Toshiba RBC-ASCU11-E Manual de usuario

Pocket Quick

Reference Guide

On the TOSHIBA

Compact Simple Wired

Remote Controller

RBC-ASCU11-E

Cool Designs Ltd makes every effort to ensure that the information provided within this publication is correct and error free, however we cannot guarantee that it is free of inaccuracies, errors, or

omissions. Users should seek to clarify this information for themselves prior to basing any decisions upon such information.

Toshiba air conditioning’s

Latest addition to their wired remote controller portfolio.

The RBC-ASCU11-E.

A small, 86 x 86 x 16mm wired remote controller,

With simple control keys, (5).

Large backlite LCD display.

Fault Diagnostics.

Monitor Function.

DN Code access.

ON / Off Timer.

Room Temperature Sensor.

86mm

Buttons.

Menu.

Timer.

Up/ Down.

Power Button, illuminated when system is ON

Blinks when a fault is detected or when a protection device activates.

Display, Top line.

Louver position.

Automatic Mode.

Heat Mode.

Dry Mode.

Cool Mode.

Fan Only Mode.

Central Control Indicator.

Display middle Right.

Protection device activated.

SETTING. System auto checking after power down.

Temperature set point,

(Can be configured either single increments or

0.5 increments, via bit switch on rear.)

TEST -Test mode selected.

Display Middle Left.

Running standby indicator (VRF)

Preheat indicator.

Self-clean operation.

Timer, (Off timer 0.5hr to 24hr.)

Remote sensor indication.

Display bottom right.

Fan - Fixed speed selected.

Auto fan speed.

Specific Fan speed.

Troubleshooting.

Active fault.

If the system encounters a fault,

The check code will be automatically

Displayed in the “Timer Off” window,

Bottom left display.

The display will automatically scroll

and display the reference of the

affected unit.

For troubleshooting history.

The “history” can store 4 codes.

To access the history, long press

(10 seconds) the “Timer” button.

To scroll through the codes,

press “UP/Down”.

Do not press the “Menu” button for more than 10 seconds as this will erase the history.

To erase the memory, press the “Menu” button for more than 10 seconds.

Monitor mode.

To enter “Monitor” mode.

With the system ON, (power light illuminated).

Press and hold the “Menu” button for 10 seconds,

Then press the “Timer” button.

In Monitor mode, data is displayed from indoor units and outdoor units.

The “Code” is displayed in the right-hand

display, “No. ##”.

To scroll through the “Codes” use the

“UP/DOWN” buttons

The “Data”from the respective component is

displayed in the bottom left-hand display

“####” (Read ONLY).

To exit “Monitor” mode,

press the “Menu button”.

Code

Indoor Data

Code

Outdoor Data

Room Temp (Control Temp) (°C)

TE Sub-cooled Liquid Temp (°C)

Room Temp (Remote Controller) (°C)

TO Ambient Temp (°C)

TA Return Air Temp (°C)

TD Discharge Temp (°C)

TCJ Coil Liquid Temp (°C)

TS Suction Temp (°C)

TC Coil Vapour Temp (°C)

THS Inverter Heat Sink Temp (°C)

Fan Speed (rpm)

Operation Current (x1 1/0) (A)

Fan Run Time (x 100h)

TL Liquid Temp (°C)

Filter Duration Timer (x 1h)

Compressor Frequency (rps)

Fan Speed (Lower) (rpm)

Fan Speed (Upper) (rpm)

Compressor Run Time (x 100h)

For Digital/ Super Digital inverter R32 equipment.

For “e” series (SMMSe & SHRMe) R410A VRF equipment.

Code

Outdoor Data

Code

Outdoor Data

Pd – High Pressure Sensor (x100) (MPa)

PMV 1 Opening

Ps – Low Pressure Sensor (x100) (MPa)

PMV 3 Opening

Td1 – Compressor 1 Discharge Temp (°C)

PMV 4 Opening

Td2 – Compressor 2 Discharge Temp (°C)

#3 1 Fan model: Comp. 1 Current (x10) (A)

2 Fan model; Comp. 1 and Fan current (x10) (A)

TE1 – Outdoor Coil Temp (°C)

TE2 – Outdoor Coil Temp (°C)

#4 1 Fan model: Comp. 1 Current (x10) (A)

2 Fan model; Comp. 1 and Fan current (x10) (A)

TO – Outdoor Ambient Temp (°C)

TS1 – Suction Temp (°C)

Compressor 1 revolutions

TS2 – Suction Temp (°C)

Compressor 2 revolutions

TL – Liquid Temp (°C)

Outdoor fan mode

Compressor IPDU 1 Heat Sink Temp (°C)

Heating/cooling recovery controlled

Compressor IPDU 2 Heat Sink Temp (°C)

Pressure release

Outdoor Fan IPDU 1 Heat Sink Temp (°C)

Discharge temperature release

Outdoor Fan IPDU 1 Heat Sink Temp (°C)

Follower unit release

Outdoor unit horsepower (HP)

Note

* Would be replaced with 1 = U1,2 = U2 or 3 = U3

to obtain data from respective outdoor unit.

Would be replaced with 5 = U1, 6 = U2 or 7 = U3

to obtain data from respective outdoor unit.

For “u” series (SMMSu) R410A VRF equipment.

Code

Outdoor Data

Code

Outdoor Data

Pd – High Pressure Sensor (x100) (MPa)

TK1 – Compressor oil temp. (oC)

Ps – Low Pressure Sensor (x100) (MPa)

TK2 – Compressor oil temp. (oC)

Td1 – Compressor 1 Discharge Temp (°C)

PMV1 – Opening (pls)

Td2 – Compressor 2 Discharge Temp (°C)

PMV2 - Opening

TS1 – Suction Temperature (°C)

PMV3 - Opening

TS3 – Suction Temperature (°C)

PMV4 - Opening

TE1 – Outdoor Coil Temp (°C)

Compressor 1 current (x10) (amps)

TE2 – Outdoor Sub heat exchanger temp.

Compressor 2 current (x10) (amps)

TE3- Outdoor Sub heat exchanger temp.

Compressor 1 revolutions (x10) (rps)

TO – Outdoor Ambient Temp. (°C)

Compressor 2 revolutions (x10) (rps)

TL1 – Liquid Temp. (°C)

Outdoor fan mode

TS2 – Suction Temp. (°C)

TH1 - Inverter of compressor 1 heat sink temp.

TS3 – Suction Temp. (°C)

TH2 - Inverter of compressor 2 heat sink temp.

TG1 – Outdoor coil Temp (°C)

TH fan1 -Inverter of outdoor fan 1 heat sink

TG2 – Outdoor coil Temp (°C)

TH fan2 -Inverter of outdoor fan 1 heat sink

TG3 – Outdoor coil Temp (°C)

Outdoor unit horsepower (HP)

Note

* Would be replaced with 1=U1, 2=U2, 3=U3, 4=U4 & 5=U5

to obtain data from respective outdoor unit.

Would be replaced with 6=U1, 7=U2, 8=U3, 9=U4 & A=U5

Dip Switches.

In the rear of the controller there is a bank of 6 “Dip” switches.

These allow for certain functions to be enabled or disabled.

1) Header/Follower, this allows for more than one remote controller to be connected to a system.

(Default setting OFF – Header)

2) LCD Back Light, this turns ON/OFF the back-light display. (Default setting OFF, Light ON).

3) Temp. Set, this allows for the temperature to be displayed /selected as a whole or a decimal i.e.

21oC Dip switch ON, 21.5oC Dip switch OFF. (Default setting OFF 0.5oC).

4) Remote Sensor, this will set the “Return Air – TA” at the remote controller, (Default is OFF – Return Air –

TA at the indoor unit.)

5) Press and Hold 4 Sec. This will change the operation mode of the ON/OFF switch, the button will

need to be pressed and held for 4 seconds or more to turn ON/OFF the system. (Default OFF – No delay.)

6) Reduces the brightness of the operation indicator lamp of the remote controller, set the lamp to be

dim when the switch is turned on and bright when the switch is turned off. (Default OFF – Bright)

For “DN Code” access.

The RBC-ASCU11-E remote can also be used by service/installation engineers to access the configuration

menu, “DN Codes”

With power applied but the system OFF,

i.e. the power light is NOT illuminated.

Press and hold for 10 seconds the “Menu”

button and the “Down button”

Once the display changes then press the

“Timer” button.

The system automatically starts at “DN Code” 10.

Scroll through the “DN Codes” using the

“Up/Down” buttons.

To move to “Data” (Bottom left display)

press the “Menu” button.

To change the “Data” use the “Up/Down” buttons.

To “Fix” a change to the “Data” press the

“Timer” button.

To end press the “Power Button”

NOTE.

The new “UP” range of VRF indoor units and the new “U” series outdoor units (SMMSu)

utilize a range of new “DN” codes, some of which are now three-digit codes, when

accessing a three-digit code the last digit is slightly smaller than digits one and two.

DN Code 103 (3 figure)

DN Code 03 (2 figure)

Otros manuales para RBC-ASCU11-E

Tabla de contenidos

Otros manuales de Mando a distancia de Toshiba

Toshiba

Toshiba CT-8002 Manual de usuario

Toshiba

Toshiba Carrier RBC-AX22CUL Manual de usuario

Toshiba

Toshiba Carrier RBC-AMS41UL Manual de usuario

Toshiba

Toshiba 15V300PG Manual de usuario

Toshiba

Toshiba RBC-AX22CE2 Manual de usuario

Toshiba

Toshiba RBC-AMS41E Manual de usuario

Toshiba

Toshiba RBC-AS41E Manual de usuario

Toshiba

Toshiba RAV Heat Manual de usuario

Toshiba

Toshiba RBC-IR1-PE Manual de usuario

Toshiba

Toshiba RB-RWS20-E Manual de usuario

Toshiba

Toshiba RBC-AMT21E Manual de usuario

Toshiba

Toshiba 2358 9721 Manual de usuario

Toshiba

Toshiba A3030D series Manual de usuario

Toshiba

Toshiba RBC-AMTU31-E Manual de usuario

Toshiba

Toshiba RBC-ASC11E Manual de usuario

Toshiba

Toshiba MML-AP0074NH-E Manual de usuario

Toshiba

Toshiba RBC-IR2-PE Manual de usuario

Toshiba

Toshiba Regza 32WLT68 Manual de usuario

Toshiba

Toshiba RBC-AMS54E Manual de usuario

Toshiba

Toshiba RBC-AMS41E Manual de usuario

Toshiba

Toshiba RBC-AXU33UP-E Manual de usuario

Toshiba

Toshiba TCB-SC640U-E Manual de usuario

Toshiba

Toshiba RBC-AS21UL Manual de usuario

Toshiba

Toshiba TCB-AX21U-E Manual de usuario

Manuales populares de Mando a distancia de otras marcas

Panasonic

Panasonic EUR7622KB0 Manual de usuario

Bang & Olufsen

Bang & Olufsen Beo4 Manual de usuario

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Manual de usuario

Multiplex

Multiplex PROFI TX 9 Manual de usuario

One Remote

One Remote RMB4 Manual de usuario

FUTABA

FUTABA 9ZAP - PART2 Manual de usuario

HR Matic

HR Matic HR MULTI 3 Manual de usuario

Yamaha

Yamaha ACC-GNRST-30-20 Manual de usuario

EisSound

EisSound KBSOUND Manual de usuario

Marantz

Marantz RC101 Manual de usuario

Conrad

Conrad FS20 TC6 Manual de usuario

Anritsu

Anritsu MP1777A Manual de usuario

Niles

Niles WVC100 Guía de solución de problemas

RCA

RCA RCU1300 Manual de usuario

Bang & Olufsen

Bang & Olufsen BEO6 Manual de usuario

GE 94901 Manual de usuario

Onbon

Onbon YQ1-75 Manual de usuario

FUTABA

FUTABA R7108SB Instrucciones de instalación