Transcell Technology TI-1680 Manual de instrucciones

TI-1680

DIGITAL WEIGHT INDICATOR

Setup / Operation Manual

Revision 1.31 975 Deerfield Parkway Buffalo Grove, IL 60089

March 22, 2013 Tel (847) 419-9180 Fax (847) 419-1515

http://

www.transcell.

com

TABLE OF CONTENTS

Page

INTRODUCTION.................................................................................................................................................1

FCC NOTE...........................................................................................................................................................1

INSTALLATION...................................................................................................................................................1

PREPARATION ................................................................................................................................................1

CONNECTIONS................................................................................................................................................2

CONNECTING THE WEIGH PLATFORM.......................................................................................................2

CONNECTING THE SERIAL I/O DEVICE (COM1)......................................................................................2

CONNECTING THE CONTROL I/O ..............................................................................................................3

CONNECTING THE RS-232 PORT (COM2)................................................................................................3

CONNECTING THE OPTIONAL WLAN (COM2).........................................................................................3

CONNECTING THE OPTIONAL RS-485 (COM2).......................................................................................4

CONNECTING THE OPTIONAL BLUETOOTH (COM2).............................................................................4

CONNECTING THE OPTIONAL ANALOG OUTPUT..................................................................................4

CONNECTING THE POWER SUPPLY.........................................................................................................4

CONFIGURATION..............................................................................................................................................5

OVERVIEW......................................................................................................................................................5

ACCESSING THE MENUS.............................................................................................................................5

MENU STRUCTURE.......................................................................................................................................6

SETUP MENU DESCRIPTIONS....................................................................................................................7

SETUP MENU PROCEDURES....................................................................................................................10

USER MENU DESCRIPTIONS....................................................................................................................11

USER MENU PROCEDURES......................................................................................................................13

BATCH MENU DESCRIPTIONS..................................................................................................................15

BATCH MENU PROCEDURES...................................................................................................................15

EXITING THE MENUS..................................................................................................................................16

CALIBRATION...................................................................................................................................................17

CALIBRATION OVERVIEW.........................................................................................................................17

ZERO CALIBRATION (F16).........................................................................................................................17

SPAN CALIBRATION (F17).........................................................................................................................17

VIEW CALIBRATION VALUES (F18).........................................................................................................18

KEY-IN ZERO CALIBRATION VALUE (F19).............................................................................................19

KEY-IN SPAN CALIBRATION VALUE (F20).............................................................................................19

DISPLAY........................................................................................................................................................20

KEYBOARD...................................................................................................................................................21

FUNCTION KEYS......................................................................................................................................21

NUMERIC KEYS........................................................................................................................................22

GENERAL SCALE OPERATION ................................................................................................................22

WEIGHING AN ITEM.................................................................................................................................22

ENTERING A KNOWN TARE WEIGHT..................................................................................................23

CLEARING A TARE WEIGHT..................................................................................................................23

ENTERING AN ID NUMBER....................................................................................................................23

PROGRAMMING SET POINTS ...............................................................................................................23

PROGRAMMING OVER/UNDER VALUES............................................................................................24

ADVANCED SCALE OPERATION..............................................................................................................25

APPLICATION (F30) SUMMARY ............................................................................................................25

STANDARD OUTPUTS ............................................................................................................................26

ACCUMULATION APPLICATION (F30 = 1)...........................................................................................26

REMOTE DISPLAY APPLICATION (F30 = 2)........................................................................................26

PIECE COUNT APPLICATION (F30 = 3)................................................................................................26

PERCENTAGE APPLICATION (F30 = 4)...............................................................................................27

HOLD APPLICATION (F30 = 5)...............................................................................................................28

CHECKWEIGHING APPLICATION (F30 = 6) ........................................................................................28

BATCHING APPLICATION (F30 = 7) .....................................................................................................29

TRUCK WEIGH IN/WEIGH OUT APPLICATION (F30 = 8)...................................................................30

LEGAL FOR TRADE SEALING ......................................................................................................................31

iii

APPENDIX A: SPECIFICATIONS...................................................................................................................32

APPENDIX B: SERIAL PORT INFORMATION..............................................................................................33

SERIAL PORT MODES................................................................................................................................33

DEMAND DUPLEX MODE.......................................................................................................................33

CONTINUOUS DUPLEX MODE ..............................................................................................................33

AUTO PRINT MODE.................................................................................................................................33

OUTPUT STRING..........................................................................................................................................34

TEXT PRINT TICKET................................................................................................................................35

STRING FORMAT 1 (Condec Demand String).....................................................................................36

STRING FORMAT 2 (Condec Continuous String) ..............................................................................37

APPENDIX C: DISPLAYED ERROR CODES....................................................................................................39

APPENDIX D: WIRING EXTERNAL OUTPUT RELAYS .................................................................................40

OUTPUTS......................................................................................................................................................40

INPUTS...........................................................................................................................................................41

APPENDIX E: INFO ON ANALOG OUTPUT OPTION .....................................................................................42

The information contained herein is the property of Transcell Technology and is supplied without liability for errors or omissions. No

part may be reproduced or used except as authorized by contract or other written permission. The copyright and the foregoing

restriction on reproduction and use extend to all media in which the information may be embodied.

Contents subject to change without notice.

INTRODUCTION

The TI-1680 Digital Indicator is a multi-purpose, industrial grade weight indicator. The Table below

summarizes the main physical parameters.

MODEL

DISPLAY

TYPE

ENCLOSURE

TYPE

POWER SOURCE

TI-1680 LED Stainless Steel 100-240 VAC, 50/60 Hz 30W

The unit can readout up to 50,000 display divisions and can supply enough current for up to 8-350Ωload

cells. All setup parameters may be entered via the front panel keys, including calibration.

If your Model TI-1680 Series Digital Indicator is part of a complete scale or has already been installed for

you, then you may skip to the operating instructions. Prior to using the indicator, please read this manual

carefully and completely. Store the manual in a safe and convenient place so it will be available if you

have questions concerning the operation of the scale.

FCC NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Subpart J of Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his/her own expense.

INSTALLATION

PREPARATION

Any precision instrument requires a suitable environment in which to operate as intended. Please review

each of the following prior to installation:

Electrical Power

The TI-1680 indicator has been designed to operate from 100 to 240 VAC at 50/60 Hz. All units ship with

the appropriate power plug for its area of intended use.

To avoid electrical noise interference and/or stray AC electrical transients, try to operate the indicator from

a circuit separate from any equipment containing inductive devices such as a contactor coil, solenoid,

relay coil, or motor. Be sure to use shielded cables for the load cell connections (ground shield wire at

indicator) and run these cables away from your AC/DC power cables if possible.

In extreme cases, it may be necessary to install surge suppressors, line conditioners or even UPS

(Uninterruptible Power Supplies) systems (not included).

Environment

-Avoid installing the indicator in areas of direct sunlight or high humidity

-Avoid sudden temperature change – if this is unavoidable allow equipment to ‘soak’ at a constant

temperature for at least three hours before use

-Ensure that steady, clean AC power is available to the unit

Remember that the installer is ultimately responsible to assure that a particular

installation will be and remain safe and operable under the specific conditions

encountered.

CONNECTIONS

For the TI-1680 model, the rear cover must first be removed to make the appropriate connections to the

weigh platform, serial I/O device and other peripheral equipment. To remove the rear cover, simply

remove the six acorn nuts that secure it to the main enclosure and set aside.

Caution! Disconnect power source from indicator prior to removing rear cover.

CONNECTING THE WEIGH PLATFORM

The TI-1680 indicator contains a connection terminal on the main board for connection to the load cell

cable or junction box. Connect your shielded load cell cable (not included) to the appropriate terminal on

the main board. NOTE: 6-wire connection is a factory option

Load Cell Connector J1

Pin No.

Wire Name

Pin No.

Wire Name

1 + Excitation (E+) 5 + Signal (S+)

2 + Sense (SEN+) 6 - Signal (S-)

3 - Excitation (E-) 7 Shield (SH)

4 - Sense (SEN-)

CONNECTING THE SERIAL I/O DEVICE (COM1)

The TI-1680 indicator contains a connection terminal on the main board for connection to a serial I/O

device, e.g. ticket printer. You can choose either RS-232 or USB 2.0 - but not both at the same time.

For USB, the TI-1680 is considered a peripheral device, i.e. the host device supplies the power (VBUS).

Try not to exceed cables lengths of 5 m (16 ft).

Selection between RS-232 and USB is made via JP4, JP5, JP7 and JP8:

Function

JP5

JP7

JP8

RS-232 SHUNT OPEN SHUNT OPEN

USB OPEN SHUNT OPEN SHUNT

NOTE: For remote display emulation application (F30=2), use COM2 only

Connection assignments for COM1 RS-232 communication terminal on the TI-1680 are shown below.

RS-232 Connector J9

Pin No.

Wire Name

Pin No.

Wire Name

1 RXD 4 RTS

2 TXD 5 Ground

3 CTS

Connection assignments for COM1 USB communication terminals on the TI-1680 are shown below.

USB Connector J6

Pin No.

Wire Name

Wire Color

Pin No.

Wire Name

Wire Color

1 VBUS Red 3 D+ Green

2 D- White 4 GND Black

CONNECTING THE CONTROL I/O

The TI-1680 indicator features one remote input and four output terminals for connection to process

control equipment. A +5VDC terminal is also included for connection to the outputs if an external supply is

not available.

The outputs are labeled OUT1-OUT4. The single remote input is triggered by simple contact closure. For

suggested wiring diagrams, see Appendix D.

Connection assignments for all control I/O terminals on the TI-1680 are shown below.

Control I/O Connector J4

Pin No.

Wire Name

Pin No.

Wire Name

1 +5V 6 OUTPUT1

2 GND 7 OUTPUT2

3 INPUT 8 OUTPUT3

4 GND 9 OUTPUT4

5 CATCHDIODE

CONNECTING THE RS-232 PORT (COM2)

The J11 terminal allows for a 2nd RS-232 port. This is realized by an optional board soldered to J11 pads.

RS-232 Connector J9A

Pin No.

Wire Name

Pin No.

Wire Name

1 RXD 4 RTS

2 TXD 5 Ground

3 CTS

CONNECTING THE OPTIONAL WLAN (COM2)

The J11 terminal allows for an optional WLAN (Wireless Ethernet) communications port. This is realized

by an optional board soldered to J11 pads.

CONNECTING THE OPTIONAL RS-485 (COM2)

The J11 terminal allows for an optional half duplex, Multipoint EIA-RS-485 communications port. It is also

compatible with it is compatible with TIA/EIA-422-B.This is realized by an optional board soldered to J11

pads.

RS-485 Connector J2

Pin No.

Wire Name

1 Tx+/Rx+ (AA)

2 Tx-/Rx- (BB)

CONNECTING THE OPTIONAL BLUETOOTH (COM2)

The J11 terminal allows for an optional Bluetooth port. This is realized by an optional board soldered to

J11 pads.

CONNECTING THE OPTIONAL ANALOG OUTPUT

The J3 terminal allows for an optional analog out. This is realized by an optional board soldered to J3

pads.

Please see Appendix E for more information on this option.

CONNECTING THE POWER SUPPLY

The TI-1680 indicator ships with an AC line cord attached to the indicator. It has been pre-wired on J7 at

the factory. Simply plug the unit into a standard wall outlet.

CONFIGURATION

OVERVIEW

The indicator contains two main configuration menus:

•The Setup (“F”) menu, which configures and calibrates the indicator to your weigh platform

•The User (“A”) menu, which configures the serial communication ports and enables some

user options

•The Batching (“B”) menu, which configures the I/O for process control and checkweighing

functions

All menus consist of several menu selections, each with their own sub-menu of selections or

programming procedures. To configure the indicator you must first enter the appropriate menu mode.

Once there, four of the front panel keys become directional navigators to move around in the menus, and

one key is used to save or SET the selections.

ACCESSING THE MENUS

To access the Setup (“F”) menu:

1. Power off the indicator.

2. Locate the slide switch on the rear cover and move it to the opposite position.

NOTE: A metal plate conceals the slide switch; remove the two drilled-head screws and cover

plate to access the slide switch.

3. Power on the indicator.

The display shows “ PASS_” to indicate that you need to enter a password to access Setup Menu

mode.

4. Key-in the password (1397) and then press Enter key

The display shows ” F 1” to indicate that you are in Setup Menu mode.

To access the User (“A”) menu:

1. Power off the indicator.

2. Locate the slide switch on the rear cover and move it to the opposite position.

NOTE: A metal plate conceals the slide switch; remove the two drilled-head screws and cover

plate to access the slide switch.

5. Power on the indicator.

The display shows “ PASS_” to indicate that you need to enter a password to access User Menu

mode.

3. Key-in the password (1793) and then press SET (MODE) key

The display shows ” A 1” to indicate that you are in User Menu mode.

To access the Batch (“B”) menu:

1. Power off the indicator.

2. Locate the slide switch on the rear cover and move it to the opposite position.

NOTE: A metal plate conceals the slide switch; remove the two drilled-head screws and cover

plate to access the slide switch.

6. Power on the indicator.

The display shows “ PASS_” to indicate that you need to enter a password to access User Menu

mode.

3. Key-in the password (1234) and then press SET (MODE) key

The display shows ” B 1” to indicate that you are in Batch Menu mode.

MENU STRUCTURE

All menus consist of a top level (heading) and a secondary level. The top level contains the code (e.g. F1)

for the parameter to be configured. The secondary level contains the selection list or allows access to a

programming sequence.

Use the directional keys to move around in the Menu Structure shown below.

Grads

10 80

Sampling Rate

Selection List

Etc.

1. To move to a new heading, use the TARE (left) or PRINT (right) key to move right or

left in the Menu.

2. To move to the selection or programming level, press the ZERO (down) key once. The

currently saved selection is shown.

3. To view the available selections for the current heading, use the TARE (left) or PRINT

(right) key to move through the selection field.

4. To save a new selection, press the MODE (Set) key .To exit without saving, press the

UNITS (up) key to return to the current heading.

5. Repeat Steps 2 through 5 until the Menu is programmed.

To exit any setup Menu, press the C/CE key. To exit all the way out return the slide switch to its original

position.

SETUP MENU DESCRIPTIONS

This section provides more detailed descriptions of the selections found in the Setup Menu Chart. Factory-

set defaultsare shown in bold; (NA) for North America and (€)for Europe.

NOTE: Some selections are subject to local legal metrology regulations

CODE/NAME DESCRIPTION SELECTION LIST

Graduations Specifies number of full-scale graduations, i.e. capacity ÷ division.

For example, if scale is to be 5000 lb x 1 lb, then F1 should be set to

5000 (5000 ÷ 1). Value should be consistent with legal regulations

and environmental limits on the useful system resolution. Pressing

the ZERO key to scroll down one level begins the sequence.

Key-in

100 - 50000

10000 (NA)

6000 (€)

Sampling Rate Sets the sampling rate in Hertz (measurements per second). Use

10 Hz for most applications or 80 Hz for extra fast response time 10√

√√

√(NA/€) 80

Zero Track

Band

Selects the range within which the scale will automatically zero. Note

that the scale must be in standstill to automatically zero. Selections

are in display divisions per second (d/s).

0.5d √

√√

√(NA/€)

Zero Range Selects the range (expressed as a percentage of full scale capacity)

within which the scale may be zeroed. Note that the indicator must be

in standstill to zero the scale.

100% (NA)

1.9%

2% (€)

20%

Motion Band Sets the level at which motion is detected. If motion is not detected,

the scale can process a Print or Zero command. Maximum value

varies depending on local regulations. Expressed as scale divisions

per second (d/s). Pressing the ZERO key to scroll down one level

begins the sequence.

Key-in

0.0d/s – 32.0d/s

1.0d/s (NA/€)

Digital Filter Averages weight readings to produce higher stability. Choose the

speed that works best for your application.

“FAST” = Fast “nnEd” = Medium “SLo” = Slow

FAST

nnEd√

√√

√(NA/€)

SLo

Overload Limit Selects the formula which determines the point at which the indicator

shows overload. All selections are based on the primary unit selected

in F8.

"FS" = Full scale capacity.

FS + 2% (NA)

FS + 5%

FS + 1d

FS + 9d (€)

Calib. Unit Selects the primary base unit to be used in the calibration process.

Also the default unit for normal operation.

"1" = primary unit is lb. "2" = primary unit is in kg.

1 (NA)

2 (€)

Display

Divisions

Determines the desired weight increments. Value should be

consistent with legal requirements. 1 (NA)

5 (€)

F10

Decimal Pt. Determines location of the decimal point. 0 (NA) 0.0 (€)

0.00 0.000

0.0000 00

Otros manuales para TI-1680

Tabla de contenidos

Otros manuales de Panel táctil de Transcell Technology

Transcell Technology

Transcell Technology NEPTUNE 4500 Manual de instrucciones

Transcell Technology

Transcell Technology TI-500 RF Series Guía del usuario

Transcell Technology

Transcell Technology TI-500 RF Series Manual de usuario

Transcell Technology

Transcell Technology TI-1500B Manual de lista de piezas

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

Advantech

Advantech TPC-30 Series Manual de usuario