Toyama TE70O Manual de usuario

MOTOCULTIVADOR/TILLER

Dimensions / Dimensão / Dimensión

(mm) 1480×650×980

Net weight / Peso Líquido / Peso neto

(Kg) 100

Gross weight / Peso Bruto / Peso

bruto (kg) 115

Transmission system / Sistema de

Transmissão / Sistema de

transmisión

Gear / Engrenagem / engranaje

Cutting Width / Largura de corte /

Longitude del corte (mm) 240-650 mm

Tilling depth / Profundidade /

Profundidad (mm) 100-240

Speed control / Marcha / Marcha Forward, Neutral, Reverse / Ré, Neutro, Frente

/ reversa, neutro, frente

ENGINE / MOTOR / MOTOR

Model/modelo / Modelo TE70O

Type /Tipo / Tipo Single cylinder / Monocilíndrico, 4T, OHV 25,

air cooled / refrigerado a ar

Displacement / Cilindradas /

Cilindrada (cc)

212

Power max /Pot. Máxima /

Pot.máxima (HP/rpm)

(7.0) / 3600

Torque Máx / Torque máx. (n.m/rpm) 12 / 2,500

Starting system/ Sistema de

partida/Sistema de arranque

Recoil start / Partida retrátil / Arranque retráctil

Filtro de ar/Filtro de aire Oil Bath filter / Banhado a Óleo / Bañado en

aceite

Gasoline Tank capacity / Capacidade

tanque combustível / Capacidad

tanque de combustible (L)

3.6

Combustible consuption / Consumo

combustível/ Consumo combustible

(g/kW.h)

395

Engine oil capacity / Capacidade óleo

motor / Capacidad aceite en el motor

(L)

0.6

PREFACE

Thank you for purchasing TOYAMA Tilling.

This manual covers the operation and maintenance of a Tilling. The information and

specifications included in this publication were in effect at the time of approval for

printing. No part of this publication may be reproduced without written permission.

This manual should be considered a permanent part of the Tilling and should remain

with the Tilling if it is resold. The illustration may vary according to the type.

Keep this owner’s manual handy, so you can refer to it at any time. This owner’s

manual is considered a permanent part of the Tilling and should remain with the Tilling

if resold.

If a problem should arise, or if you have any questions about the Tilling, consult you

authorized dealer.

PREFACIO

Obrigado por comprar um Motocultivador TOYAMA.

Este manual contém informações para operação e manutenção do Motocultivador. As

informações e especificações incluídas nesta publicação estavam em vigor no momento

da aprovação para impressão. Nenhuma parte desta publicação pode ser reproduzida

sem permissão por escrito. A ilustração pode variar de acordo com cada modelo de

equipamento.

Mantenha este manual do proprietário perto, para que possa consultá-lo a qualquer

momento. Este manual é considerado uma parte permanente do Motocultivador e deve

permanecer com o Motocultivador se revendido.

Se surgir um problema, ou se você tem dúvidas sobre o Motocultivador, consulte o seu

revendedor autorizado TOYAMA.

PROLOGO

Gracias por comprar este Motocultivador TOYAMA.

Este manual cubre la operación y el mantenimiento del Motocultivador.La información

y las especificaciones incluidas en esta publicación son efectivas para la fecha de

aprobación de impresión.

Ninguna parte de esta publicación puede ser reproducida sin autorización.Este manual

debe ser considerado parte permanente del Motocultivador y debe mantenerse con el

producto en caso de ser revendido.Algunos detalles podrán cambiar dependiendo del

modelo.

Conserve este manual a la mano para que usted se pueda referir a él em cualquier

momento.

En caso de presentarse algún problema, o si usted tienen alguna pregunta sobre el

Motocultivador, contacte a su distribuidor TOYAMA.

INDICE

1. INTRODUCTION ........................................................................................................ 6

2. SECURITY INSTRUCTIONS ..................................................................................... 6

3. GENERAL CHART ..................................................................................................... 8

4. ASSEMBLY ................................................................................................................. 9

5. OPERATION ............................................................................................................. 12

6. ROTARY TILLER STATE ADJUSTMENT ............................................................ 14

7. ENGINE OPERATION .............................................................................................. 16

8. MAINTENANCE OF GASOLINE ENGINE ............................................................ 19

9. MAINTENANCE METHOD OF ROTARY TILLER .............................................. 21

10. COMMON FAULTS AND REMOVING WAYS ................................................... 22

1. INTRODUÇÃO .......................................................................................................... 24

2. INSTRUÇÕES DE SEGURANÇA ............................................................................ 24

3. COMPONENTES ....................................................................................................... 26

4. MONTAGEM ............................................................................................................. 28

5. OPERAÇÃO ............................................................................................................... 30

6. AJUSTES ................................................................................................................... 31

7. OPERAÇÃO DO MOTOR ........................................................................................ 33

8. MANUTENÇÃO DO MOTOR ................................................................................. 36

9. MANUTENÇÃO DAS FACAS ................................................................................. 38

10. GUIA SOLUÇÃO DE PROBLEMAS ..................................................................... 39

1. INTRODUCCIÓN .................................................................................................. 42

2. INSTRUCCIÓN DE SEGURIDAD........................................................................ 42

3. COMPONENTES ....................................................................................................... 44

4. MONTAJE ................................................................................................................. 45

5. OPERACIÓN .......................................................................................................... 47

6. AJUSTES ................................................................................................................ 49

7. OPERACIÓN DEL MOTOR .................................................................................. 50

8. MANTENIMIENTO DEL MOTOR ....................................................................... 54

9. MANTENIMIENTO DE LAS CUCHILLAS......................................................... 57

10. GUÍA SOLUCIÓN DE PROBLEMAS ............................................................... 57

1. INTRODUCTION

The preparation of land for agricultural, forestry or leisure activities implies

the use of different equipment, which is chosen according to the type of existing

material.

The Motorcultivator is a powerful single-axle combustion engine tool for

agricultural work, which can be driven by a driver on foot or even on a semi-

trailer.

This equipment is indicated for the cultivation of the earth in small properties

and its main function is to elevate and to reverse the ground to improve the

aeration and the infiltration of water. Among the highlighted function can also be

used in cleaning chicken bed, carriage, spray and small irrigations.

2. SECURITY INSTRUCTIONS

 Never allow an untrained person to operate the equipment.

 This machine should only be operated by adults.

 Isolate the work area, thus keeping unauthorized persons away from the

equipment.

 Never operate the equipment when you are tired, drunk or under the

influence of drugs. These conditions cause inattention.

 Before connecting the equipment, make sure that you know how to turn it

off in the event of an emergency.

 Before operating, check the condition of the equipment, check for cracks,

leaks, loose or missing screws, or any other malfunction. Only use the

equipment after performing the necessary repairs.

 Prolonged or improper work may cause injury. If you feel discomfort,

seek medical advice.

 Never touch the engine while it is hot. This can cause serious burns. If it

is necessary to touch it, wait for the equipment to cool completely.

 Try to feel secure and firm. Unbalancing yourself during the operation

can cause serious accidents.

 Always wear safety equipment such as goggles, ear protectors,

protective boots, protective clothing, rubber gloves, helmet and etc..

 To reduce the risk of accidents associated with the inhalation of exhaust

gases, do not operate in places with poor ventilation.

 Remove any jewelry, jewelry, rings, watches, and objects that may attach

to any part of the equipment.

 Carefully read all safety signs attached to the Power Generator and

observe all messages that follow the symbols to avoid possible injury or

risk of death.

DANGER：If you don’t operate as those indicated in the manual, serious injuries, even

death will be caused.

WARNING：If you don’t operate as those indicated in the manual, device damage and

injures will be caused.

ATTENTION：If you don’t operate as those indicated in the manual, device damage

and injures may be caused.

 Do not use radio or music headphones during the operation of the

machine.

 Do not wear loose, torn or bulky clothing around the machine.

 Fuels and lubricants are flammable materials, keep away from fire.

 To ensure your safety, please turn off the engine before refueling.

 Do not smoke or allow flames or sparks in your work area. The fuel is

extremely flammable and explosive, flames or sparks may ignite fuel

combustion.

 Only fill the tank when the engine is cold and in well ventilated areas.

 Do not switch on the equipment without fuel and / or lubricating oil in the

engine.

 Never operate equipment with protective covers removed. Keep feet,

hands, and hair away from moving parts to prevent bruising.

 Do not smoke near the equipment.

 Switch off the engine when it is not operating.

 Do not change or disable any safety device.

 Never leave appliance unattended.

 Keep the control elements of the appliance always dry, clean, free of oil

and grease. Control elements such as, for example, on / off switches,

accelerators, etc., must not be improperly locked, manipulated or altered.

3. GENERAL CHART

1. Hand control assy

2. Trailer

3. Mud fender

4. Rotary tilling equipment

5. Tilling box assy

6. Gear box assy

7. Gasoline engine

8. Belt transmission

9. Bumper

10. Belt cover

11. Front tire

12. Rear wheel

13. Clutch handle

14. Throttle handlebar

15. Steering column

16. Shut down switch

4. ASSEMBLY

Unpacking assembly

 Take out rotary tiller and accessories.

 Fix the body of rotary tiller, install walking wheels, then use pin 8×40 and

clip to fix them. Install rear wheels in the appropriate height, then use

lock bolt to fix it.

 Tilling/ditching blades installation: install tilling blades or ditching blades

on both sides of output shaft, edge towards forward, and then use pin

M8×40 and clip to fix it.

 Mud fender (or narrow mud fender) and side mud fender installation:

Install left and right mud fenders on the tiller, fixing with bolt M6×12 (8

pcs) and locknut M6 (8 pcs), and screw up by spanner. The adjustable

part of mud fender place is as the picture. Then install side mud fender

on both sides and screw up small handles.

 Handle bar installation: assemble handle bar components on tiller. The

handle bar frame position is symmetrical accordingly for the tiller, then

use the locked pin to fix the frame.

Installation and adjustment of cables

Adjustment of clutch cable(Look at picture 1 and picture 2)

 - Unlock nuts on the screw rod.

 - Instantaneously rotate the screw rod to show the shortest part of the handle bar.

 - Connect the clutch cable head into clutch plug behind the gear box assy, thread

the cable into axis pin M6×20, and fix with jump ring.

 - Properly pull down the clutch cable and fix the clutch cable head to handle bar

bottom.

 - Rotate out the screw rod and clip it repeatedly, unlock the clutch handlebar

until spring force of clutch can reset the bar, finally fasten the nuts.

Picture 1

Throttle

cable

Throttle

switch

Lock nut

Shut down

switch

Clutch

handlebar

Handlebar

lock

Clutch cable

Tabla de contenidos

Idiomas:

Otros manuales de Caña del timón de Toyama

Toyama

Toyama TDT100R-XP Manual de usuario

Manuales populares de Caña del timón de otras marcas

MTD

MTD 410R Manual de usuario

Craftsman

Craftsman 247.29931 Manual de usuario

MTD

MTD FRT Series Manual de usuario

Craftsman

Craftsman 917.298353 Manual de usuario

Troy-Bilt

Troy-Bilt Colt FT Manual de usuario

Ryobi

Ryobi 510r Manual de usuario

MTD

MTD OHV Series Manual de usuario

YAT

YAT YT5601-01 Manual de mantenimiento

Craftsman

Craftsman 917.296010 Manual de usuario

Troy-Bilt

Troy-Bilt OEM-290-260 Manual de usuario

Scheppach

Scheppach MTP560 Instrucciones de montaje

GARDEN WAY

GARDEN WAY 12194 Manual de usuario

Classen

Classen STAND-AER SA-25 Instrucciones de instalación y mantenimiento

Craftsman

Craftsman 850 Series Manual de usuario

DR PILOT 2 Guía de inicio rápido

Altrad

Altrad ATIKA BH 1400 N Guía

WIL-RICH

WIL-RICH 2500 Manual de usuario

Viking

Viking HB 685 Manual de usuario