Toshiba BMS-LSV6E Manual de usuario

Model:

BMS-LSV6E

INSTALLATION MANUAL

INTELLIGENT SERVER

CONTENTS

Precautions for Safety.................................................................................................................... 1

Before Installation .......................................................................................................................... 1

Intelligent Server Specifications ................................................................................................... 2

1 CF (Compact Flash) card Installation ....................................................................................... 3

2 Setting .......................................................................................................................................... 3

3 Installation.................................................................................................................................... 4

4 Cable Connection ....................................................................................................................... 6

• Thank you very much for purchasing this TOSHIBA INTELLIGENT SERVER.

• Please read this manual carefully beforehand for proper installation of the SERVER.

Precautions for Safety

• Read these “Precautions for Safety” carefully before installation.

• The precautions described below include important items regarding safety. Observe them without fail.

• After the installation work, perform a trial operation to check for any problem.

• Ask an authorized dealer or qualified installation professional to install or reinstall the

software.

• Perform installation work properly according to this Installation Manual.

• Do not modify the unit.

This may cause malfunction.

• Perform wiring correctly in accordance with specified the current capacity.

Failure to do so may result in short-circuiting, overheating, or fire.

• Connect the specified cables for the terminals securely to prevent external forces from

affecting them.

Failure to do so may result in disconnection, overheating, or fire.

• When providing services, perform the task after you confirm that you turned off the main

power supply, removed the power cord from the AC inlet, and the power was off.

CAUTION

Before Installation

No.

Quantity

Item

INTELLIGENT SERVER

Installation Manual

Cable

Closed end wire joint

Remarks

RS-485 cable for Intelligent Server

No.

Type

Wire size

Length

Type

Length

Signal line

For RS-485

For ethernet

Description

2-core shield wire

1.25 mm2, 500 m max. (total length)

LAN cable (higher than Category 5, UTP)

The appropriate use of straight cable/cross cable should be done

depending on your system used.)

100 m max

Use the following wiring materials to connect signal lines. (Procured on site)

Check the following package contents.

Prepare the following software (sold separately) before using the server.

Available software

Intelligent Server Software BMS-STCC E ( is 06 or higher)

BACnet Software BMS-STBN E ( is 06 or higher)

NOTE

Intelligent Server Specifications

Names of each parts

VGA

LAN2PS/2LAN1

USB

COM1

SDRRNL3OFFS1ONL2L1

L1 LED

L2 LED

S1 switch

L3 LED

Ethernet port2 (LAN2)

Ethernet port1 (LAN1)

CF CARD slot

Serial port1 (COM1)

RUN LED

Shut down switch

POWER switch

AC inlet (AC IN)

Specifications

Power Supply

Current

Operating temperature/humidity

Storage temperature

Dimension

Mass

COM port

LAN

220-240 VAC 50/60 Hz

0.2 A

0 to 40 °C, 10 to 90 %RH (no condensation)

-20 to 60 °C

250 (W) × 70 (H) × 145 (D) mm (292 (W) including the fixing metal plate)

1.5 kg

RS-485 (9-pin, D-SUB)

10BASE-T/100BASE-TX

External view

69.5

3.2

145

105

125

250

292

280

4.6

CF (Compact Flash) card Installation

• Do not insert or remove the CF (Compact Flash) card during power on of the Intelligent Server.

Doing so may cause a failure.

• If the CF (Compact Flash) card is not inserted properly, the Intelligent Server will not work.

REQUIREMENT

Insert the CF card (with the software sold separately)

Push the CF card fully into the slot.

Setting

CF card

Rating label

(1)Remove two screws and the cover plate and the CF card slot appears.

(2)Insert the CF card with its rating label attached surface upward.

Confirm the CF card is surely pushed into the slot.

The setting is not required.

S1 is set to “OFF”.

Intelligent Server Installation Method and Orientation

There are 2 types of setting methods and directions available for the server. Use the fixing metal plates

attached when installing the server.

Installation

(1)Surface mount

(2)Wall mount

Mount the server with the front face upward.

AC inlet side

(Unit : mm)

4 x

4.6

21 105

280

145

Fixing screw hole positions

Do not install the unit in any of the following places.

• Humid or wet place

• Dusty place

• Place exposed to direct sunlight

• Place where there is a TV set or radio within one meter

• Place exposed to rain (outdoors, under eaves, etc.)

REQUIREMENT

Installation (continued)

Installation Space and Maintenance Space

The installation space and the maintenance space must be determined before installation.

These spaces depend on installation method.

Installation Space

The values in the following table are required for installation space in each direction. Select an installation

place that allows good air ventilation.

Item

Installation space

Direction

Top

Bottom

Front

Rear

Right side

Left side

Surface mount

100

(*1) “Location adjacent to wall permitted” means that the unit can be installed close to the wall on that side.

Maintenance Space

Maintenance space is required for installation and maintenance of the unit.

Front

INTELLIGENT

SERVER

1000

Maintenance Space

Installation Space

(Unit: mm)

Rear

(unit: mm)

Top

Rear

Left side

Right side

Front

Wall mount – type A

100

Wall mount – type B

100

Location adjacent to wall permitted (*1)

Cable Connection

Power cable is not supplied for the Intelligent Server. Insert a three core power cord applicable to the

standard of the country you use. Be sure to connect the earth line of the power cable securely.

REQUIREMENT

• Insert an AC power cable into the AC inlet of the unit.

• Connect the power cord plug to an outlet (220 V - 240 V, AC).

• Disconnect the appliance from the main power supply. Connect this appliance to the main power

supply by a circuit breaker or a switch with a contact separation of at least 3mm.

• Make sure that the outlet is earthed.

REQUIREMENT

Ethernet wire Connection

Serial Port (RS-485) Connection

• Confirm that the power supply for the intelligent server is shut off.

• Connect RS-485 cable (packaged with the intelligent server) to Serial port 1 (COM1).

Fix the cable to the Intelligent Server by the fixing screws (two locations on both sides) attached to the

connector on RS-485 cable.

Connection to theTCS-NET Relay Interface

• TxRx(+) Connection

Connect three of the four wires of RS-485 wire (red wire/orange wire/wire from the terminal board RS-

485 A of the TCS-NET Relay Interface) together with the closed end wire joint. The red and orange

wires can be connected directly to the terminal board RS-485 A of the Relay Interface.

• TxRx(-) Connection

Connect three of the four wires of RS-485 wire (brown wire/yellow wire/wire from the terminal board RS-

485 B of the TCS-NET Relay Interface) together with the closed end wire joint. The brown and yellow

wires can be connected directly to the terminal board RS-485 B of the Relay Interface.

The RS-485 signal

wire has polarity.

If connected with

incorrect polarity, the

unit will not work.

Do not connect or

disconnect the wire

during control

operation.

Doing so may cause a

malfunction.

NOTE

• Insert the Ethernet wire into the Ethernet port1 (LAN1).

TCS-NET

Relay Interface

TCS-NET

Relay Interface

Intelligent Server

RS-485 cable

Brown/Yellow

Red/Orange

Shield wire open

(insulated)

Shield wire

earth connection

RS-485

Connect the shield

wires of the 2 wires

Closed end

wire joint

AC Power Cable Connection

• • • Trademarks: • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

• BACnet is a registered trademark of ASHRAE(American Society of Heating, Refrigerating and

Air-Conditioning Engineers, Inc.).

• Compact Flash and CF are trademarks of SanDisk Corporation.

• Ethernet is a registered trademark of Xerox Corporation.

• • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • • •

EH99861301

Tabla de contenidos

Otros manuales de Servidor de Toshiba