Toshiba SD-R1102 Manual de usuario

TOSHIBA AMERICA INFORMATION SYSTEMS

STORAGE DEVICE DIVISION

IRVINE, CALIFORNIA

SD-R1102

CD-RW/DVD-ROM COMBO DRIVE

USER MANUAL

CONTENTS

Introduction..............................................................................1

Setup ........................................................................................3

Using the Combo Drive...........................................................6

Troubleshooting.......................................................................9

Specifications ........................................................................10

Drive Connectors...................................................................13

INTRODUCTION – SD-R1102

General Features

Reads and records digital data on CD-R/-RW discs at 2X, 4X and 8X

3-way Disc Eject (eject button, software, emergency eject hole)

Average Random Access Time

CD 110ms

DVD-ROM 150ms

Horizontal or Vertical Mount

2MByte Buffer

Playback interchangeability for CD-ROM and DVD-ROM discs

Regionalization (RPC2 compliance) (DVD)

BUS Interface - ATAPI

Types of Disc Formats Supported - Write

•Applicable Write Format CD-R, CD-RW: Disc at once, Track at one, Session at once,

Packet write

•Applicable Write disc CD-R/-RW: CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-

ROM XA, MIXED MODE CD, CD-I, CD-I Bridge, (Photo-CD, Video-CD), Multi-session CD

(Photo-CD, CD EXTRA, Portfolio, CD-R/RW), CD-R/RW

Types of Disc Formats Supported - Read

DVD:

DVD-ROM, DVD-R

CD:

CD-DA, CD+(E)G, CD-MIDI, CD-TEXT, CD-ROM, CD-ROM XA, CD-I, CD-I Bridge (Photo-CD,

Video-CD), Multi-session (Photo-CD, CD-EXTRA, CD-R, CD-RW, Portfolio), CD-R, CD-RW

Front Panel

Figure 1.SD-R1102 DVD Writeable Drive Front Panel

Loading Tray Load disc using tray

LEDs The LED lights green or amber when the drive is operating (LED is amber

when drive is writing.)

Load/Unload Button The Load/Unload button is used to open the disc tray so you can install or

remove a disc.

Emergency Eject Hole The emergency eject hole is to be used only when the Loading Tray will not

open when Eject button is pressed

SETUP – SD-R1102

The following steps must be performed to properly install your drive:

•Set Drive Jumper Settings

•Connect Audio Cable

•Attach IDE BUS Cable

•Attach Power Cable

•Mount Drive

Jumper Settings

The mode select jumpers are 6 straight angle pins located on the rear of the Combo drive.

By placing a jumper on the pins, you can select the following functions:

Drive is configured using host interface signal CSEL

SL Configures drive as Slave

MA Configures drive as Master (default mode)

Figure 1.Mode Select Jumper

In most installations, jumper should remain in the MA position (factory default). It is recommended that

you install your Combo drive only on the secondary IDE BUS. If you are installing on primary IDE BUS,

your hard drive would then be the Master, and you should set your Combo drive to the Slave position

(SL)

Figure 2.Jumper Locations

Placing Combo Drive inside your Computer

Now that you have set the jumpers, you are ready to install your Combo drive inside your computer.

Important Note: Disconnect power from your computer system before beginning installation.

Remove computer cover and faceplate if required. Refer to your computer systems manual for removal

information. If the Combo drive is replacing a CD-ROM or DVD-ROM, remove drive presently installed in

your system.

Your Toshiba Combo drive can be placed in any free half-height drive slot at the front of your computer.

(It can be mounted horizontally or vertically.)

Carefully start sliding the Combo drive into the opening with the disc tray facing the front of the computer.

Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio cable and

the Power cable on the back of the drive.

Connecting Cables

IDE BUS Cable (not supplied with drive) - Your computer system should have a primary and secondary

IDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUS

cable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the Combo

drive's interface connector:

If you are replacing your CD-ROM or DVD:

connect Combo drive to the BUS Cable connector that

the CD-ROM or DVD was connected to.

If Combo drive is not replacing a CD-ROM/DVD or is an

addition to a CD-ROM/DVD:

connect Combo drive to an open connector on the

secondary IDE BUS cable (not supplied with drive).

If Combo drive is to be slave on Primary BUS:

connect Combo drive to open connector on the primary

IDE BUS cable (not supplied with drive).

Figure 3.Installing BUS Cable

Power Cable - Connect an internal computer power

supply cable to the power socket at the back of the

Combo drive. One side of the plug has chamfered

edges, so the power connector fits only one way. Push

plug completely into the socket making sure the plug fits

correctly.

Figure 4.Installing Power Cable

Audio Cable (optional) - If you have a sound card and

speakers, and would like to play audio CDs on your

computer, you will need to install a CD/DVD audio cable.

Toshiba's Combo drives use a standard 4-pin audio

cable that can be purchased from most local computer

suppliers. The sound cable connects to your sound card

at one end and the other end connects to the digital

audio connector at the left rear of the Combo drive (see

Combo drive Back Panel photo for location). Refer to the

instructions that came with your sound card for details

on any sound-driver software required.

Figure 5.Installing Audio Cable

Completing Installation

After you have connected all the necessary cables,

push the Combo drive completely into the computers

drive slot. Mount drive per your computers

instructions. The screw length should not exceed

30.5mm (measured from outside surface of side or

bottom of drive to tip of screw). Replace computer

cover and all outer screws.

Figure 6.Mounting Illustration

Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows

'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your

drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If

you prefer using DOS, download the DOS ATAPI driver from our web site.

Other Software - Additional software is required to use the SD-R1102 CD-R/-RW and DVD functions.

When you purchase the SD-R1102 as a kit, it will include the following software (Nero6):

•VOB InstantCD/DVD Software - used to create CDs

•CyberLink PowerDVD - used to view DVDs

USING THE DVD Combo Drive – SD-R1102

Drive Operation

Inserting a Disc - Horizontally

To insert a disc into a drive that is mounted horizontally, perform the following steps:

Figure 1.Inserting Disc

1. Open the drive's Loading tray by pressing the Eject Button.

2. Place disc or into drive's Loading tray

3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.

Inserting a Disc - Vertically

To insert a disc in a drive that is mounted vertically, perform the following steps:

1. Locate sliding disc holders (4 locations) on drive's Loading Tray.

2. The vertical position of the drive (eject button up or down) determines which of these four sliding

disc holders are used (see photo below). Position the disc behind 3 of the disc holders, two on

bottom, and one on upper rear, closest to drive). Using all four holders may cause the disc to not

set properly in tray.

3. Slide the disc holders towards the center of tray using your finger, opened paper clip or the end

of the emergency eject tool. The holder in the upper front side should be pulled away from the

center of tray.

4. Position the disc behind disc holders on upper and rear side of tray. Then put disc behind bottom front

holder

5. Check to see that all three disc holders are holding disc securely.

6. Close the drive by gently pushing in the tray or pressing the eject button.

Figure 2.Inserting Disc Vertically

Removing a Disc

To remove a disc from the Combo drive, perform the following steps:

1. Open the Loading Tray by pressing the Eject Button.

2. Slide disc holders away from disc.

3. Grasp disc by edges, and lift out of loading tray.

4. Press Eject Button again to close Loading Tray.

Software

When you purchase the SD-R1102 as a Kit, it will include Nero6 OEM Suite Software, which is used to

create CDs and view DVDs.

Usage Guidelines

•Keep the disc tray closed when not using the Combo Drive.

•Do not press down on the disc tray when opening or closing it.

•Do not place objects on the disc tray.

•Never use a damaged, broken, or deformed disc.

•Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc.

To stop a DVD movie, click Stop button in the DVD player application program.

NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the

disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed,

causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed

technology and do not indicate a problem with the drive.

Emergency Ejection

CAUTION: The following procedure is intended only as a last resort when pressing the

eject button fails to open the Loading Tray

1. Turn computer power OFF by properly shutting down system.

2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push in until loading tray

opens. Pull tray out.

Figure 3.Using Emergency Eject

Handling Media

DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD

movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-

related and can be remedied by proper handling and care of media.

Cleaning Media

Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc

accessing speed.

If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather

from the inner side outward.

Otros manuales para SD-R1102

Tabla de contenidos

Otros manuales de Unidad de DVD de Toshiba

Toshiba

Toshiba SD-R5272 Manual de usuario

Toshiba

Toshiba SD-M1502 Manual de usuario

Toshiba

Toshiba SD-C2712 Manual de usuario

Toshiba

Toshiba C2402 - SD - DVD-ROM Drive Manual de usuario

Toshiba

Toshiba SD-M1201 Manual de usuario

Toshiba

Toshiba SD-R1002 Manual de usuario

Toshiba

Toshiba SD-W1111 Manual del propietario

Toshiba

Toshiba SD-W1101 Manual de usuario

Toshiba

Toshiba SD-R1312 Manual de usuario

Toshiba

Toshiba SD-R2002 Manual de usuario

Toshiba

Toshiba SD-W1101 Instrucciones de montaje

Toshiba

Toshiba SD-R2612 Manual de usuario

Toshiba

Toshiba SD-R6112 Manual de usuario

Toshiba

Toshiba SD-C2512 Manual de usuario

Toshiba

Toshiba SD-M1802 Manual de usuario

Toshiba

Toshiba SD-R6112 Manual del propietario

Toshiba

Toshiba R6472 - DVD±RW Drive - IDE Manual de usuario

Toshiba

Toshiba SD-R6012 Manual de usuario

Toshiba

Toshiba PA3352 1CD2 Series Manual de usuario

Toshiba

Toshiba PA3454U-1DV2 - External USB 2.0 DVD Super Multi... Manual de usuario

Toshiba

Toshiba SD-R5112 Manual del propietario

Toshiba

Toshiba SD-M1201 Manual de usuario

Toshiba

Toshiba SD-M1401 Manual de usuario

Toshiba

Toshiba SD-R1612 Manual de usuario

Manuales populares de Unidad de DVD de otras marcas

Panasonic

Panasonic CFVDM732U - DVD Manual de usuario

LG GSA-4160B Manual de usuario

Panasonic

Panasonic VW-BN1 - DVD-RW / DVD-RAM Drive Manual de usuario

Sony

Sony DRU-500AX Manual de usuario

LG GSA-2164D Manual de usuario

Plextor

Plextor PX-755SA Manual de usuario

Pioneer

Pioneer BDC-TD03RS Manual del propietario

Samsung

Samsung SM-332B Manual de usuario

Freecom

Freecom MOBILE DVD RW II Manual de usuario

Plextor

Plextor PX-712 Manual de usuario

NEC

NEC ND-3550A Manual de usuario

Emprex

Emprex Slim Writer DVD R/RW USB 2.0 External Drive Manual de usuario

Philips

Philips PCA532K Manual de usuario

Sony

Sony AD-7740H Manual de usuario

Philips

Philips PCDV5016 Series Guía de referencia

Pioneer

Pioneer LaserMemory DVD-115 Manual de usuario

Samsung

Samsung SE-S224Q Manual de usuario

IBM

IBM 71P7285 Manual de usuario