Toshiba SD-M1612 Manual de usuario

TOSHIBA AMERICA INFORMATION SYSTEMS

STORAGE DEVICE DIVISION

IRVINE, CALIFORNIA

SD-M1612

DVD-ROM DRIVE

USER MANUAL

CONTENTS

Introduction..............................................................................1

Setup ........................................................................................3

Using the DVD-ROM Drive ......................................................6

Troubleshooting.......................................................................9

Specifications ........................................................................10

Drive Connectors...................................................................13

INTRODUCTION – SD-M1612 DVD-ROM Drive

General Features

Tray Loading Mechanism

3-way Disc Eject (eject button, software, emergency eject hole)

Average Random Access Time

CD-ROM 85ms

DVD 95ms

DVD-RAM 170ms

DAE (Digital Audio Extraction) Audio Capability

MPC3 Compatibility

Multi-Read Capability

Regionalization (RPC2 compliance) (DVD)

ATAPI BUS Interface:

Drive Speed

DVD 16X Single Layer

10X Dual Layer

CD 48X

DVD-RAM 2X (ver 1.0)

1X (ver 2.1)

Types of Disc Formats Supported

DVD

•DVD-ROM

DVD-5 - Single-sided/Single Layer

DVD-9 - Single-sided/Dual Layer

DVD-10 - Double-sided/Single Layer

DVD-18 - Double-sided/Dual Layer

•DVD-R, DVD-RW, DVD-RAM (Read)

•CD-DA

•CD+(E)G

•CD-MIDI

•CD-TEXT

•CD-ROM

•CD-ROM-XA

•CD-I Bridge (Photo-CD, Video CD)

•CD-I

•Multi-session (Photo-CD, CD Extra, CD-RW, CD-R)

•CD-R (Read)

•CD-RW (Read)

Front Panel

Figure 1.SD-M1612 DVD-ROM Drive Front Panel

Loading Tray

Load disc using tray.

Busy Indicator When you install a disc into the DVD-ROM drive, the BUSY light flashes slowly as it

attempts to locate the disc. One of the following will occur:

•BUSY light goes out. The DVD-ROM drive is ready to read data from the disc.

•BUSY light flashes slowly. The disc may be dirty.

•BUSY light remains ON. The DVD-ROM is accessing data.

•BUSY light remains ON indefinitely. The DVD-ROM is experiencing an error

Eject

Button

The Eject button is used to open the disc tray so you can install or remove a disc.

Emergency

Eject Hole

The emergency eject hole is to be used only when the Loading Tray will not open when

Eject button is pressed.

SETUP – SD-M1612 DVD-ROM

The following steps must be performed to properly install your drive:

•Set Drive Jumper Settings

•Connect Audio Cable (optional)

•Attach IDE BUS Cable

•Attach Power Cable

•Mount Drive

Jumper Settings

The mode select jumpers are 6 straight angle pins located on the rear of the DVD-ROM drive.

By placing a jumper on the pins, you can select the following functions:

Drive is configured using host interface signal CSEL

SL Configures drive as Slave

MA Configures drive as Master (default mode)

Figure 1.Mode Select Jumper

In most installations, jumper should remain in the MA position (factory default). It is recommended that

you install your DVD-ROM drive only on the secondary IDE BUS. If you are installing on primary IDE

BUS, your hard drive would then be the Master, and you should set your DVD-ROM drive to the Slave

position (SL)

Figure 2.Jumper Locations

Placing DVD-ROM Drive inside your Computer

Now that you have set the jumpers, you are ready to install your DVD-ROM drive inside your computer.

Important Note: Disconnect power from your computer system before beginning installation.

Remove computer cover and faceplate if required. Refer to your computer systems manual for removal

information. If the DVD-ROM drive is replacing a CD-ROM or DVD-ROM, remove drive presently

installed in your system.

Your Toshiba DVD-ROM drive can be placed in any free half-height drive slot at the front of your

computer. (It can be mounted horizontally or vertically.)

Carefully start sliding the DVD-ROM drive into the opening with the disc tray facing the front of the

computer. Before you push the drive all the way in you will need to connect the IDE BUS cable, Audio

cable and the Power cable on the back of the drive.

Connecting Cables

IDE BUS Cable (not supplied with drive) - Your computer system should have a primary and secondary

IDE BUS, cable with your Hard Drive most likely being the Master on the primary BUS. Connect BUS

cable as follows, assuring that pin 1 of cable (side with red stripe) is connected to pin 1 of the DVD-ROM

drive's interface connector:

If you are replacing your CD-ROM or DVD:

connect DVD-ROM drive to the BUS Cable connector

that the CD-ROM or DVD was connected to.

If DVD-ROM drive is not replacing a CD-ROM/DVD or is

an addition to a CD-ROM/DVD:

connect DVD-ROM drive to an open connector on the

secondary IDE BUS cable (not supplied with drive).

If DVD-ROM drive is to be slave on Primary BUS:

connect DVD-ROM drive to open connector on the

primary IDE BUS cable (not supplied with drive).

Figure 3.Installing BUS Cable

Power Cable - Connect an internal computer power

supply cable to the power socket at the back of the

DVD-ROM drive. One side of the plug has chamfered

edges, so the power connector fits only one way. Push

plug completely into the socket making sure the plug fits

correctly.

Figure 4.Installing Power Cable

Audio Cable (optional) - If you have a sound card and

speakers, and would like to play audio CDs on your

computer, you will need to install a CD/DVD audio cable.

Toshiba's DVD-ROM drives use a standard 4-pin audio

cable that can be purchased from most local computer

suppliers. The sound cable connects to your sound card

at one end and the other end connects to the digital

audio connector at the left rear of the DVD-ROM drive

(see DVD-ROM drive Back Panel photo for location).

Refer to the instructions that came with your sound card

for details on any sound-driver software required.

Figure 5.Installing Audio Cable

Completing Installation

After you have connected all the necessary cables,

push the DVD-ROM drive completely into the

computers drive slot. Mount drive per your computers

instructions. The screw length should not exceed

30.5mm (measured from outside surface of side or

bottom of drive to tip of screw). Replace computer

cover and all outer screws.

Figure 6.Mounting Illustration

Software Driver - Toshiba's optical drives do not require any unique device drivers for Windows

'95/'98/2000/Me/XP/NT. After installing your drive and re-booting, your system should recognize your

drive. Windows '95/'98/2000/Me/XP/NT Operating Systems support all Toshiba optical drives natively If

you prefer using DOS, download the DOS ATAPI driver from our web site.

USING THE DVD DVD-ROM Drive – SD-M1612

Drive Operation

Inserting a Disc - Horizontally

To insert a disc into a drive that is mounted horizontally, perform the following steps:

Figure 1.Inserting Disc

1. Open the drive's Loading tray by pressing the Eject Button.

2. Place disc into drive's Loading tray

3. Press Eject button again or gently push on the open disc tray. Tray will automatically close.

Inserting a Disc - Vertically

To insert a disc in a drive that is mounted vertically, perform the following steps:

1. Locate sliding disc holders (4 locations) on drive's Loading Tray.

2. Position the disc behind the disc holders

3. Close the drive by gently pushing in the tray or pressing the eject button.

Figure 2.Inserting Disc Vertically

Removing a Disc

To remove a disc from the DVD-ROM drive, perform the following steps:

1. Open the Loading Tray by pressing the Eject Button.

2. Grasp disc by edges, and lift out of loading tray.

3. Press Eject Button again to close Loading Tray.

Usage Guidelines

•Keep the disc tray closed when not using the DVD-ROM Drive.

•Do not press down on the disc tray when opening or closing it.

•Do not place objects on the disc tray.

•Never use a damaged, broken, or deformed disc.

•Do not press the Open/Close button while the drive is playing a DVD movie or accessing a disc.

To stop a DVD movie, click Stop button in the DVD player application program.

NOTE: High-speed drives spin the disc at a high rotational speed. If a disc has printing on only half of the

disc, or if there is a slight imbalance in the disc, the imbalance is greatly magnified by the high speed,

causing the drive to vibrate or produce a fan-like noise. These effects are inherent in the high-speed

technology and do not indicate a problem with the drive.

Emergency Ejection

CAUTION: The following procedure is intended only as a last resort when pressing the

eject button fails to open the Loading Tray

1. Turn computer power OFF by properly shutting down system.

2. Insert a solid bar (i.e. large paper clip) into Emergency Eject hole and push as shown in the

picture below

3. DVD tray will open/eject.

Figure 3.Using Emergency Eject

This procedure cannot be repeated without cycling the DVD-ROMs (computer's) power.

After the media is removed and the loading tray is closed, the tray will not reopen without first turning the

power ON/OFF.

NOTE: Use a bar that is less than 1.5 mm in diameter.

Do not insert more than 50mm in depth.

Inserting more than 50mm may damage the DVD-ROM drive.

Handling Media

DVD media is sensitive to dust and fingerprints. Carefully handle media by its edges only. If a DVD

movie skips or hangs during playback, clean the media. Most DVD video playback issues are media-

related and can be remedied by proper handling and care of media.

Cleaning Media

Try to avoid touching the read area (underside) of the disc as dirt and smears will degrade the disc

accessing speed.

If the disc becomes dirty wipe it with a damp soft cloth. Avoid cleaning in a circular motion, but rather

from the inner side outward.

Tabla de contenidos

Otros manuales de Unidad de DVD de Toshiba

Toshiba

Toshiba SD-M1802 Manual de usuario

Toshiba

Toshiba SD-R5372 Manual de usuario

Toshiba

Toshiba SD-R1002 Manual de usuario

Toshiba

Toshiba SD-M1912 Manual de usuario

Toshiba

Toshiba SD-W1101 Manual de usuario

Toshiba

Toshiba SD-R5372V Manual de usuario

Toshiba

Toshiba PA3454U-1DV2 - External USB 2.0 DVD Super Multi... Manual de usuario

Toshiba

Toshiba SD-W1101 Instrucciones de montaje

Toshiba

Toshiba SD-C2732 Manual de usuario

Toshiba

Toshiba SD-M1201 Manual de usuario

Toshiba

Toshiba SD-R6372 Manual de usuario

Toshiba

Toshiba H802A - SD - Disk Drive Hoja de especificaciones

Toshiba

Toshiba SD-R2002 Manual de usuario

Toshiba

Toshiba C2402 - SD - DVD-ROM Drive Manual de usuario

Toshiba

Toshiba SD-R1202 Manual de usuario

Toshiba

Toshiba SD-R1202 Manual de usuario

Toshiba

Toshiba SD-W1111 Manual del propietario

Toshiba

Toshiba SD-R2312 Manual de usuario

Toshiba

Toshiba SD-R5112 Manual de usuario

Toshiba

Toshiba SD-M1302 Manual de usuario

Toshiba

Toshiba SD-R2612 Manual de usuario

Toshiba

Toshiba SD-R6572M Manual de usuario

Toshiba

Toshiba SD-M2012C Manual de usuario

Toshiba

Toshiba SD-R5002 Manual de usuario

Manuales populares de Unidad de DVD de otras marcas

Panasonic

Panasonic CFVDM732U - DVD Manual de usuario

LG GSA-4160B Manual de usuario

Panasonic

Panasonic VW-BN1 - DVD-RW / DVD-RAM Drive Manual de usuario

Sony

Sony DRU-500AX Manual de usuario

LG GSA-2164D Manual de usuario

Plextor

Plextor PX-755SA Manual de usuario

Pioneer

Pioneer BDC-TD03RS Manual del propietario

Samsung

Samsung SM-332B Manual de usuario

Freecom

Freecom MOBILE DVD RW II Manual de usuario

Plextor

Plextor PX-712 Manual de usuario

NEC

NEC ND-3550A Manual de usuario

Emprex

Emprex Slim Writer DVD R/RW USB 2.0 External Drive Manual de usuario

Philips

Philips PCA532K Manual de usuario

Sony

Sony AD-7740H Manual de usuario

Philips

Philips PCDV5016 Series Guía de referencia

Pioneer

Pioneer LaserMemory DVD-115 Manual de usuario

Samsung

Samsung SE-S224Q Manual de usuario

IBM

IBM 71P7285 Manual de usuario