Toshiba JOKC1 Manual de usuario

Operator interface station

Keyboard controller JOKC1

Operator′s keyboard UOPK8UE

6F8C0808

Toshiba Integrated Control System

Fourth Edition January, 2005

The contents of this manual may be revised without notice.

No part of this manual may be reproduced in any form without permission.

Safety Precautions

OIS-DS52 and the instruction manual give important information for using products

safely. It helps prevent damage to properties and hazard to people who use them or to

others.

Make yourself familiar with the signal words and signs in this page then read the

safety precautions that follow and always follow the instructions to avoid hazards.

Explanation of signal words

Signal word is a word that designates a degree or level of hazard seriousness.

The words WARNING and CAUTION are used for the products.

WARNING Indicates a potentially hazardous situation which could result in death or

serious injury, if you do not follow the instructions.

CAUTION Indicates a potentially hazardous situation which may result in minor or

moderate injury and/orproperty damage, if you do not follow the instructions.

Hazard alert shapes and symbols

Following shapes and symbols are used in the safety precaution labels affixed to the

products and in other places including operation manuals for giving safety instructions.

Filled circle means "Mandatory Action" or "Do as indicated."

Required action is shown in the circle or described near the circle.

Circle band with a diagonal slash means "Prohibition" or " You must not do."

Prohibited action is shown in the circle or described near the circle.

Triangle means "Hazard Alerting" or "Be alert against hazard."

The kind of hazard is shown in the triangle or described near the triangle.

Exclamation point with a triangle is a safety alert symbol which indicates a potential hazard.

It is used with a Signal Word.

Square or rectangle means "Information Messages" or "Notice."

•Make sure to observe the following points.

WARNING

System fault or data loss may occur, if the power fails or the power system (including

the power switch) is turned off. Toshiba cannot assure any compensation for the

resulting damages. Take precautions in advance to protect the system in order to

prevent such event to take place. Also back up your data regularly to minimize the

possible damage by loss of data as a result of such event.

Safety Precautions

•Some points about peripherals

Regarding peripheral equipment, read the instruction manuals accompanying the

devices and follow the instructions. Even similar warnings and precautions may be

indicated in different ways; please be careful not be confused by them.

1. Safety Precautions for Installation

WARNING

Grounding required:

To avoid the risk of electric shock or fire, be sure to ground the equipment.

CAUTION

Choose proper environment for installation:

Avoid grounding and storing the equipment in the following environments:

•Location with considerable dust

•Location in which flammable or corrosive gases (such as SO2and H2S) are present

•Location where vibration or shock exceeds allowable limits

•Location where condensation may occur due to rapid change in temperature

•Location where the temperature is not within the specified range for installation

•Location where the humidity exceeds the specified limits for installation

•Location in the direct sunlight

•Location near a device that generates strong radio waves or magnetic fields

Considerations for maintenance and inspection:

Install the equipment in a place that facilitates maintenance and inspection. If not, in case

of malfunctioning, it may hinder the recovery of the system and result in serious accident.

Ensure proper ventilation:

Do not block vents, intake or exhaust openings of the equipment. Blocking them may cause

malfunctioning or overheating which may result in fire.

Ensure correct cabling:

Correctly connect the accompanying cables to the JOKC1 card and keyboard UOPK8UE

connectors. Incorrect connection may result in damaging the equipment.

Avoid noise interference:

Place I/O signal and data transmission signal cables away from the power cables and the

devices that generate magnetic or electric fields. Otherwise, interference noise may cause

the equipment to malfunction or fail.

Safety Precautions

iii

2. Safety Precautions for Inspection and Maintenance

WARNING

Turn off power:

Before attaching or detaching the JOKC1 card or keyboard UOPK8UE or connecting the

equipment, make sure to turn off the power. Failure to do so may result in electric shock or

equipment fault.

CAUTION

Avoid shock:

Do not drop, bump or give strong shocks to the JOKC1 card or the keyboard UOPK8UE.

Shocks may cause malfunction.

Discharge static electricity:

Before touching the JOKC card or the keyboard UOPK8UE, discharge static electricity

from your body by touching a metal that is grounded. Static electricity may cause

equipment to malfunction or fail.

Use a conductive mat or bag to avoid static:

When the JOKC1 card is removed from the OIS PC, it should be placed on a conductive

bag (containing reserve cards, etc.) or on a static proof mat, which is put on a grounded

work bench. Static electricity may damage electrical parts.

Wipe off dirt:

Wipe off dirt and dust from the JOKC1 card and the keyboard UOPK8UE, using a soft cloth.

If the dirt is persistent, wet a cloth, wring it dry and then use it on the dirt. Dirt on the parts

may result in faulty actions and operations.

Do not use paint thinner for cleaning:

Do not use benzine or paint thinner for cleaning the JOKC1 card or the keyboard

UOPK8UE. These chemicals will distort or discolor the JOKC1 card or the keyboard

UOPK8UE.

Safety Precautions

3. Safety Precautions for Daily Use

WARNING

Check specifications:

Before using the equipment, make sure that the capacity, voltage and regulation of the

power supply meet the specifications of the equipment. In case they don not, the

equipment may not only work adequately but maysuffer a breakdown or overheat that may

result in fire.

Turn off power in the event of a problem:

If the temperature in or around the equipment rises abnormally high or an unusual fault

occurs to the equipment, stop using the equipment and turn off its power and then contact

your Toshiba representative. If the equipment is left alone, overheat may result in fire.

CAUTION

Remove static electricity first:

When installing/removing the JOKC1 card onto/from the OIS PC, make sure to remove the

static electricity first. Unremoved static electricity may cause equipment failure or data

damage.

Do not touch components:

Do not touch the JOKC1 card parts, pins, connectors or soldered surfaces with any part of

your body. Static electricity may damage IC's or LSI's, and cause equipment to fail. This

may also result in damaging the pointed end of the component lead.

Do not disassemble the equipment:

Do not disassemble or modify the JOKC1 card or the keyboard UOPK8UE. Doing so may

not only lessen equipment safety but also may result in equipment malfunction or failure.

Handle cords and cables properly:

Do not force to pull, twist or bend cords and cables of power supply. Otherwise cables may

break or become overheated.

Keep off metals:

Do not insert metals or drop clips, etc. into any openings in the main unit of the equipment.

Doing so may cause fire.

Remove the power cord before work:

Before starting the work, turn off the power switch and the AC input switch and then remove

the power cord plug. Negligence to do so may cause electric shock or failure.

Safety Precautions

Application Restriction

 This product is not meant for use in systems which include (note 1) equipment that

directly affects human life. Therefore it is not meant to be used for that purpose.

 If this product is to be used for systems including (note 2) equipment that is a part of

people′s safety, and has a great affect on the functional support of the public, please

consult with our sales counter, since (note 3) special consideration is needed concerning

the system application, maintenance, and control.

(Note 1)Equipment that directly affects human life includes the following:

•Medical instruments, such as life support equipment, and instruments used in

an operating room.

(Note 2)Systems which includes equipment that takes part in people's safety, and has

great influence on functional support of public includes the following:

•A main control system for a nuclear power plant, a safetyprotection system for

nuclear power facilities, and other important system for safety purpose.

•Operation control system for mass transportation and air traffic control system.

(Note 3)Special consideration means to construct safe system (fool proof design, fail

safe design, a tedious design) upon much discussion with our engineer.

Exemption Matters from Responsibility

 We are not responsible for any damage caused by fire, earthquakes, actions by a third

party, other accidents, any intentional or unintentional misuse, or any use under

abnormal conditions.

 We are not responsible for any damage (loss of business profit, interruption of business,

or change or loss of memory content) related to the use or inability to use this product.

 We are not responsible for any damage caused due to ignorance of the contents on the

handling manual.

 We are not responsible for any damage caused by misoperation when the purchaser

combines an application program created by the purchaser with any of our programs.

Safety Precautions

Introduction

vii

Introduction

This manual describes the procedure for incorporating Toshiba's software, keyboard

controller JOKC1 and operator’s keyboard UOPK8UE into your personal computer to

construct the operator interface station OIS-DS for Toshiba's integrated control system

TOSDIC-CIE DS.

Introduction

viii

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Sistema de control de Toshiba

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba BMS-CT1280E Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba TOSVERT VF-PS1 Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba Carrier BMS-SM1280HTLUL Manual de usuario

Toshiba

Toshiba OIS Series Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba BMS-SM1280HTLE Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba BMS-SM1280HTLE Manual de usuario

Toshiba

Toshiba BMS-SM1280HTLE Manual de usuario

Toshiba

Toshiba Combi control Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual del propietario

Toshiba

Toshiba BMS-TP5121PWE Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Toshiba

Toshiba Carrier BMS-SM1280HTLUL Manual de usuario

Toshiba

Toshiba TOSDIC-CIE DS Manual de lista de piezas

Toshiba

Toshiba TOSDIC-CIE DS Manual de usuario

Manuales populares de Sistema de control de otras marcas

Pentair Pool Products

Pentair Pool Products Compool Manual de usuario

ComfortNET

ComfortNET CTK04 Manual de usuario

Fireye

Fireye InSight II 95DSS3 Manual de usuario

CAME

CAME G3000 Manual de usuario

Idemia

Idemia MorphoAccess VP MD Manual de usuario

Axis

Axis P1445-LE-3 Manual de usuario

HEIDENHAIN

HEIDENHAIN TNC 150 B Manual de usuario

CNC-Step

CNC-Step High-Z T-Series Manual de usuario

Doosan

Doosan DVF Series Manual de usuario

Honeywell

Honeywell KAP 140 Manual de usuario

Honeywell

Honeywell vk41 series Manual de usuario

AirBench

AirBench FPW Guía de instalación

Cypress

Cypress HHR-3160 Manual de usuario

CAME

CAME GLT40AOS Manual de usuario

Zonex

Zonex GEN II -VVT Guía del usuario

Altronics

Altronics K 9650 Manual de usuario

micro-trak

micro-trak RoadMaster Manual de usuario

micro-trak

micro-trak Calc-An-Acre II Manual de usuario