shield with drain wire

• Standard Cable length: 3 m (10 ft.)

The five high-speed serial cables (available from Transition Networks) that are

compatible with the 26-pin copper port on the CPSVT26xx-10x media

converter are listed below.

RS-232

RS-449

V.35

X.21

RS-530

Note: Please refer to the cable specification documentation on-line at

www.transition.com.

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Technical Specifications

For use with Transition Networks Model CPSVT26xx-10x or equivalent

Standards: V.35, RS-530, RS-449, RS-232, X.21

Data Rate: 1.2 Kb/s to 10 Mb/s

Dimensions: 3.4" x 5.0" x 0.87" (86 mm x 182 mm x 22 mm)

Weight: 3 oz. (91 g) (approximate)

Power Consumption: 5.0 Watts

MTBF 401,864 hours

(MIL217F2 V5.0) (MIL-HDBK-217F)

1,201,311 hours (Bellcore7 V5.0)

Environment: Tmra*: 0 to 50°C (32 to 122°F)

Storage Temperature: -15 to 65°C (5 to 149°F)

Humidity: 10 to 90%, non condensing

Altitude: 0 to 10,000 feet

Warranty: Lifetime

*Manufacturer’s rated ambient temperature. Tmra range for this slide-in-module

depends on the physical characteristics and the installation configuration of the

Transition Networks PointSystem™ chassis in which this slide-in-module will be

installed.

For the most up-to-date information on the CPSVT26xx-10x media converter, see

the user’s guide on-line at www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into

beam or view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other

than those specified herein may result in hazardous radiation exposure.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Troubleshooting

If the media converter fails, isolate and correct the fault by determining the answers

to the following questions and then taking the indicated action:

1. Is the PWR LED on the media converter illuminated?

• Is the media converter installed properly in the chassis?

• Is the power cord properly installed in the chassis and in the external

power source and does the external power source supply power?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the CL LED on the media converter illuminated?

• Are the copper cables connected properly?

• Is the device attached to the media converter via the copper cable

working properly?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the FL LED on the media converter illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the media converter are connected

to the RX and TX ports, respectively, on the other device.

• Are both media converters (connected via the fiber cables) in the same

mode (synchronous or asynchronous)?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Are the CL and FL LEDs on the media converter flashing (indicating

loop-back mode)?

• Disable the loop-back function. In hardware mode, set the loop-back

switch to NORM (normal). In software mode, click “disable” in the

loop-back function.

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 5.

5. Is data transfer failing?

YES

• Are the clock input and output polarity correct?

• Are the correct copper cables installed for the data format?

• Is the mode on the other device correct (synchronous/asynchronous)?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

• Proceed to step 6.

CPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

6. Is data transfer failing?

YES

• Verify the local copper connection by starting a local copper loop-

back (hardware mode: set the loop-back switch on the local media

converter to “loop”, software mode: enter the local copper loop-back

command) and then use a bit error test unit to run a bit error test.

• Verify the local fiber connection by starting a remote fiber loop-back

(hardware mode: set the loop-back switch on the remote media

converter to “loop”, software mode: enter the remote fiber loop-back

command) and then use a bit error test unit to run a bit error test.

• Verify the remote copper connection by starting a remote copper

loop-back (hardware mode: set the loop-back switch on the remote

media converter to “loop”, software mode: enter the remote copper

loop-back command) and then use a bit error test unit to run a bit

error test.

• Verify remote fiber connection by starting a local copper loop-back

(hardware mode: setting the loop-back switch on the local media

converter to “loop”, software mode: enter the local fiber loop-back

command) and then use a bit error test unit to run a bit error test.

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

reppoCrebiFreppoC Local

Device

Remote

Device

reppoCrebiFreppoC Remote

Device

Local

Device

reppoCrebiFreppoC Local

Device

Remote

Device

reppoCrebiFreppoC Remote

Device

Local

Device

Declaration of Conformity

Name of Mfg: Transition Networks

10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.

Model: CPSVT26xx-10x Series Devices

Part Number(s): CPSVT2611-100, CPSVT2613-100, CPSVT2614-100,

CPSVT2615-100, CPSVT2616-100, CPSVT2617-100,

CPSVT2629-100, CPSVT2629-101, CPSVT2629-102,

CPSVT2629-103

Regulation: EMC Directive 89/336/EEC

Purpose: To declare that the CPSVT26xx-10x to which this declaration refers is

in conformity with the following standards.

CISPR 22: 1993; EN 55022:1998+A1:2000 Class A; EN 55024: 1998; FCC Part 15

Subpart B; 21CFR subpart J; EN 61000-3-2:1995:A14:2000; EN 61000-3-3:1995

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive(s) and Standard(s).

July, 2008_____

Stephen Anderson, Vice-President of Engineering Date

[email protected] -- Click the “Transition Now” link for a live Web chat. 15

Technical Support

Technical support is available 24 hours a day.

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition Now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

10900 Red Circle Drive

Minnetonka, MN 55343, U.S.A.

telephone: 952-941-7600

toll free: 800-526-9267

fax: 952-941-2322

Compliance Information

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be required to correct the

interference at the user's own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus

set out on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites

applicables aux appareils numériques de la Class A prescrites dans le Règlement sur le

brouillage radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb

dieses Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für

Gegenmaßnahmen verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer

des interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures

spécifiques appropriées.

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

means - graphic, electronic, or mechanical - without written permission from Transition

Networks.

Printed in the U.S.A. 33235.F

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Convertidor de medios de Transition Networks

Transition Networks

Transition Networks CFETF1011-205 Manual de usuario

Transition Networks

Transition Networks F-SM-MM-06(XL) Manual de usuario

Transition Networks

Transition Networks SPS-1872-CC Manual de usuario

Transition Networks

Transition Networks CBFTF1011-110 Manual de usuario

Transition Networks

Transition Networks M/GE-ISW-SFP-01-PD Manual de usuario

Transition Networks

Transition Networks SGPOE1013-100 Manual de usuario

Transition Networks

Transition Networks E-100BTX-FRL-03(SC) E-100BTX-FRL-03(SM) Manual de usuario

Transition Networks

Transition Networks FXC1115T Manual de usuario

Transition Networks

Transition Networks E-CX-TBT-04 Manual de usuario

Transition Networks

Transition Networks Milan Raven Series Manual de usuario

Transition Networks

Transition Networks E-MCR-02 Manual de usuario

Transition Networks

Transition Networks SISTG10 211-LR Series Manual de usuario

Transition Networks

Transition Networks SGFEB1013-100 Manual de usuario

Transition Networks

Transition Networks M/GE-xSW-SFP-01-xx-U Series Manual de usuario

Transition Networks

Transition Networks SCSCF3011-100 Manual de usuario

Transition Networks

Transition Networks SI-IES-111D-LRT Manual de usuario

Transition Networks

Transition Networks SSETF1011-205 Manual de usuario

Transition Networks

Transition Networks J/FE-CF-04 SMLC Manual de usuario

Transition Networks

Transition Networks E-100BTX-FX-05(LC) Manual de usuario

Transition Networks

Transition Networks SISTF10xx-111-LR(T) Manual de usuario

Transition Networks

Transition Networks CETCT1020-100 Manual de usuario

Transition Networks

Transition Networks M/GE-SW-SFP-01-U Series Manual de usuario

Transition Networks

Transition Networks CSDTF1011-100 Manual de usuario

Transition Networks

Transition Networks CBFTF1011-100 Manual de usuario

Manuales populares de Convertidor de medios de otras marcas

SoundTraxx

SoundTraxx Blunami BLU-2200 Manual de usuario

SPROLINK

SPROLINK VA1 Manual de usuario

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manual de usuario

Nikon

Nikon AF-S TC-20E III Manual de usuario

Axis

Axis AXIS Q7406 Manual de usuario

Omega

Omega TAC80B-J Manual de usuario

Zoom

Zoom Thunderbolt TAC-2R Manual de usuario

OST

OST iConverter 10/100M Manual de usuario

Vertiv

Vertiv Netsure Manual de usuario

birddog

birddog MINI Manual de usuario

Roland

Roland GI-10 Manual de usuario

Wallenstein

Wallenstein WX310 Manual de usuario

Pace

Pace MSS 200-1 Manual de usuario

Solar Converters

Solar Converters EQ 12/24-50 Manual de usuario

CYP

CYP EL-7400V Manual de usuario

TIE

TIE MIDI 1i1o Manual de usuario

DCS

DCS Vivaldi Upsampler Manual de usuario

Westermo

Westermo MCW-211 SERIES Manual de usuario