TOZO Q1012 Manual de usuario
Dear respectable customers,
Thank you very much for your purchase of aircraft products
manufactured by TOZO company! The built-in barometer in the
aircraft can accurately hover on the xed height, in order to you can
be safe and correct use of this product, be sure to carefully read this
specication, and to retain the convenience for future reference!
Q1012
www.tozostore.com
Note:
1.The motors , circuit board and battery may heat up with use. Take 10-minutes cool-down
between flights and recharge to ensure your parts last as lond as possible.
2.When out of control, just press both L2 and R2 button for emergency stop to prevent
more damage.
3. No need TF card for Q1012. The photos and video will be stored on the phone through APP (scan
the QR code on manual page 13).
1
Unfold the aircraft
1. When you receive the aircraft, the state of being
acquiescent is the folding state, at this time
unfold the aircraft arms respectively rotate to
outside about 120 degrees ( as shown in Figure 2),
when you hear a sound of click, the rotation has
been in place.
12
3 4
Note: when rotate in place stop the lateral rotation,
or else this will damage the built-in
rotational-axle structure in the aircraft arms.
2. After unfold the four arms and then unfold the
foot frames according to the shown style in
Figure 4.
2
Know your aircraft
●When ying, please take the aircraft head toward to
the front, so that you will be better to control the
aircraft.
●The central axis location of the blade are marked
"A" "B" blades, when the blade is damaged, please
follow the above shown picture to replace the blade,
when changing please note that two blades of the
same machine arm need to be replaced the same
numbers, such as "B1", on both sides of the blades
are required "B1", if "B2", is required "B2", so the
aircraft will be more stably ight.
Know your remote control
A Blade
A BladeB Blade
B Blade
Front
Battery cabin
power switch
3
TIP: Camera key and Recording key may not have function on some
of the ying models.
Flight notes
1.This product is suitable for the people who with
operating experience of model , and at least 14 years
old.
2.When using this product, please choose the wider
space, away from the barrier, crowd, high voltage
wires, communication base station and so on.
3.Do not use this product in bad weather conditions,
such as strong wind (wind speed 3 classes or more)
or thunderstorms, heavy fog weather and so on.
4.When the aircraft in ight, please keep a certain
distance from it, avoid ngers or body close to the
propeller so as not to cause harm.
Accelerator/Left and
right rotatory rocker
Left rotation ne tunning
power switch
Right rotation
ne tuning
Left y
ne tunning
LCD display
Front rear left
and right rocker
Advance ne tuning
Right y ne tuning
Retreat ne tunning
High,intermediate,
low speed toggle key
Press hold on
a second for
automatically y
Light switch
Press hold on
a second for
automatically landing
Press on the both sides
for emergency stop
4
●When charging the indicator light is out of state, after
completion of charging the indicator light is on, the charging
time is about 90 minutes.
●In the process of ight, when the battery is close to
exhausted, the LED light of the aircraft will ash for
prompting.
Preight preparation
1. Insert the USB cable into the computer or the
charger with USB mouth, then take the cable insert
to the lithium battery for charging.
5.There are many built-in precision electronic parts in
the aircraft, must to avoid the wet or water vapor
into the interior and lead to the failure and caused
by unexpected accident.
6.The aircraft must be far away from heat source,
prevent sunlight to avoid deformation of high
temperature even meltdown damage.
7.Do not arbitrarily remove or any modication of the
processing of this product, if have the use or
maintenance problems, please can consult the local
dealers, under their guidance to operate.
8.When using this product., be sure to abide by the
local laws and regulations, do not use it for any other
purposes other than legal provisions.
Adapter not include
5
2. Charging notes
●After the ight, the surface temperature of the battery will
rise, please place the aircraft for a few minutes, charging
after cooling.
●If no use for a long time, should be placed the aircraft and
battery in a cool and dry place, away from the heat source.
●When the battery is expanded, destroyed or severe fevered
etc. should immediately stop using.
●The lithium battery has a certain service life, when nd the
shorter ight time or slowly ight may need to replace the
lithium battery.
●In the process of charging the battery to prevent accidents
please place the aircraft and the charger on the ground or
in the place where there is no combustible materials.
3. Connect the power supply to the remote controller
Remote control power supply has two kinds, one is AA
size battery, another one is lithium battery, it is
recommended that using the lithium batteries in general,
dry battery only for emergency use.
Method A: Insert the lithium battery of the aircraft into the
inserting mouth of the battery in the remote
control, after placed well the battery then close
the battery cover.
6
Method B: Take two 1.5V AA batteries (batteries not
enclosed) in accordance with the direction to
install inside the battery of the remote control,
close the batteries cover.
Note: do not install backwards the battery, do not mix the
new and old batteries or dierent types of batteries.
Bind Frequency and adjust the acceleration
1. Power on the aircraft
Insert the battery into the power inserting mouth in the
battery, and cover well the battery, open the power supply
on the tail, at this time the LED lights of the aircraft begin
ashing, place the aircraft on a at ground or object to
adjust by the gyroscope, (if not at, after adjustment will
aect the ight eect )
2. Open the power supply of the remote control, the
indicator light starts ashing, push the left rocker of
the remote control to the upper then push to the
bottom (as shown in the below picture), at this time
enter into the searching frequency state, when the
LED lights of the aircraft turn to normal light, it
shows that the success of frequency.
7
3. After the success of frequency, pull the left and right
rocker of the remote controller together toward to
the inside below for 45 degrees angle, after the
remote controller sends out a “di” sound, at this
time the LED lights of the aircraft starts to ash
quickly,after becomes to normal light the
adjustment is completed, now can be ready to
take o.
Note: When the aircraft ight instability can also repeat
the steps 1-3 for adjusting the accelerometer.
Take O And Landing
Take o ----Method 1
Pull the left and right side rocker of the remote control
toward to the outside for 45 degrees angle, when the
remote controller sends out a “di” sound, at this time the
aircraft is unlocked successfully, the arm blades start slowly
rotating, then push up the left rocker then the aircraft can
be taken o.
When the remote control without any operation in ve
minutes will be automatically sleep o.
8
After the adjustment of the aircraft,hold on“L2” button
for a second,after the remote controller sends out a“di”
sound, the aircraft will take o to a certain height then
susbend in the sky.
Press hold on
a second for
automatically fiy
Take o ----Method 2
3. When landing the aircraft, can through the following
two methods. Method 1(shown in Figure 1) pull
down the accelerator rocker, the aircraft can fall to
the land. Method 2 (Figure 2) hold the “R2” button
for about a second, the aircraft will start automatic
landing (the right rocker can control the direction
while landing )
1 2
Press hold on
a second for
automatically landing
9
Press both buttons together to stop ight
High ,middle and low speed modes and lighting control
1. When press the“R1” button as shown above can
control the aircraft lights on and o.
2. When press the“L1” button as shown above will
switch the high,middle and low speed modes, LCD
screen will display the corresponding letters: H M L;
the buzzer will emit dierent sounds to distinguish,
a “Di” sound is low speed, “Di Di”sound is middle
speed, “Di Di Di” is high speed, th low speed mode
is suitable for the beginners learning to practice, the
medium spread is suitable for the advanced users
learning to practice, the high speed model is
suitable for the skilled users in ight.
Direction control during ight
1.Control the rise and fall
High,intermediate,
low toggle key
Light on/o switch
When you are in a state of emergency press the
“L2” and “R2”button to immediately stop the ight.
Emergency stop
Otros manuales para Q1012
1
Tabla de contenidos
