TrackNet TABS TBDW100-915 Manual de usuario
Door & Window Sensor
TBDW100-915
TBDW100-868
Reference Manual
1
© 2017 TrackNet Inc, USA and Trackio GmbH, Switzerland. All rights reserved.
Table of Contents
1. Description ................................................1
2. Specifications...........................................2
2.1 Mechanical.........................................2
2.1.1 Sensor ............................................. 2
2.1.2 Magnet........................................... 2
3. Operation..................................................3
3.1 Power On Reset ...............................3
3.2 Transport Mode ..............................3
3.3 Installation Mode ............................3
3.4 Default Operation............................3
4. Messages..................................................4
4.1 Status..................................................4
4.1.1 Common Fields............................. 4
4.1.2 Triggers.......................................... 4
4.1.3 Payload .......................................... 4
4.2 Command .........................................5
1. Description
The Tabs Door & Window sensor utilizes
LoRaWAN connectivity to communicate the
proximity or not of a magnet. The intended
use is to place the sensor and magnet on
separate elements of a door or window to
determine if the door or window is open or
closed.
The sensor is composed of two parts. The
main body contains the active electronics to
measure magnetic fields and transmit any
changes to a LoRaWAN network. The second
part is a permanent magnet of sucient field
strength to be detected by the Hall Eect
sensor on the main body.
2
© 2017 TrackNet Inc, USA and Trackio GmbH, Switzerland. All rights reserved.
2. Specifications
2.1 Mechanical
2.1.1 Sensor
Length x Width x Height 50mm x 20mm x 50mm
Weight 30g without battery
40g with battery
2.1.2 Magnet
Length x Width x Height 31mm x 20mm x 20mm
Weight 12g
2.2 Environmental
Temperature -20°C to +50°C
IP Rating IP 50 equivalent
2.3 Radio
Frequency
Either 863–870MHz for EU
models and 902–928MHz for
North America
Tx Power +19dBm conducted
Rx Sensitivity
(Conducted) -140dBm
Antenna Gain -2dBi Peak, -5dBi Avg
2.5 Power
Source 3.6V ½ AA Li-SOCl2 1200mAh
battery
Maximum Voltage 3.6V
Minimum Voltage 3.1V
Current 135mA maximum/5uA
minimum
2.6 User Interface
LEDs One blue LED
Sensor Hall Eect 14 Gauss trigger
typical
2.4 Certifications and Conformity
FCC ID: 2AMUGTBSP100
IC: 22980-TBSP100
CE
ROHS REACH
2.7 Additional Features
PCB Temperature
Battery Monitoring
3
© 2017 TrackNet Inc, USA and Trackio GmbH, Switzerland. All rights reserved.
3. Operation
3.1 Power On Reset
Anytime the device power drops below 2.8V the device will enter a Power
On Reset (POR) when greater than 2.8V is restored. After a POR the device
will wait up to 30 seconds before entering default operation.
3.2 Transport Mode
They are shipped with a plastic battery isolation tab that must be removed
to enable operation.
3.3 Installation Mode
The device shall enter installation mode after being commanded by the
network and remain in installation mode for 3 minutes. While in installation
mode the device will flash the LED 3 times within 500ms for every transition
between sensing states, i.e. whenever the device detects changes between
open and closed.
3.4 Default Operation
While in default operation the device will immediately send a message any
time there is a transition from Open to Close or vice-versa. Additionally, the
device will send a message anytime it has been inactive for 6 hours.
4
© 2017 TrackNet Inc, USA and Trackio GmbH, Switzerland. All rights reserved.
4. Messages
LoRaWAN Packets for this device use port 100.
4.1 Status
4.1.1 Common Fields
Status[7:0]
{Fault3, Fault2, LED1, LED0, Fault1, Fault0, BTN1, BTN0}
• Nominally Fault0 indicates no network time available
• Nominally Fault1 indicates loss of primary sensor function
• Nominally Fault2 indicates loss of secondary sensor function
• Nominally Fault3 indicates loss of network connectivity
Battery[7:0]
LoRaWAN Decode
• 0 => Device is charging or line powered
• 1 to 254 => device level, 1 = minimum and 254 = fully charged
• Futher encode
• [7:4] = predicted battery life percentage, 15 = New, 0 = Replace
• [3:0] = BatteryVoltage — 2.5V, in 0.1V steps, So 3.1V = 6
• 255 => Device could not measure battery — possible Fault
Temperature[6:0]
Unsigned Integer (0 to 127) Temperature = value - 32, measurement range -32° to 95°C
4.1.2 Triggers
Packet Triggers: 360 minute inactivity, Switch Open, Switch Close
4.1.3 Payload
Port 100
Payload Length 8 bytes
Byte 0 1 2 3 4 5 6 7
Field Status Battery Temp Time Count
5
© 2017 TrackNet Inc, USA and Trackio GmbH, Switzerland. All rights reserved.
Status
Sensor status
Bit [0] 1 – open, 0 – closed
Bits [7:1] RFU
Battery
Battery level
Bits [3:0] unsigned value ν, range 1 – 14;
battery voltage in V = (25 + ν) ÷ 10.
Bits [7:4] unsigned value κ, range 0 – 15;
remaining battery capacity in % = 100 × (κ÷ 15).
Temp
Temperature as measured by on-board NTC
Bits [6:0] unsigned value τ, range 0 – 127;
temperature in °C = τ- 32.
Bit [7] RFU
Time Time elapsed since last event trigger
Bits [15:0] unsigned value in minutes, range 0 – 65,535.
Count
Total count of event triggers
Bits [23:0] unsigned value, range 0 – 16,777,215.
Note: This value is not stored persistently on the device, and may reset whenever the device is power-cycled or rebooted.
4.2 Command
4.1.3 Payload (cont.)
RESERVED.
Este manual sirve para los siguientes modelos
1
Tabla de contenidos
