Trane WSC120E Manual del propietario

January 2010 RT-SVX23E-EN

Installation

Operation

Maintenance

Packaged Heat Pump

3 Through 10 Ton

Model Numbers

WSC036E - WSC120E

Warnings, Cautions and Notices

Warnings, Cautions and Notices. Note that warnings, cautions and notices appear at

appropriate intervals throughout this manual. Warnings are provided to alert installing contractors

to potential hazards that could result in personal injury or death. Cautions are designed to alert

personnel to hazardous situations that could result in personal injury, while notices indicate a

situation that could result in equipment or property-damage-only accidents.

Your personal safety and the proper operation of this machine depend upon the strict observance

of these precautions.

Important

Environmental Concerns!

Scientific research has shown that certain man-made chemicals can affect the earth's naturally

occurring stratospheric ozone layer when released to the atmosphere. In particular, several of the

identified chemicals that may affect the ozone layer are refrigerants that contain Chlorine, Fluorine

and Carbon (CFCs) and those containing Hydrogen, Chlorine, Fluorine and Carbon (HCFCs). Not all

refrigerants containing these compounds have the same potential impact to the environment.

Trane advocates the responsible handling of all refrigerants-including industry replacements for

CFCs such as HCFCs and HFCs.

Responsible Refrigerant Practices!

Trane believes that responsible refrigerant practices are important to the environment, our

customers, and the air conditioning industry. All technicians who handle refrigerants must be

certified. The Federal Clean Air Act (Section 608) sets forth the requirements for handling,

reclaiming, recovering and recycling of certain refrigerants and the equipment that is used in these

service procedures. In addition, some states or municipalities may have additional requirements

that must also be adhered to for responsible management of refrigerants. Know the applicable

laws and follow them.

Overview of Manual

Note: One copy of this document ships inside the control panel of each unit and is customer

property. It must be retained by the unit’s maintenance personnel.

This booklet describes proper installation, operation, and maintenance procedures for air cooled

systems. By carefully reviewing the information within this manual and following the instructions,

the risk of improper operation and/or component damage will be minimized.

It is important that periodic maintenance be performed to help assure trouble free operation. A

maintenance schedule is provided at the end of this manual. Should equipment failure occur,

contact a qualified service organization with qualified, experienced HVAC technicians to properly

diagnose and repair this equipment.

ATTENTION: Warnings, Cautions and Notices appear at appropriate sections throughout

this literature. Read these carefully.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, could

result in minor or moderate injury. It could also be used to alert against unsafe practices.

NOTICE:Indicates a situation that could result in equipment or property-damage-only

accidents.

RT-SVX23E-EN 3

Warnings, Cautions and Notices

WARNING

Personal Protective Equipment (PPE) Required!

Installing/servicing this unit could result in exposure to electrical, mechanical and chemical

hazards.

• Before installing/servicing this unit, technicians MUST put on all Personal Protective

Equipment (PPE) recommended for the work being undertaken. ALWAYS refer to appropriate

MSDS sheets and OSHA guidelines for proper PPE.

• When working with or around hazardous chemicals, ALWAYS refer to the appropriate MSDS

sheets and OSHA guidelines for information on allowable personal exposure levels, proper

respiratory protection and handling recommendations.

• If there is a risk of arc or flash, technicians MUST put on all necessary Personal Protective

Equipment (PPE) in accordance with NFPA70E for arc/flash protection PRIOR to servicing the

unit.

Failure to follow recommendations could result in death or serious injury.

WARNING

Contains Refrigerant under Pressure!

System contains oil and refrigerant under high pressure. Recover refrigerant to relieve pressure

before opening the system. See unit nameplate for refrigerant type. Do not use non-approved

refrigerants, refrigerant substitutes, or refrigerant additives. Failure to follow proper procedures

or the use of non-approved refrigerants, refrigerant substitutes, or refrigerant additives could

result in death or serious injury or equipment damage.

WARNING

R-410A Refrigerant under Higher Pressure than R-22!

The units described in this manual use R-410A refrigerant which operate at higher pressures

than R-22 refrigerant. Use ONLY R-410A rated service equipment or components with this unit.

For specific handling concerns with R-410A, please contact your local Trane representative.

Failure to use R-410A rated service equipment or components could result in equipment

exploding under R-410A high pressures which could result in death, serious injury, or equipment

damage.

WARNING

Harmful Ultraviolet (UV) Lights!

Do not field install ultraviolet lights in the manufacturer air handling equipment for the intended

purpose of improving indoor air quality. High intensity C-band ultraviolet light is known to

severely damage polymer (plastic) materials and poses a personal safety risk to anyone exposed

to the light without proper personal protective equipment (can cause damage to eyes and skin).

Polymer materials commonly found in HVAC equipment that may be susceptible include

insulation on electrical wiring, fan belts, thermal insulation, various fasteners and bushings.

Degradation of these materials could result in serious damage to the equipment. Failure to

follow this recommendation could result in death or serious injury and equipment damage. The

manufacturer accepts no responsibility for the performance or operation of our air handling

equipment in which ultraviolet devices were installed outside of the manufacturer’s factory.

NOTICE

Roof Damage!

System contains oil and refrigerant under high pressure. Roofs should be protected from

exposure to oils and refrigerant in the system. If rooftop is not protected damage to the roof may

occur.

4RT-SVX23E-EN

Table of Contents

Overview of Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Model Number Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

General Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unit Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Compressor Nameplate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Unit Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Economizer Control Actuator (Optional) ReliaTel™ Control . . . . . . . . . . . 8

RTCI -- ReliaTel™ Trane Communication Interface (Optional) . . . . . . . . . 8

RLCI - ReliaTel™ LonTalk Communication Interface (Optional) . . . . . . . . 8

RTOM – ReliaTel™ Options Module (Optional) . . . . . . . . . . . . . . . . . . . . . 9

System Input Devices & Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Pre-Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Unit Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Unit Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Unit Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Foundation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Ductwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Roof Curb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Rigging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Factory Installed Economizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Temperature Limit Switch Usage for Electric Heat Units . . . . . . . . . . . . 30

Horizontal Discharge Conversion WSC036E, WSC048E . . . . . . . . . . . . . 30

Horizontal Discharge Conversion WSC060-120E . . . . . . . . . . . . . . . . . . . 31

TCO-A Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Return Air Smoke Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Main Electrical Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Electric Heat Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Low Voltage Wiring (AC & DC) Requirements . . . . . . . . . . . . . . . . . . . . . 36

Condensate Drain Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Filter Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Field Installed Power Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Main Unit Power Standard Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Main Unit Power Optional TBUE Wiring (Through the Base Electrical Op-

tion) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Field Installed Control Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Smoke Detector - (ReliaTel™ only) Customer Low Voltage Wiring- . . . . 44

Pre-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Space Temperature Averaging (ReliaTel™ only) . . . . . . . . . . . . . . . . . . . 45

Voltage Imbalance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Electrical Phasing (Three Phase Motors) . . . . . . . . . . . . . . . . . . . . . . . . . . 48

RT-SVX23E-EN 5

Table of Contents

Compressor Crankcase Heaters (Optional on WSC036E*, WSC048E1, and

& WSC060E1 - Standard on remaining units) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Test Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

ReliaTel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Verifying Proper Air Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Units with 5-Tap Direct Drive Indoor Fan . . . . . . . . . . . . . . . . . . . . . . . . . 51

Units with Belt Drive Indoor Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Units with Direct Drive Indoor Fan with MMC . . . . . . . . . . . . . . . . . . . . . 53

Return Air Smoke Detector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Economizer Start-Up ReliaTel Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Compressor Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Heating Start-Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Final System Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Fan Belt Adjustment - Belt Drive Units . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Monthly Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Return Air Smoke Detector Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 58

Cooling Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Heating Season . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Coil Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Final Process . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Trouble Shooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Method 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Method 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Resetting Cooling and Heating Lockouts . . . . . . . . . . . . . . . . . . . . . . . . . 64

Zone Temperature Sensor (ZTS) Test . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Programmable & Digital Zone Sensor Test . . . . . . . . . . . . . . . . . . . . . . . 66

Unit Economizer Control (ECA) Troubleshooting ReliaTel Control . . . . . 67

Troubleshooting procedures for Direct Drive Plenum Fan . . . . . . . . . . . 68

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Heat Pump WCC, WCD, WCH, WCM and WSC (Parts Only) . . . . . . . . . . 70

Heat Pump WCZ, WCY, WCX, WCC, WCD, WCH, WCM, WCP and WSC

(Parts Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

6RT-SVX23E-EN

Model Number Descriptions

Digit 1 - Unit Type

W Packaged Heat Pump3

Digit 2 - Efficiency

S Standard Efficiency

Digit 3 - Airflow

C Convertible

Digit 4,5,6 - Nominal Gross

Cooling Capacity (MBh)

036 3 Tons

048 4 Tons

060 5 Tons

072 6 Ton

090 7½ Ton, Single Compressor

120 10 Ton

Digit 7 - Major Design Sequence

E R-410A Refrigerant

Digit 8 - Voltage Selection

1 208/230/60/1

3 208-230/60/3

4 460/60/3

W 575/60/3

Digit 9 - Unit Controls

R ReliaTel™ Microprocessor

Digit 10 - Heating Capacity

Digit 11 - Minor Design Sequence

A First Sequence

Digit 12,13 - Service Sequence

** Factory Assigned

0=No Electric Heat F=14 kW (1 phase)1

A=5 kW (1 phase)1G=18 kW (1&3 phase)

B=6 kW (3 phase) J=23 kW (3 phase)

C=9 kW (3 phase) K= 27 kW (3 phase)

D=10 kW (1 phase)1N = 36 kW (3 phase)

E=12 kW (3 phase) P = 54 kW (3 phase)

Digit 14 - Fresh Air Selection

0NoFreshAir

A Manual Outside Air Damper 0-50%2

B Motorized Outside Air Damper

0-50%

C Economizer, Dry Bulb 0-100%

without Barometric Relief5

D Economizer, Dry Bulb 0-100%

with Barometric Relief5

E Economizer, Reference Enthalpy

0-100% without Barometric Relief5

F Economizer, Reference Enthalpy

0-100% with Barometric Relief5

G Economizer, Comparative

Enthalpy 0-100% without

Barometric Relief5

H Economizer, Comparative

Enthalpy 0-100% with Barometric

Relief5

Digit 15 - Supply Fan/Drive Type/

Motor

0 Standard Drive4

1 Oversized Motor

2 Optional Belt Drive Motor

Digit 16 - Hinged Service Access/

Filters

0 Standard Panels/Standard Filters

A Hinged Access Panels/Standard

Filters

B Standard Panels/2” MERV 7 Filters

C Hinged Access Panels/2” MERV 7

Filters

D Standard Panels/2” MERV 13 Filters

E Hinged Access Panels/2” MERV 13

Filters

Digit 17 - Condenser Coil

Protection

0 Standard Coil

1 Standard Coil with Hail Guard

2 Black Epoxy Pre-Coated Condenser

Coil

3 Black Epoxy Pre-Coated

Condenser Coil with Hail Guard

4 CompleteCoat™ Condenser Coil

5 CompleteCoat™ Condenser Coil

with Hail Guard

Digit 18 - Through the Base

Provisions

0 No Through the Base Provisions

A Through the Base Electric6

Digit 19 - Disconnect/Circuit

Breaker (three-phase only)

0 No Disconnect/No Circuit Breaker

1 Unit Mounted Non-Fused

Disconnect6

2 Unit Mounted Circuit Breaker6

Digit 20 - Convenience Outlet

0 No Convenience Outlet

A Unpowered Convenience Outlet

B Powered Convenience Outlet

(three-phase only)7

Digit 21 - Communications

Options

0 No Communications Interface

1TCI

2LCI

Digit 22 - Refrigeration System

Option

0 Standard Refrigeration System8

Digit 23 - Refrigeration Controls

0 No Refrigeration Control3

1Frostat

2CrankcaseHeater

3 Frostat and Crankcase Heater11

Digit 24 - Smoke Detector

0 No Smoke Detector

A Return Air Smoke Detector9

B Supply Air Smoke Detector

C Supply and Return Air Smoke

Detectors9

Digit 25 - Monitoring Controls

0 No Monitoring Control

1 Clogged Filter Switch

2 Fan Failure Switch

3 Discharge Air Sensing Tube

4 Clogged Filter Switch and Fan

Fail Switch

5 Clogged Filter Switch and Discharge

Air Sensing Tube

6 Fan Fail Switch and Discharge Air

Sensing Tube

7 Clogged Filter and Fan Fail Switches

and Discharge Air Sensing Tube

RT-SVX23E-EN 7

Model Number Descriptions

Model Number Notes

1. Available on 3-5 Ton Models.

2. Manual outside air damper will

ship factory supplied within the

unit, but must be field installed.

3. High pressure control is standard

on all units.

4. Multispeed direct drive standard

on single-phase products. Belt

drive standard on three-phase 3-

7½ ton. Variable speed direct drive

standard on 10 ton.

5. Economizer with Barometric

Relief is for downflow configured

units only. Order Economizer

without Barometric Relief for

horizontal configuration.

Barometric Relief for horizontal

configured units must be ordered

as field installed accessory.

6. Through the base electric required

when ordering disconnect/circuit

breaker options.

7. Requires use of Disconnect or

Circuit Breaker.

8. Standard metering devices are

TXVs.

9. The return air smoke detector may

not fit up or work properly on the

units when used in conjunction

with 3rd party accessories such as

bolt on heat wheels, economizers

and power exhaust. Do not order

the return air smoke detectors

when using this type of accessory.

10. Requires hinged access panels.

11. Crankcase heaters are only

available as option on WSC036E,

WSC048E1, & WSC060E1. CCH are

standard on all other units.

8RT-SVX23E-EN

General Information

Unit Nameplate

A Mylar unit nameplate is located on the unit’s corner support next to the filter access panel. It

includes the unit model number, serial number, electrical characteristics, refrigerant charge, as well

as other pertinent unit data.

Compressor Nameplate

The nameplate for the compressors are located on the side of the compressor.

Unit Description

Before shipment, each unit is leak tested, dehydrated, charged with refrigerant and compressor oil,

and run tested for proper control operation.

The condenser coils are aluminum fin, mechanically bonded to copper tubing.

Direct-drive, vertical discharge condenser fans are provided with built-in thermal overload

protection.

The ReliaTel™ Control Module is a microelectronic control system that is referred to as

“Refrigeration Module” (RTRM). The acronym RTRM is used extensively throughout this

document when referring to the control system network.

These modules through Proportional/Integral control algorithms perform specific unit functions

that governs unit operation in response to; zone temperature, supply air temperature, and/or

humidity conditions depending on the application. The stages of capacity control for these units

is achieved by starting and stopping the compressors.

The RTRM is mounted in the control panel and is factory wired to the respective internal

components. The RTRM receives and interpret information from other unit modules, sensors,

remote panels, and customer binary contacts to satisfy the applicable request for cooling.

Economizer Control Actuator (Optional) ReliaTel™ Control

The ECA monitors the mixed air temperature, return air temperature, minimum position setpoint

(local or remote), power exhaust setpoint, CO2 setpoint, CO2, and ambient dry bulb/enthalpy

sensor or comparative humidity (return air humidity against ambient humidity) sensors, if

selected, to control dampers to an accuracy of +/- 5% of stroke. The actuator is spring returned to

the closed position any time that power is lost to the unit. It is capable of delivering up to 25 inch

pounds of torque and is powered by 24 VAC.

RTCI -- ReliaTel™ Trane Communication Interface (Optional)

This module is used when the application calls for an ICSTM building management type control

system. It allows the control and monitoring of the system through an ICS panel. The module can

be ordered from the factory or ordered as a kit to be field installed. Follow the installation

instruction that ships with each kit when field installation is necessary.

RLCI - ReliaTel™ LonTalk Communication Interface (Optional)

This module is used when the application calls for an ICSTM building management type control

system that is LonTalk. It allows the control and monitoring of the system through an ICS panel.

The module can be ordered from the factory or ordered as a kit to be field installed. Follow the

installation instruction that ships with each kit when field installation is necessary.

RT-SVX23E-EN 9

General Information

RTOM – ReliaTel™ Options Module (Optional)

The RTOM monitors the supply fan proving, clogged filter, supply air temperature, exhaust fan

setpoint, supply air tempering, Frostat™ and smoke detector. Refer to system input devices and

functions for operation.

System Input Devices & Functions

The RTRM must have a zone sensor or thermostat input in order to operate the rooftop unit. The

flexibility of having several mode capabilities depends upon the type of zone sensor thermostat

selected to interface with the RTRM.

The descriptions of the following basic Input Devices used within the RTRM network are to acquaint

the operator with their function as they interface with the various modules. Refer to the unit’s

electrical schematic for the specific module connections.

The following controls are available from the factory for field installation.

Supply Fan Failure Input (Optional)

The Fan Failure Switch can be connected to sense indoor fan operation:

FFS (Fan Failure Switch) If air flow through the unit is not proven by the differential pressure switch

connected to the RTRM (factory set point 0.07 “w.c.) within 40 seconds nominally, the RTRM will

shut off all mechanical operations, lock the system out, send a diagnostic to ICS, and the SERVICE

output will flash. The system will remain locked out until a reset is initiated either manually or

through ICS.

Clogged Filter Switch (Optional)

The unit mounted clogged filter switch monitors the pressure differential across the return air

filters. It is mounted in the filter section and is connected to the RTOM. A diagnostic SERVICE signal

is sent to the remote panel if the pressure differential across the filters is at least 0.5" w.c. The

contacts will automatically open when the pressure differential across the filters decreases to

approximately 0.4" w.c. The clogged filter output is energized when the supply fan is operating and

the clogged filter switch has been closed for at least 2 minutes. The system will continue to operate

regardless of the status of the filter switch.

Note: On units equipped with factory installed MERV 13 filters, a clogged filter switch with

different pressure settings will be installed. This switch will close when the differential

pressure is approximately 0.8' w.c. and open when the differential falls to 0.7" w.c.

Compressor Disable (CPR1/2)

This input incorporates the low pressure control (LPC) of each refrigeration circuit and can be

activated by opening a field supplied contact installed on the LTB.

If this circuit is open before the compressor is started, the compressor will not be allowed to

operate. Anytime this circuit is opened for 1 continuous second during compressor operation, the

compressor for that circuit is immediately turned “Off”. The compressor will not be allowed to

restart for a minimum of 3 minutes should the contacts close.

If four consecutive open conditions occur during the first three minutes of operation, the

compressor for that circuit will be locked out, a diagnostic communicated to the remote panel (if

installed), and a manual reset will be required to restart the compressor.

Low Pressure Control

When the LPC is opened for 1 continuous second, the compressor for that circuit is turned off

immediately. The compressor will not be allowed to restart for a minimum of 3 minutes.

If four consecutive open conditions occur during an active call for cooling, the compressor will be

locked out, a diagnostic communicated to ICS™, if applicable, and a manual reset required to

10 RT-SVX23E-EN

General Information

restart the compressor. On dual compressor units only the affected compressor circuit is locked

out.

High Pressure Control

The high pressure controls are wired in series between the compressor outputs on the RTRM and

the compressor contactor coils. If the high pressure control switch opens, the RTRM senses a lack

of current while calling for cooling and locks the compressor out.

If four consecutive open conditions occur during an active call for cooling, the compressor will be

locked out, a diagnostic communicated to ICS™, if applicable, and a manual reset required to

restart the compressor. On dual compressor units only the affected compressor circuit is locked

out.

Power Exhaust Control (Optional)

The power exhaust fan is started whenever the position of the economizer dampers meets or

exceed the power exhaust setpoint when the indoor fan is on.

The setpoint panel is located in the return air section and is factory set at 25%.

Lead/Lag Control (Dual Circuit Only)

Lead/Lag is a selectable input located on the RTRM. The RTRM is configured from the factory with

the Lead/Lag control disabled. To activate the Lead/Lag function, simply cut the wire connected to

J3-8 at the RTRM. When it is activated, each time the designated lead compressor is shut off due

to the load being satisfied, the lead compressor or refrigeration circuit switches. When the RTRM

is powered up, i.e. after a power failure, the control will default to the number one circuit

compressor.

Zone Sensor Module (ZSM) (BAYSENS107*)

This electronic sensor features three system switch settings (Heat, Cool, and Off) and two fan

settings (On and Auto). It is a manual changeover control with single setpoint. (Cooling Setpoint

Only)

Zone Sensor Module (ZSM) (BAYSENS109*)

This electronic sensor features four system switch settings (Heat, Cool, Auto, and Off) and two fan

settings (On and Auto). It is a manual or auto changeover control with dual setpoint capability. It

can be used with a remote zone temperature sensor BAYSENS077*.

Programmable Zone Sensor - BAYSENS119*

This 7 day programmable sensor features 2, 3 or 4 periods for Occupied or Unoccupied

programming per day. If the power is interrupted, the program is retained in permanent memory.

If power is off for an extended period of time, only the clock and day may have to be reset.

The Zone Sensor allows selection of 2, 3 or 4 system modes (Heat, Cool, Auto, and Off), two fan

modes (On and Auto). It has dual temperature selection with programmable start time capability.

The occupied cooling set point ranges between 45 and 98 degrees Fahrenheit. The heating set point

ranges between 43 and 96 degrees Fahrenheit.

A liquid crystal display (LCD) displays zone temperature, temperature set points, day of the week,

time, and operational mode symbols.

The Option Menu is used to enable or disable applicable functions, i.e.; Morning Warm-up,

Economizer minimum position override during unoccupied status, Fahrenheit or Centigrade,

Supply air tempering, Remote zone temperature sensor, 12/24 hour time display, Smart fan, and

Computed recovery.

During an occupied period, an auxiliary relay rated for 1.25 amps @ 30 volts AC with one set of

single pole double throw contacts is activated. Electronic Timeclock (BAYCLCK001A).

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Bomba de calor de Trane

Trane

Trane A4HP4017A1000B Instrucciones de montaje

Trane

Trane 4TWR6 Manual de usuario

Trane

Trane A4AC4018B1000B Instrucciones de montaje

Trane

Trane A4AC3018A1000A Instrucciones de montaje

Trane

Trane 4TWR3 Instrucciones de montaje

Trane

Trane A4AC5018D1000A Manual de usuario

Trane

Trane 4WCZ6036B3000A Manual de usuario

Trane

Trane UH-PRC001-EN Hoja de datos

Trane

Trane Horizon OAKD Instrucciones de instalación y funcionamiento

Trane

Trane EXWA Manual de usuario

Trane

Trane 4MXW6 Manual de usuario

Trane

Trane 4TWR4 Instrucciones de instalación

Trane

Trane TVR 5G Manual de usuario

Trane

Trane 2TTR2018-060 Instrucciones de montaje

Trane

Trane 13.4 SEER2 J4PH4 Series Manual de usuario

Trane

Trane 22-5213-WEB01 Manual de usuario

Trane

Trane XR13 Manual de usuario

Trane

Trane 2TTA2 Series Instrucciones de montaje

Trane

Trane Weathertron 22-5202-03-3605 Instrucciones de instalación

Trane

Trane WCH024C1 Manual del propietario

Trane

Trane WEATHERTRON 4TWX6 Instrucciones de montaje

Trane

Trane 2GN Series Instrucciones de montaje

Trane

Trane A4AC4018B1000A Instrucciones de montaje

Trane

Trane Precedent WSC Manual de usuario

Manuales populares de Bomba de calor de otras marcas

MICROWELL

MICROWELL HP 1000 GREEN Manual de usuario

Sanyo

Sanyo SAP120FCH Manual de usuario

Daikin

Daikin EHYHBH05AA Manual de usuario

Panasonic

Panasonic WH-SDF03E3E5 Guía

Bryant

Bryant 544B Manual de usuario

Airxcel

Airxcel 45000 Series Manual

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Manual de usuario

Dimplex

Dimplex LI 16I-TUR Guía del usuario

Carrier

Carrier WSHP Open v3 Guía de configuración rápida

TGM

TGM CTV14CN018A Manual de usuario

Carrier

Carrier 38MGQ Series Manual de usuario

Kokido

Kokido K2O K880BX/EU Guía de solución de problemas

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Guía rápida

Carrier

Carrier 48EZN Manual de usuario

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Instrucciones de funcionamiento

Ariston

Ariston NIMBUS Manual de usuario

Weishaupt

Weishaupt WWP L 7 Guía del usuario

GE Zoneline AZ85H09EAC Manual de usuario