Toshiba RBC-CR1-PE Manual de usuario

AI CENTRAL REMOTE CONTROLLER

– 1 –

RBC-CR1-PE

AI CENTRAL REMOTE CONTROLLER OWNER’S MANUAL

TELECOMMANDE CENTRALE AI MODE D'EMPLOI

ZENTRALE FERNBEDIENUNG AI BENUTZERHANDBUCH

MANDO A DISTANCIA CENTRAL AI MANUAL DEL USUARIO

TELECOMANDO CENTRALE AI MANUALE DELL'UTENTE

AI CENTRALE AFSTANDSBESTURING GEBRUIKERSHANDLEIDING

1401449201R01

TOSHIBA

AI CENTRAL REMOTE CONTROLLER

– 2 –

●

This manual contains the operating instructions for the Remote Controller.

●

Please read this manual before operating your Air Conditioner.

●

For the indoor and outdoor units please refer to the respective Owner’s Manual.

●

Keep this manual in a convenient location for future reference.

●

Le présent manuel contient les consignes d’utilisation de la télécommande.

●

Ces consignes sont à lire avant d’utiliser le climatiseur.

●

Pour l’utilisation des unités intérieures et extérieures, se reporter aux modes d’emploi respectifs.

●

Conserver ce manuel dans un endroit adéquat pour pouvoir le consulter.

●

In diesem Benutzerhandbuch wird die Bedienung der Fernbedienung beschrieben.

●

Bitte lesen Sie dieses Handbuch vor Inbetriebnahme Ihrer Klimaanlage sorgfältig durch.

●

Für Innen- bzw. Außenanlagen lesen Sie bitte das jeweilige Handbuch.

●

Das Handbuch immer leicht auffindbar aufbewahren.

●

Este manual contiene las instrucciones para el manejo del mando a distancia.

●

Lea este manual detenidamente antes de usar su acondicionador de aire.

●

Para las unidades de interior y exterior consulte los manuales del usuario correspondientes.

●

Mantenga este manual en un lugar conveniente para poder consultarlo en el futuro.

●

Questo manuale contiene le istruzioni per l’uso del telecomando.

●

Leggere attentamente questo manuale prima di usare il condizionatore d’aria.

●

Per le unità interne ed esterne consultare i rispettivi manuali.

●

Conservare questo manuale a portata di mano per poterlo consultare in futuro.

●

In deze handleiding staan de bedieningsaanwijzingen voor de afstandsbesturing.

●

Lees deze handleiding door voordat u de airconditioning in werking stelt.

●

Voor de eenheden voor binnen- en buitengebruik: raadpleeg de respectieve gebruikershandleidingen.

●

Leg deze handleiding op een geschikte plaats zodat u deze in de toekomst gemakkelijk kunt raadplegen.

AI CENTRAL REMOTE CONTROLLER

– 3 –

YSTEM

UIDELINES

AND

UNCTIONS

AMES

AND

UNCTIONS

– C

ENTRAL

EMOTE

ONTROLLER

ISPLAY

ENTRAL

EMOTE

ONTROLLER

UTTON

PERATIONS

PERATION

ROCEDURE

INGLE

ROUP

ELECTION

ROCEDURE

NIT

ETTING

ROCEDURE

IMER

PERATION

ESTRICTION

ONITORING

AND

ILTER

IGN

ONTENTS

ÉNÉRALITES

ONCTIONS

ÉSIGNATIONS

ONCTIONS

– Z

ONE

AFFICHAGE

TÉLÉCOMMANDE

CENTRALE

OUTONES

ÉLÉCOMMANDE

ENTRALE

ROCÉDURE

ONCTIONNEMENT

ROCÉDURE

ÉLECTION

DES

NITÉS

ROCÉDURE

ÉGLAGE

DES

NITÉS

ONCTIONNEMENT

AVEC

ROGRAMMATEUR

IMITATION

ACCÈS

AUX

ONCTIONS

ONTRÔLE

ÉMOIN

ILTRE

OMMAIRE

LLGEMEINES

UND

UNKTIONEN

EZEICHNUNGEN

UND

UNKTIONEN

– A

NZEIGEFELD

DER

ENTRALEN

ERNBEDIENUNG

ASTEN

DER

ENTRALEN

ERNBEDIENUNG

ETRIEB

ÄHLEN

DER

NLAGEN

INSTELLEN

DER

NLAGEN

EITREGLERBETRIEB

INSCHRÄNUNG

DES

UGRIFFS

AUF

UNKTIONEN

BERWACHUNG

UND

FILTER-A

NZEIGE

NHALT

NTRODUCCIÓN

ISTEMA

UNCIONES

OMBRES

UNCIONES

– D

ISPLAY

DEL

ANDO

ISTANCIA

ENTRAL

UNCIONAMIENTO

LOS

OTONES

DEL

ANDO

ISTANCIA

ENTRAL

ÉTODO

PERATIVO

ÉTODO

ELECCIÓN

UNA

NIDAD

NDIVUDAL

RUPO

NIDADES

ÉTODO

ROGRAMACIÓN

UNA

NIDAD

UNCIONAMIENTO

DEL

IMER

IMITACIÓN

DEL

UNCIONAMIENTO

ONITORIZACIÓN

ÍMBOLO

DEL

ILTRO

ENERALITÀ

UNZIONI

OMI

UNZIONI

– D

ISPLAY

DEL

ELECOMANDO

ENTRALE

UNZIONI

DEI

ULSANTI

DEL

ELECOMANDO

ENTRALE

ROCEDURA

PERATIVA

ROCEDURA

ELEZIONE

DELLE

NITÀ

ROCEDURA

EGOLAZIONE

DELLE

NITÀ

UNZIONAMENTO

DEL

IMER

MPOSTAZIONE

DELLE

IMITAZIONI

UNZIONAMENTO

ONITORAGGIO

IMBOLO

DEL

ILTRO

NDICE

ICHTLIJNEN

OOR

YSTEEM

UNCTIES

ENAMINGEN

UNCTIES

– D

ISPLAY

VAN

ENTRALE

FSTANDSBESTURING

ERKING

VAN

NOPPEN

VAN

ENTRALE

FSTANDSBESTURING

ROCEDURE

VOOR

ERKING

TELLEN

ELECTIEPROCEDURE

FZONDERLIJK

ROEP

ROCEDURE

ENHEID

TELLEN

ERKING

VAN

IMER

EPERKING

VAN

ERKING

ONTROLE

ILTERSYMBOOL

NHOUD

ONTENIDO

AI CENTRAL REMOTE CONTROLLER

– 4 –

The Central Remote Controller can control up to 16 individual indoor units.This controller can control

individually or collectively the indoor units connected to the Central Remote Controller.All of the functions of the

air conditioners can be controlled. It is also possible to combine the 7 Day Timer (RBC-WT1-PE) with this

Central Remote Controller.

UNCTIONS

CENTRAL CONTROL

Separate control and display for the each of the indoor units connected.

CONTROL OF THE INDOOR UNIT FROM ITS REMOTE CONTROLLERS

The air conditioner can be controlled by the Central Remote Controller and by a Standard Remote Controller in

the modes below.

Last push priority: All air conditioner functions can be changed by either Remote Controller.

Central: The air conditioner settings can be modified by the Central Remote Controller.

The air conditioner can only be switched on and off by the Standard Remote Controller.

Central Locked: The air conditioner is locked in the off position.

FILTER SIGN

As a reminder to clean the filters this is displayed on the Standard Remote Controller and Central Remote

Controller.

STANDBY

In case of usage with 2 pipe multi systems cooling can be over ruled by heating. In this case Standby is

displayed.

POWER FAILURE

The Central Remote Controller has a built in battery backup for power failure. This lasts for around 72 hours

after a full charge of 120 hours.

TIMER OPERATION

When connected with the 7 DayTimer (RBC-WT1-PE) the Central Remote Controller can control the scheduled

timer operations.

YSTEM

UIDELINES

AI CENTRAL REMOTE CONTROLLER

– 5 –

AMES

AND

UNCTIONS

– C

ENTRAL

EMOTE

ONTROLLER

ISPLAY

All of the display items are shown in the diagram below for the purpose of explanation. Only selected items are

displayed in actual operation.

1 ON/OFF Display

This displays the operating status of the unit that is

shown in the unit display.

2 Unit Display

This number indicates the selected unit.

3 MONITOR / SET Display

In normal operation monitor is displayed when unit

setting is required SET flashes.

4 UNIT / ALL Display

When all units are selected UNITALL is displayed.

5 Connected Unit Display

This display indicates the connected units and their

operating status.

6 MODE Display

Displays selected operation mode.

7FANDisplay

Displays selected fan speed.

8 TEMP Display

This display shows the set temperature.

9 CHECK Display

This display appears when the air conditioner is in

the check mode.

10 LOUVER or LOUVER Display

MANUAL

LOUVER is displayed if the automatic louvers are

driven.LOUVERMANUALisdisplayedifautolouver

is selected but not available.

11 TIMER Display

This is displayed when a unit is being associated

with a 7 Day Timer.

12 FILTER Display

This display appears after 2500 hrs of operation.

13 STANDBY Display

This is displayed if the air conditioner is connected

to a super multi system when operation is being

disabled.

14 LOCKED Display

This is displayed if air conditioner is locked in the

off position by the Central Remote Controller.

15 CENTRAL Display

This is displayed if air conditioner operation is

being restricted by the Central Remote Controller.

AI CENTRAL REMOTE CONTROLLER

– 6 –

ENTRAL

EMOTE

ONTROLLER

UTTON

PERATIONS

1 MONITOR/SET Button

Thisisusedtoselectthemonitoringorsettingmodes

for the Central Remote Controller.

2 SINGLE SELECT Button

This is used to individually select an indoor unit

connected to the Central Remote Controller.

3 SELECT ALL Button

This is used to set same operating conditions for all

of the connected indoor units.

4 ON/OFF Buttons

These buttons are used to turn the air conditioners

on or off.

5 SELECT CONTROL Button

This is used to supervise different levels of

operation at the Standard Remote Controller.

6 MODE Button

Selects the desired operation mode, each time it is

pressed the display changes in the following

sequence:-

FAN ONLY

→

COOL

→

HEAT

→

AUTO

7FANButton

Selects the desired fan speed mode, each time it is

pressed the display changes in the following

sequence:-

AUTO

→

HIGH

→

MED

→

LOW

8 LOUVER Button

This is used to drive the outlet louvers automati-

callywhenthe air conditioner isinoperation. When

it is pressed the louvers will start oscillation and

LOUVERwill be displayed, whenitispressedagain

the louvers will stop. If no automatic louvers are

fitted and this button is pressed then LOUVER

MANUAL is displayed.

9 TEMPADJUST Buttons

▼▲

These buttons are used to set the required room

temperatures (18-29 ˚C).

10 TIMER Button

This button is used to enable operation with a

7 Day Timer.

11 CHECK Button

Displays fault codes for the use of the Service

Engineer.

12 FILTER Button

This button is used to reset the filter display.

AI CENTRAL REMOTE CONTROLLER

– 7 –

→→

Procedure Page Remarks

Supply power to Central Remote Controller

and the respective indoor unit.

STARTING THE CONNECTED AIR CONDITIONERS

To start the air conditioner press the MONITOR/SET 8 The display changes from monitor to set.

button.

Select the setting mode 8

a) SINGLE SELECT The operational conditions for one air

conditioner or group.

b) SELECT ALL

The operational conditions for every air condit-

ioner connected to the Central Remote Controller.

Setting of the operation modes and fan speeds 9The settings can be verified by looking

are carried out by pressing the respective buttons. at the LCD display.

To start the air conditioner press the ON button. 8

Select the restriction in use by pressing 11

SELECT CONTROL.

NO DISPLAY 11 Last touch priority.

CENTRAL In the Central mode, operation of the air

conditioner is restricted to ON/OFF operation.

LOCKED In the Locked mode the air conditioner

remains in the OFF mode.

Press the MONITOR/SET button. 8To register the changes the Central Remote

Controller will change to monitor. The

respective air conditioners will start.

● If the new settings are not registered by pressing the MONITOR/SET button within 15 seconds of the last change the

status of the Central Remote Controller will revert to the monitor mode without changing any settings.

STOPPING CONNECTED AIR CONDITIONERS

To stop the air conditioner press the 8The display changes from monitor to set.

MONITOR/SET button.

To select the air conditioner to be switched off press 8

the SINGLE SELECT button or press the

SELECT ALL button if you wish to stop every unit.

Press the OFF button. 8

Press the MONITOR/SET button. 8To register the changes the Central Remote

Controller will change to monitor. The

respective air conditioners will stop.

PERATION

ROCEDURE

AI CENTRAL REMOTE CONTROLLER

– 8 –

INGLE

ROUP

ELECTION

ROCEDURE

●If the new settings are not registered by pressing the set key within 15 seconds of the last change the status

of the Central Remote Controller will revert to the monitor mode without changing any settings.

●If an air conditioner is connected to the Central Remote Controller its number will appear in the connected

unit display. If the unit is in the on state, the number will be underlined.

1 MONITOR/SET Button

Select the setting mode by pushing this button. SET

will begin to flash on the display.

2 SINGLE SELECT Button

Select the unit whose settings require modification

by pressing this button. Each time this button is

pressed the display scrolls through the number of

each connected indoor units.

3 SELECT ALL Button

If all of the air conditioners connected to the Central

Remote Controller require the same setting press

this button and they will be selected: SET ALL will

flash.

4Indoor unit setting this is explained in detail

on the following page.

5 ON/OFF Button

When this button is pressed the selected air condi-

tioner will be switched on or off.

6 MONITOR/SET Button

The display changes from SET to MONITOR.

To register changes to the operating conditions of

the air conditioners press this Button.

Example

Connected Unit Window

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

9 10 11 12 13 14 15 16 9 10 11 12 13 14 15 16

16UnitsConnectedbut in the

OFF Status 16 Units Connected but in the

ON Status

AI CENTRAL REMOTE CONTROLLER

– 9 –

NIT

ETTING

ROCEDURE

1 MONITOR/SET Button

Select the setting mode by pushing this button. SET

will begin to flash on the display.

2 SINGLE SELECT / SELECT ALL Buttons

Select the unit(s) whose settings require modifica-

tion by pressing these buttons.

3 MODE Button

Select the required mode by pressing this button.

FAN ONLY

→

COOL

→

HEAT

→

AUTO

4 FAN Button

Select the required fan speed by pressing this

button.

AUTO

→

HIGH

→

MED

→

LOW

5 TEMP ADJUST Buttons ▼▲

These keys are used to set the required room

temperatures (18-29 ˚C).

●

In the AUTO mode the fan speed changes

according to the room temperature.

6 LOUVER Button

If the unit has a motor driven louver it can be

switched on and LOUVER will be displayed.

7 ON/OFF Button

When this key is pressed the selected air

conditioner will be switched on or off when the set

button is pressed.

8Toregister changes to the operating conditions

of the air conditioners press the MONITOR/SET

Button.

The display changes from set to monitor.

●

If the operation of the air conditioner is stopped and immediately restarted by pressing the ON/OFF Button,

the air conditioner will not operate for 3 minutes to protect the unit.After the three minutes the unit will be

allowed to start.

Starting of the Heating operation

●

After the pre heat defrost operation that lasts for 3 to 5 minutes with the indoor fans stopped.The fans will

then operate at the set fan speed.

Starting of the Cooling operation

●

The air conditioner will start in the cooling mode after approximately 1 minute.

AI CENTRAL REMOTE CONTROLLER

– 10 –

IMER

PERATION

The timer function is available from the separate 7 DayTimer (RBC-WT1-PE) the timer is connected directly to

the Central Remote Controller.

●

The selected air conditioner can be switched on or off by the timer.

1 MONITOR/SET Button

Select the setting mode by pushing this button. SET

will begin to flash on the display.

2 SINGLE SELECT / SELECT ALL Buttons

Select the unit(s) whose settings require

modification by pressing these buttons.

3 TIMER Button

To select the timer press the timer button this

associatesthe connectedtimerwith theselectedunit.

If TIMER is not displayed it is not associated with

that unit.

4Indoor unit setting is explained in detail on

page 9.

5Toregister changes to the operating conditions

of the air conditioners press the MONITOR/SET

Button.

The display changes from SET to MONITOR.

Otros manuales de Mando a distancia de Toshiba

Toshiba

Toshiba RBC-AMS55E-EN Manual de usuario

Toshiba

Toshiba RBC-AMS51E-EN Manual de usuario

Toshiba

Toshiba RBC-SR1-PE Manual de usuario

Toshiba

Toshiba Carrier RBC-AMS41UL Manual de usuario

Toshiba

Toshiba RBC-AXU33UP-E Manual de usuario

Toshiba

Toshiba RBC-AX32UW-UL Manual de usuario

Toshiba

Toshiba RBC-AX22CE Manual de usuario

Toshiba

Toshiba TCB-SC643TLE Manual de usuario

Toshiba

Toshiba 15V300PG Manual de usuario

Toshiba

Toshiba RBC-SRC-PE Manual de usuario

Toshiba

Toshiba CT-8002 Manual de usuario

Toshiba

Toshiba RBC-AX23UWW-E Manual de usuario

Toshiba

Toshiba A3030D series Manual de usuario

Toshiba

Toshiba RBC-AX32CE2 Manual de usuario

Toshiba

Toshiba TCB-SC642TLE Manual de usuario

Toshiba

Toshiba RBP-RC001-E Instrucciones de funcionamiento

Toshiba

Toshiba RBC-IR2-PE Manual de usuario

Toshiba

Toshiba RBC-AMT32E Manual de usuario

Toshiba

Toshiba RBC-AMS54E-UL Manual de usuario

Toshiba

Toshiba WH-H1JE2 Manual de usuario

Toshiba

Toshiba RBC-AMT32E Manual de usuario

Toshiba

Toshiba RBC-AS21E Manual de usuario

Toshiba

Toshiba TCB-SC643TLE Manual de usuario

Toshiba

Toshiba RBC-AS21UL Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación