NO Part Name Q’ty
5
6
7
2
1
1
1
8
1
9
Valve screw
AA battery
Quick installation guide
Product warranty card
Velcro
NO Part Name Q’ty
1
2
3
3
1
1
4
4
Sensor
Valve package (valve and screw)
Tire pressure monitoring receiver
Valve
VS-63W008 Contents
FCC Regulations
This tire pressure monitoring system has complied with Article 15 of the FCC regulatory requirements of the USA,
but it is still needed to pay attention to the following two items:
(1) Other harmful interferences may affect the system’s normal operation.
(2) Abnormal operation may cause the system to fail.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End
users must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
Note: The product will not be guaranteed if user change or modify the hardware and system design.
Warning
Product Warning
1.Do not operate a TPMS receiver while driving. The company is exempt from all consequences because of
driver’s careless and improper operation.
2.The system adopts the wireless transmissi of signals. In some special circumstances, interference or erroneous
methods of operation or installation method errors may cause weaker signal or its inability to receive signals. If
the insulation adhesive sticker of the windshield contains metal material, it will be likely to affect reception
conditions. If the tire pressure and temperature readings on the TPMS receiver are displayed as ---, this
condition represents the receiver cannot receive signals emitted by the sensors. Drive the vehicle away from
the current location (nearby there may be signal interference) or drive the vehicle to a tire shop to check, or
return the TPMS receiver to distributor for repair. If the battery status of the TPMS sensors inside the tire is low
(because abnormal conditions continue to occur, the battery may make the TPMS sensors continuously emit
signals to warn the driver, so that battery life is shorter than the normal life), please go as soon as possible to
the specified service stations to confirm whether the TPMS Sensors need to be replaced.
3.Please change the Receiver’s dry battery or sensor while the Receiver’s dry battery power is low or Sensor Low
battery warning is alarm, or it may cause the TPMS thus cannot be operated and alarm normally. You will take
all risks and responsibilities for this!
4.Temporary resealing or re-inflation products containing internal sealants or propellants in any tire assembly may
adversely affect the operation of the sensor/transmitter. The product manufacturer does not assume any liability
as a result of these.
Important Safety Guide
System Warning
When the system displays a warning light and warning "beeps", you should immediately slow down, stop in a safe location and check the
tire condition, and immediately drive to the nearest qualified tire maintenance garage to repair and make related in-depth examination.
Function key Normal mode Setting mode
+
Backlighting and enter the function
setting mode (hold for 3 seconds) Leave function setting mode
Mute the warning audio Save the setting
Up and down selection/
value adjustment
Rotation display setting Unit setting or right button
Set the backlight to be always on/off
(Fig 1) Loosen the tire. Fix both sides of the tire and press, and make it bulge.
(Fig 2) Remove the tire. The valve faces the mounting arm in the one o’clock direction, remove the tire.
(Fig 3) Remove the sensor. Loosen the fixing screw, allow the sensor separate from the valve, and release the nut to take it apart from
the valve.
(Fig 4) Install the sensor and valve. Insert the valve through the rim hole, fix the screw to secure the valve and sensor by 2 Nm in torque,
attach the sensor body to the inner surface of the rim by adjusting the angle of the sensor body.
(Fig 5/6) Install valve to the rim hole. Guide the washer into the valve, and fix the nut by 4 Nm in torque, then tighten the cap.
Note: Mount the tire. Grip the rim edge, and the valve is opposite to the mounting arm, avoid hitting the sensor during arm operation.
2.2 Sensor Assembly Process
Please follow the label on the sensor, install the sensor into the rims accordingly, it could skip the “ID Learning” steps for each sensor!
2.1 Installation Location
1.Product Parts List
2.Sensor Installation
3.2 Warning Light Symbol
Abnormal Warning Illustration
When the TPMS sensor transmits abnormal
signal to the receiver, a warning symbol will
blink and “beep” as an audio alarm. The
abnormal value is shown on the corresponding
tire on the receiver.
It’s our recommendation to mount within 1/3 of the region right on the center of dashboard, or the position
which can receive the sensor signal well.
Note:
1.Recommended battery type: Alkaline E91, 1.5V, AA battery, The operating temperature of regular alkaline
battery is -18℃~55℃, higher temperatures will cause battery leakage.
2.Power saving design: in order to decrease the consumption of receiver battery, the receiver has a dormant
design, to save the battery power consumption. When the ignition is on, the receiver will be restarted
automatically by shock.
3.If you finish setting and want to return back to tire pressure/tire temperature display screen under any
setting mode, please hold the button for about 3 seconds
3.3 Recommend the Receiver Mounting Position
4.Setting Items
3.1 Buttons Function Introduction
3.Installation of Tire Pressure Monitoring Receiver
Note: For the standard tire pressure value, please refer to the placard which be attached to the side of the driver seat.
●Warning of excessive low tire pressure indicates tire pressure has been leaked to 20% or less of the standard tire pressure value
set by the user, or ≦150 kPa (22psi).
●Warning of excessive high tire pressure indicates tire pressure has been risen to 50% or more of the standard tire pressure value
set by the user.
●Warning of excessive high tire temperature indicates tire air temperature is higher than the user setting value of the warning tire air
temperature.
●For example, if the standard tire pressure value is 31 psi, when tire pressure is increased ≧46.5psi or decreased ≦24.8psi, the
receiver will alarm.
●For example, if the warning temperature is 80℃, when tire temperature is increased ≧80℃, the receiver will alarm.
●If the environment temperature is too hot or cold, the tire pressure will vary accordingly. Please go to the tire shop to inflate or deflate
the tires to prevent an erroneous alarm.
Hold for 3~5 seconds to enter the “SETTINGS”mode. Press and set the standard tire pressure value,
the value of the front wheel will blink, press the button to adjust the value. Press one more time to switch
to front wheel temperature setting, press the button to adjust the value. The value is fixed and will stop
blinking after pressing , then press for the rear wheel, and repeat the procedure.
4.1 Tire Pressure Standard and Temperature Warning Value Setting
▲ Rear wheel tire pressure and temperature value setting▲ Front wheel tire pressure and temperature value setting
4.2 ID LEARNING Setting
▲ ID LEARNING setting
Note:
1.When learning the sensor IDs by pressure deflation, please
proceed with fast deflation to avoid unsuccessful ID learning.
4.3 Tire Position Rotation Setting
4.4 Spare Tire Setting
▲ Rear wheel tire pressure and temperature setting
4.5 Tire pressure and tire temperature unit setting
▲ Tire pressure and temperature unit setting
Function Description
SETTINGS Tire pressure and temperature setting for front and rear tire (4.1)
LEARNING TPMS sensor ID learning (4.2)
ROTATION Tire position rotation (4.3)
SPARE TIRE Spare tire off or on (4.4)
Unit Tire pressure and tire temperature unit setting (4.5)
System Installation
The wireless TPMS needs to be installed by qualified personnel in accordance with installation manual to enjoy related warranty. If improper
assemble or disassemble process damages the sensor, it will not be covered by warranty.
Reminder: annual periodic inspection for the "sensor valve" is proposed, which should be replaced immediately if damaged, in order to avoid
air leakage.
k
k
When the wheel is switched, the sensor position would be different
from original. You should use RORATION mode for tire position
setting.
In ROTATION mode, 1 to 4 digits is showed on screen. Press ,
then the digit will flash. Press to adjust tire position. Press to
save when the setting is completed.
Enter “Unit” setting mode, press once for tire pressure unit, the
unit will blink, press to choose the desired unit, press to
complete the unit setting. Then press for temperature unit, follow
the previous procedure to complete the setting.
If it is necessary for the spare tire to install a TPMS sensor, the
receiver could display the spare tire pressure and temperature, it
can be set in the SPARE TIRE mode.
It shows the spare tire position when using the Spare Tire setting.
Tap button and the digit would be flashing. Tap button to
select ON or OFF and confirm whether you need to activate spare
tire display mode. After setting is completed, tap button to save
the setting.
~Outside of the rim 1.Screw
2.Sensor
3.Rubber washer
4.Valve core
5.Washer
6.Washer
7.Nut
8.Valve cap
~Inside of the rim
Fig 1 Fig 2 Fig 3
Fig 4 Fig 5 Fig 6
Light SymbolNo. Abnormal Light Message
Alarm for excessive high tire temperature
Warning for low battery in TPMS sensor,
need to replace new sensor
Warning for low battery in receiver,
need to replace new battery
Alarm for excessive high/low tire pressure
▲
ROTATION setting
Hold for 3~5 seconds to enter the setting mode, press for the following functions:
When replacing or installing a tire pressure monitoring sensor for
a second time, the receiver must learn the new tire pressure
sensor ID. The setting procedure is below:
4.2.1 Hold the button for 3 to 5 seconds, enter the
“SETTINGS” mode.
4.2.2 Press twice to enter the “LEARNING” mode.
4.2.3 Press the button, the digits will blink.
4.2.4 Deflate the tire, the receiver will beep when receiving the
signal; the ID learn setting is finished when the digits stops
blinking.
4.2.5 Press the button again, then do the learning procedure
for the next tire.
4.2.6 Repeat the above procedures until completing the learning
of the 4 tires, then please press the button to save the
ID numbers.
Quick Installation Guide
Battery TPMS System
FCC Regulations
FCC RF Radiation Exposure Statement
Product Warning
System Installation
Important Safety Guide
1.Product Parts List
2.Sensor Installation
2.2 Sensor Assembly Process
2.1 Installation Location
3.Installation of Tire Pressure Monitoring Receiver
4.Setting Items
4.1 Tire Pressure Standard and Temperature Warning
Value Setting
4.2 ID LEARNING Setting
4.3 Tire Position Rotation Setting
4.4 Spare Tire Setting
4.5 Tire pressure and tire temperature unit setting
3.3 Recommend the Receiver Mounting Position
3.2 Warning Light Symbol
3.1 Buttons Function Introduction
SETTINGS
SETTINGS
SETTINGS
