Toshiba 29A3DE Guía de inicio rápido

SCHEMATIC DIAGRAM MODEL : 29A3DE / 29A3E / 29A3SH

WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY

PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL.

CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components

which have special characteristics important for safety and should be replaced only with types identical to those in the

original circuit or specified in the parts list. The mounting position of replacements is to be identical with originals.

Before replacing any of these components, read carefully the PRODUCT SAFETY NOTICE on the MANUAL for this

model. Do not degrade the safety of the receiver through improper servicing.

4. Voltages read with DIGITAL MULTI-METER from point indicated to chassing ground, using a color bar signal with all

controls at normal, line voltage 220 volts.

5. Waveforms are taken receiving color bar signal with enough sensitivity.

6. Voltage reading shown are nominal values and may vary ±20% except H.V.

NOTE:

1. RESISTOR Resistance is shown in ohm [K = 1.000, M = 1.000.000]. All resistors are 1/6W and 5%

tolerance carbon resistor, unless otherwise noted as the following marks.

1/2R = Metal or Metal oxide of 1/2 watt 1/2S = Carbon compsistion of 1/2 watt

1RF = Fuse resistor of 1 watt 10W = Cement of 10 watt

K = ±10% G = ±2% F = ±1%

2. CAPACITOR Unless otherwise noted in schematic, all capacitor values less than 1 are expressed in

?F, and the values more than 1 in pF.

All capacitors are ceramic 50V, unless otherwise noted as the following marks.

Electolytic capacitor Mylar capacitor

3. The parts indicated with " *" have special characteristics, and should be replaced with identical parts only.

–6 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

SERVICE MODE

1. ENTERING TO SERVICE MODE

(Service mode display)

Item

Data

3) While pressing the obutton,

press MENU button on TV set.

2) Press obutton again to

keep pressing.

2. DISPLAYING THE ADJUSTMENT MENU

1) Press MENU button on TV.

3. KEY FUNCTION IN THE SERVICE MODE

The following key entry during display of adjustment menu provides special functions.

A single horizontal line ON/OFF: - / - - button (on Remote) or abutton (on TV)

Test signal selection : abutton (on Remote)

Selection of the adjustment items : Channel s/t(on TV or Remote)

Change of the data value : Volume ;+/–(on TV or Remote)

Adjustment menu mode ON/OFF : MENU button (on TV)

Initialization of the memory (QA02) : CALL + Channel button on TV (s)

Reset the count of operating protect

circuit to “00”: CALL + Channel button on TV (t)

“RCUT”selection : 1 button

“GCUT”selection : 2 button

“BCUT”selection : 3 button

“CNTX”(or “SCNT”) selection : 4 button

“COLC”selection : 5 button

“TNTC”selection : 6 button

Test audio signal ON/OFF (1kHz) : 8 button

Self diagnostic display ON/OFF : 9 button

1) Press obutton once on

Remote Control.

Adjustment mode

Press

Service mode

Item

Data

Color thickness correction

note: Displayed differently as shown below, de-

pending on the setting of the receiving color

system.

COLP (PAL)

COLC (NTSC)

COLS (SECAM)

CAUTION : Never try to perform initialization unless you have changed the memory IC.

* The key function marked with are not usable to control in the Test signal for some model.

–7 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

4. SELECTING THE ADJUSTING ITEMS

1)Every pressing of CHANNEL sbutton in the service mode changes the adjustment items in the order of table-2.

(tbutton for reverse order)

Refer to table-2 for preset data of adjustment mode.

(See SETTING & ADJUSTING DATA on page 15)

5. ADJUSTING THE DATA

1) Pressing of VOLUME ;+/–button will change the value of data in the range from 00H to FFH. The variable range

depends on the adjusting item.

6. EXIT FROM SERVICE MODE

1) Pressing POWER button to turn off the TV once.

■INITIALIZATION OF MEMORY DATA OF QA02

After replacing QA02, the following initialization is required.

1. Enter the service mode, then select any register item.

2. Press and hold the CALL button on the Remote, then press the CHANNEL sbutton on the TV. The initialization of QA02 has

been complated.

3. Check the picture carefully. If necessary, adjust any adjustment item above.

Perform “Auto search Memory”on the owner’s manual.

CAUTION: Never attempt to initialize the data unless QA02 has been replaced.

7. TEST SIGNAL SELECTION

1) Every pressing of abutton on the Remote Control changes the built-in test patterns on screen as described below

in SERVICE MODE.

Signals Picture

•Red raster

•Green raster

•Blue raster

•All Black

•All White

•Black & White

•Black cross-hatch

•White cross-hatch

•Black cross-dot

•White cross-dot

•Black cross-bar

•White cross-bar

•Black cross-bar

on green raster

•H signal (white)

•H signal (black)

* The signals marked with are not usable to display in the Test signal for some model.

Signal off NTSC signals (14 patterns)

PAL signals (14 patterns)

–8 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

8. SELF DIAGNOSTIC FUNCTION

1) Press “9”button on Remote Control during display of adjustment menu in the service mode.

The diagnosis will begin to check if interface among IC’s are executed properly.

2) During diagnosis, the following displays are shown.

23******

POWER : 00

BUS LINE : OK

BUS CONT : OK

BLOCK : UV V1 V2

QV01

Part number of microcomputer (QA01)

Operation number of protecting circuit ----“00”is nor-

mal.

When indication is other than “00”, overcurrent apts to

flow, and circuit parts may possibly be damaged.

BUS LINE CHECK ----“OK”is normal.

“SDA1-GND”------------- SDA-GND short circuit.

“SCL1-GND”-------------- SCL-GND short circuit.

“SCL1-SDA1”------------- SCL-SDA short circuit.

BUS CONT ----“OK”is normal.

When indication shows “Q uuu NG”, the device with

the number may possibly be damaged.

BLOCK

UV : TV reception mode

V1 : VIDEO 1 input mode (a1)

V2 : VIDEO 2 input mode (a2)

Indicated color of mode now selected : Green and Red

Indicated color of other modes : White

Green : Normal

Red : The microcomputer operates to provide judgement

of no video signal. The red color is still indicated

though the signal is input, failure may exist in input

signal line including QV01.

QV01 : In case of indication green ---Normal

In case of indication red with input signal----

Failure may exist in output line including QV01.

NOTE: Component which controls character display on

screen is QT01 (TELETEXT IC.). If this display

function fails to operate due to damage in QT01,

self diagnosis procedure is as follows.

(1) In case that power indicator is blinking with

interval of 0.5 seconds; it means protecting cir-

cuit (Current limiter) is operating, and circuit

components may possibly be damaged. Check

related components.

(2) In case that power indicator is blinking with

interval of 1 second; Protecting circuit does

not operate, but a part of Bus line does not

operate normally. Check Bus line.











* The items marked with are not usable to display in the SELF DIAGNOSTIC FUNCTION for some model.

–9 –

GENERAL ADJUSTMENTS

SPECIFIC INFORMATIONS

DESIGN MODE

1. ENTERING TO DESIGN MODE

ITEM

DATA

S D Press

(Design mode) (Adjustment mode)

Press

3) Press MENU button on TV.

2) While pressing o(or CALL) button on

Remote and press MENU button on TV.

1) Select the Service mode.

2. SELECTING THE ADJUSTING ITEMS

Every pressing of CHANNEL tbutton in the design mode changes the adjustment items in the order of table-3.

(sbutton for reverse order)

Refer to table-3 for data of design mode.

(See SETTING & ADJUSTING DATA on page 15)

3. ADJUSTING THE DATA

Pressing of VOLUME sor tbutton will change the value of data.

When QA02 is initialized, items “OPT0”and “OPT1”of DESIGN MODE are set to the data of the representative model of this

chassis family.

Therefore, because ON-SCREEN specification remains in the state of the representative of model. This model is required to

reset the data of items “OPT0”and “OPT1”.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de TELEVISOR de Toshiba

Toshiba

Toshiba 28Z23G Manual de usuario

Toshiba

Toshiba CF35E50 Manual de usuario

Toshiba

Toshiba 27A43 Manual de usuario

Toshiba

Toshiba 21G3XHE Guía de inicio rápido

Toshiba

Toshiba 42 UA3A Series Manual de usuario

Toshiba

Toshiba 32WL55A Guía de inicio rápido

Toshiba

Toshiba 49L1763DA Manual de usuario

Toshiba

Toshiba CX27D60 Manual de usuario

Toshiba

Toshiba COLORSTREAM BBE 32AF44 Manual de usuario

Toshiba

Toshiba MD9DL1 Manual de usuario

Toshiba

Toshiba Easy Body Rider Manual de usuario

Toshiba

Toshiba 55TL515U Manual de usuario

Toshiba

Toshiba 14AF46C Manual de usuario

Toshiba

Toshiba 49U5766DB Manual de usuario

Toshiba

Toshiba CF27H40 Manual de usuario

Toshiba

Toshiba TL9 8 Digital Series Manual de usuario

Toshiba

Toshiba 50L5200U Instrucciones de montaje

Toshiba

Toshiba 27A41C Manual de usuario

Toshiba

Toshiba 55 QA4C Series Manual de usuario

Toshiba

Toshiba 32SL415U Instrucciones de montaje

Toshiba

Toshiba 34HX83 Manual de usuario

Toshiba

Toshiba 50L9450 Series Manual de usuario

Toshiba

Toshiba 32AF62 Manual de usuario

Toshiba

Toshiba CN27H95 Manual de usuario

Manuales populares de TELEVISOR de otras marcas

Philips

Philips Colour Television Manual de usuario

Philips

Philips 42PF9630A/37 Manual de usuario

Hitachi

Hitachi 32FX48B Manual de usuario

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manual de usuario

Changhong Electric

Changhong Electric uhd55b6000is Manual de usuario

Philips

Philips Matchline 21CE7551 Manual de usuario

Panasonic

Panasonic Genus TX-G10 Manual de usuario

Philips

Philips 25PT4523-16 Manual de usuario

Sony

Sony XBR-100Z9D Manual de usuario

Philips

Philips PR0930X3 Manual de usuario

Philips

Philips Brilliance 231P4QPY Manual de usuario

Samsung

Samsung 55S9 B Series Manual de usuario

Philips

Philips 32HF9385D Guía de solución de problemas

Sharp

Sharp LC-40FI5012E Manual de usuario

Loewe

Loewe Table Stand Reference 55 Manual de usuario

Philips

Philips 32PFH5300 Manual de usuario

Sylvania

Sylvania 6427FB Manual de usuario

Sanyo

Sanyo CE19LD90N-B Manual de usuario