Toshiba 3560 Manual de usuario

SERVICE MANUAL

PLAIN PAPER COPIER

3560/70

Click the Page Only button to close the overview area of the window.

Click the Bookmarks and Page button to open the Contents and

display bookmarks created for the document. Click a bookmark’s name

to go to the Page marked by that bookmark.

Click the Thumbnails and Page button to open the overview area and

display thumbnail images of each document page. Click a thumbnail to

go to the page marked by that thumbnail.

GENERAL PRECAUTIONS REGARDING THE INSTALLATION

AND SERVICE FOR THE COPIER 3560/70

The installation and service should be done by a qualified service technician.

1. Transportation/Installation

• When transporting/installing the copier, use two persons and be sure to use the positions as indi-

cated below.

The copier is fairly heavy and weighs approximately A kg (B lb), therefore pay full attention when

handling it.

4 portions

3560

161

3570

203

2. Installation

• Be sure to use a dedicated outlet withAC 115V/15A(220V, 230V, 240V/10A) or more for its power

source.

• The copier must be grounded for safety.

Never ground it to a gas pipe or a water pipe.

• Select a suitable place for installation.

Avoid excessive heat, high humidity, dust, vibration and direct sunlight.

• Also provide proper ventilation as the copier emits a slight amount of ozone.

• To insure adequate working space for the copying operation, keep a minimum clearance of 80 cm

(32”) on the left, 80 cm (32”) on the right and 10 cm (4”) in the rear.

• After having installed the copier, be sure to push the carrying handles into the copier and fasten

them with screws.

3. Service of Machines

• Basically, be sure to turn the main switch off and unplug the power cord during service.

• Be sure not to touch high-temperature sections such as the exposure lamp, the fuser unit, the

damp heater and their periphery.

• Be sure not to touch high-voltage sections such as the chargers and the high-voltage transformer.

• Be sure not to touch rotating/operating sections such as gears, belts, pulleys, etc.

• When servicing the machines with the main switch turned on, be sure not to touch live sections

such as the lamp terminal, etc. and rotating/operating sections.

• Use suitable measuring instruments and tools.

4. Main Service Parts for Safety

• The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important

for safety. Be sure to handle/install them properly.

5. Cautionary Labels

• During service be sure to check the rating plate and the cautionary labels such as “Unplug the

power cord during service”, “Hot area” etc. to see if there is any dirt on their surface or whether

they are properly stuck to the copier.

6. Disposition of Consumable Parts/Packing Materials

• Regarding the recovery and disposal of the copier, supplies, consumable parts and packing mate-

rials, it is recommended to follow the relevant local regulations or rules.

7. When parts are disassembled, reassembly is basically the reverse of disassembly unless

otherwise noted in this manual or other related documents. Be careful not to reassemble

small parts such as screws, washers, pins, E-rings, toothed washers in the wrong places.

8. Basically, the machine should not be operated with any parts removed or disassembled.

9. Precautions Against Static Electricity

• The PC board must be stored in an anti-electrostatic bag and handled carefully using a wristband,

because the ICs on it may become damaged due to static electricity.

Caution:Before using the wrist band, pull out the power cord plug of the copier and make sure

that there is no uninsulated charged objects in the vicinity.

Nov. 1997 © TOSHIBA 1 - 1 3560/70 SPECIFICATIONS

Copy paper

Cassette Duplexing Manual Note

Size A3~A5-R A3~A6-R Adjustable to

(Ledger~Statement-R) Unfixed, Arbitary sizes

Thickness 64~80 64~130 Unit: g/m2

(Weight) (17~22) (17~34) (Unit: lb.)

Special _ _ OHP film

paper etc.

Copy process Indirect electrophotographic process (dry)

Type Desk top (console when the pedestal is used)

Exposure Type Slit exposure with fixed table

Acceptable originals Kind Sheets, books, and 3-dimensional objects.

When the document feeder is used:

Sheet originals only (60 g/m2~90 g/m2) (16 lb.~24 lb.)

Maximum size A3 (Ledger)

1. SPECIFICATIONS • ACCESSORIES • OPTIONS • SUPPLIES

1.1 Specifications

3560/70 SPECIFICATIONS 1 - 2 Nov. 1997 © TOSHIBA

Copy speed

System copy speed

(BLI format)

First copy Approx. 4.0 sec. (Actual-size A4 or Letter from large capacity feeder)

Warm-up time Approx. 80 sec.

Multiple copying 1~999, keyboard entry

Reproduction ratio

Actual ratio 100% or 101% (Setting mode)

Zoom ratios 50~200% (Multiple reduction and enlargement in 1% steps)

Manual feeding represents the value when the size is set.

CPM

Cassette/manual LCF

Paper size 3560 3570 3560 3570

A4, B5, A5-R 35 35 35 35

LT, ST-R

A4-R, B5-R 26 26 — —

LT-R

B4, FOLIO 22 22 — —

LG, Computer

A3 19 19 — —

Reduction/ 15 15 15 15

Enlargement

Mode CPM

Original→Copy Number of copies 3560/70

1 → 11 set 30

3 set 33

5 set 34

1 → 21 set 10

3 set 19

5 set 24

2 → 21 set 8

3 set 17

5 set 21

2 → 11 set 16

3 set 25

5 set 29

*Ten originals (A4) are set in the RADF. This in-

cludes the first copy time.

Nov. 1997 © TOSHIBA 1 - 3 3560/70 SPECIFICATIONS

598mm

640mm

540mm

601mm

661mm

540mm

Paper supply Cassette or sheet-bypass feeding

Cassette: 600 sheets

Sheet-bypass feeding: 50 sheets

Toner supply Automatic density detection and replenishment

Toner cartridge replacement

Exposure Automatic control and manually selectable (9 steps)

Weight Copier:*173 or*292 kg(with 2cassettes andthe platencover),

*1: 3560, *2: 3570 ADU: 10 kg

Power source 115 V ~ 60 Hz, 12A For the U.S.A. and Canada

220–240 V ~ 50/60 Hz, 8A For Europe

Power consumption 1.5 kW (115 V), 1.7 kW (220 V/240 V)

Counter 7-digit total counter

Machine size

3560/70 SPECIFICATIONS 1 - 4 Nov. 1997 © TOSHIBA

1.2 Accessories

Copy receiving tray : 1 pc.

Operator’s manual : 1 pc.

Set-up report : 1 pc.

Drum : 1 pc.

Developer : 1 bottle

Toner : 1 pc.

*Accessories vary according to the destination.

1.3 Options

Automatic duplexing unit: ADU MD-5002A

Automatic document feeder: ADF MR-3006A (RADF), MR-2008 (ADF)

Paper feed pedestal: PFP KD-1003 (1 cassette), KD-2009 (2 cassettes)

Paper feed unit MY-1006

Large capacity feeder: LCF MP-1501LT, MP-1501A4, MP-4001LT, MP-4001A4

Sorter MG-1003B (10 bins), MG-2012 (20 bins)

MG-1004A (10 bins staple)

MG-2009A (20 bins)

MG-2010 (20 bins staple)

Key copy counter MU-8/MU-10 (6 digit)

1.4 Supplies

Drum OD-3560

Developer ZD-3560

Toner ZT-3560, 3560E

*Options vary according to the destination.

Nov. 1997 © TOSHIBA 2 - 1 3560/70 GENERAL

2. OUTLINE OF THE MACHINE

2.1 Sectional Views and Electrical Parts Location Diagram

2.1.1 Sectional view

[A] Front view

(This diagram includes an installed ADU.)

ENEM

EP ER

AO AP AN

AR BK AL

CN CO

CQ DMFN

3560/70 GENERAL 2 - 2 Nov. 1997 © TOSHIBA

No. Name

CQ Cassette

CR Manual feed separation pad

CS Manual feed roller

DT Manual pickup roller

DK Cassette separation roller

DL Cassette feed roller

DM Cassette pickup roller

DN Upper transport roller

DO Manual feed switch (S6)

DP Paper guide

DQ Lower transport roller

DR Aligning switch (S8)

DS Aligning roller (U)

ET Aligning roller (L)

EK Thermistor-1 (THMS1)

EL Thermostat (THERMO)

EM Heater lamp

EN Heat roller (upper side)

EO Pressure roller (lower side)

EP Separation claw (for heat roller)

EQ Felt roller

ER Heat roller cleaning blade

ES Fuser exit roller

FT Scraper

FK Fuser cover

FL Paper stop switch-1 (S7)

FM Paper stop switch-2 (S16)

FN Paper-empty switch-2 (S14)

FO Cassette tray

FP Cassette size switch-2 (S15)

FQ Exit/ADU selection gate

FR Exit roller

FS ADU (option)

GT Exit fan (M7)

GK Bottom fan (M8)

No. Name

1Carriage 1

2Mirror 1

3Reflector

4Light distribution adjustment plates

5Exposure lamp

6Carriage 2

7Mirror 2

8Mirror 3

9Mirror unit

AT Mirror 4

AK Mirror 5

AL Mirror 6

AM Slit glass

AN Auto exposure sensor

AO Lens

AP Original glass

AQ Ozone filter

AR Main charger

AS Discharge lamp

BT Receiving tray

BK LED eraser array

BL Main blade

BM Recovery blade

BN Toner recovery auger

BO Separation claw (for drum)

BP Transfer charger

BQ Separation charger

BR Drum

BS Bias guide

CT Transport belt

CK Magnetic roller

CL Leveller (doctor)

CM Auto-toner sensor

CN Mixer 1

CO Mixer 2

CP Sheet bypass guide

Nov. 1997 © TOSHIBA 2 - 3 3560/70 GENERAL

[B] Rear side view

FRES

HLGRHKHTHRITIK

HP HO IO IP

GQ IQ

Otros manuales para 3560

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Copiador de Toshiba

Toshiba

Toshiba e-studio550 Manual de usuario

Toshiba

Toshiba e-Studio 350 Manual de usuario

Toshiba

Toshiba e-STUDIO 203S Manual de usuario

Toshiba

Toshiba e-STUDIO 4511 Manual de usuario

Toshiba

Toshiba 2060 Manual de usuario

Toshiba

Toshiba DP4500 Cómo utilizar

Toshiba

Toshiba 1360 Manual de usuario

Toshiba

Toshiba e-studio 45 Manual de usuario

Toshiba

Toshiba e-studio 900 Manual de usuario

Toshiba

Toshiba e-studio120 Manual de usuario

Toshiba

Toshiba e-STUDIO 55 Manual de usuario

Toshiba

Toshiba e-studio 211c Manual de usuario

Toshiba

Toshiba FC15 Manual de usuario

Toshiba

Toshiba 60th Series Manual de usuario

Toshiba

Toshiba 1550 Manual de usuario

Toshiba

Toshiba 4550 Manual de usuario

Toshiba

Toshiba e-STUDIO 550 Instrucciones de instalación

Toshiba

Toshiba DP1600 Cómo utilizar

Toshiba

Toshiba e-studio 12 Manual de usuario

Toshiba

Toshiba MY-1015 Manual de usuario

Toshiba

Toshiba KD1009 Manual de usuario

Toshiba

Toshiba E-studio 281c Manual de lista de piezas

Toshiba

Toshiba 2460 Cómo utilizar

Toshiba

Toshiba e-studio 120 Manual de usuario

Manuales populares de Copiador de otras marcas

Canon

Canon iR1210 Manual de referencia

Ricoh

Ricoh FW740 Manual de usuario

Minolta

Minolta CF910 Manual de usuario

Ricoh

Ricoh B003 Manual de usuario

Xerox

Xerox EC70 Manual de usuario

Oce

Oce 9800 Manual de usuario

Olivetti

Olivetti d-Copia 1800 Manual de usuario

Minolta

Minolta Di181 Manual de usuario

Canon

Canon iR5000i Manual de usuario

Telecrane

Telecrane F25 Manual de usuario

Xerox

Xerox WorkCentre Pro 40 Manual de usuario

Canon

Canon NP6317 Cómo utilizar

Sharp

Sharp AR-5015 N Manual de usuario

Ricoh

Ricoh Di-C1 Manual de usuario

Mita

Mita MIP-2400 Manual

Sharp

Sharp AL-2061 Manual de usuario

Muratec

Muratec MFX-C2280 Manual de usuario

Ricoh

Ricoh FT5034C Manual de usuario