Toshiba B-EX4 SERIES Instrucciones de funcionamiento y mantenimiento

E-1

Quick Installation Manual

This manual is a quick guide on how to set up your B-EX4 printer.

For more details please download the latest edition of the owner’s

manual from the following website.

http://barcode.toshibatec.co.jp/eng/manual/b-ex/index.htm

Important Information to the User

In order to meet Product Safety, FCC and CE marking requirements, it is

advised to use the power cord which was shipped with this product. Otherwise

this cable needs to meet the following standards.

Power Cord

For this product a UL listed, detachable power cord is required. Outside the US,

power cords need to meet the particular country’s certification and application

requirements. If a different power cord is used from that described above you

might violate safety certifications which are in force in the country of use. The

socket-outlet needs to be installed near the equipment and must be easily

accessible.

TOSHIBA BARCODE

PRINTER

B-EX Type 2 Series

!00TSCC0236001!

E-2

1. Unpacking

Unpack the printer as per the Unpacking Instructions supplied with the printer.

1.1 Accessories

When unpacking the printer, please make sure all the following accessories are supplied with the

printer.

CD-ROM (1 pc.)

Safety precautions Quick installation manual Power cord

2. Printer overview

2.1 Appearance

2.1.1 Front View

2.1.2 Rear View

NOTES:

1. Check for damages or scratches on the printer. However, please note that TOSHIBA TEC shall have no

liability for any damage of any kind sustained during transportation of the product.

2. Keep the carton and internal packaging for future transportation of the printer.

•

Bar code printer application (BarTender Ultra Lite)

•

Windows Driver

•

Owner's Manual

•

Specifications (Programming, Key operation, etc.)

•

Product information (Catalogue)

LCD Message Display

Operation Panel

Top Cover

Supply Window

Media Outlet

Reserved for Parallel

interface

Reserved for Serial or

WLAN interface

USB interface

LAN interface

Reserved for Expansion

I/O interface

Power Switch

AC Power Inlet

Reserved for

RTC & USB

host interface

E-3

CAUTION!

1. Be careful not to touch the Print Head Element when raising the Print Head Block. Failure to

do this may cause missing dots by static electricity or other print quality problems.

2. When loading or replacing the media or a ribbon, be careful not to damage the print head with

a hard object like a watch or a ring.

Since the print head element can be easily damaged by shock, please treat it carefully and do

not hit it with any hard object.

3. Loading the Supplies

3.1 Loading the Media

The following procedure shows the steps to properly load the media into the printer so that it feeds

straight and true through the printer.

The printer prints both labels and tags.

1. Turn the Head Lever to Free position, then release the Ribbon Shaft Holder Plate.

2. Open the Print Head Block.

1. Do not touch any moving parts. To reduce the risk of fingers, jewellery, clothing, etc., being

drawn into the moving parts, be sure to load the media once the printer has stopped moving

completely.

2. The Print Head becomes hot immediately after printing. Allow it to cool before loading the

media.

3. To avoid injury, be careful not to trap your fingers while opening or closing the cover.

Care must be taken not to allow

the metal or glass part of a watch

to touch the print head edge.

Care must be taken not to allow a

metal object like a ring to touch

the print head edge.

Print Head Block

TAG

LABEL

FREE

Head Lever

Top Cover

NOTES:

Precautions for use of supplies

The max print speed ensuring the print quality differs depending on the combination of media and ribbon.

Please change the print tone or print energy setting according to the media or ribbon to be used.

Especially when printing serial bar codes, the bar-to-space ratio needs to be changed depending on the print

speed.

For details, please refer to the Supply Sp

ecification.

Ribbon Shaft Holder Plate

E-4

3. Push the Paper guide R to the right or in horizontal movement.

4. Put the media on the Paper Holder.

5. Pass the media around the Paper Holder, and then pull the media towards the front of the

printer.

6. Push the Paper Guide against the media until the media is held firmly in place. To lock the

Media, shift the Paper Guide R to vertical position.

7. Place the media between the Media Guides, adjust the Media Guides to the media width, and

shift the Paper Guide R to vertical position to tighten.

NOTES:

1. When the Head Lever is turned to FREE position, the Print Head is raised.

2. To enable printing the Head Lever must be set to the LABEL / TAG position. (This ensures that the

Print Head is closed.)

There are two head pressure levels in the LABEL / TAG position. Set the Head Lever depending on the

media type:

Position LABEL: Labels

Position TAG: Tags

However, proper position may differ depending on media. For details, refer to your TOSHIBA TEC

authorised service representative.

In the case of labels rolled with

the print side facing inside.

In the case of labels rolled with

the print side facing outside.

Paper Guide R

Paper Guide L

E-5

8. Check that the media path through the printer is straight. The media should be centered under

the Print Head.

9. Lower the Print Head Block until it stops.





Batch mode

In the batch mode, the media is continuously printed and fed until the numbers of labels/tags

specified in the issue command have been printed.





Loading with peel off module

When the optional Peel-off Module is fitted, the backing paper is automatically removed from the

label at the Strip Plate as each label is printed.

(1) Remove enough labels from the leading edge of the media to leave 500mm of backing paper

free.

(2) Insert the backing paper under the Strip Plate.

(3) Wind the backing paper onto the Take-up Spool and fix it in position with the Take-up Clip.

(Wind the paper counterclockwise around the spool as this is the direction it rotates.)

(4) Rotate the Take-up Spool counter-clockwise a few times to remove any slack in the backing

paper.

(5) Set the Selection Switch mounted on the Rewinder Assembly to STANDARD/PEEL OFF

position.

Backing Paper

Strip Plate

Take

up Spool

Take

up Clip

Paper Guide

Media Guide

Print Head

Media

Media Guide

Locking Screw

E-6

Media Outlet

Cutter Module





Loading with cutter

When the optional Cutter Module is fitted, the

media is automatically cut. A disc cutter is

available as an option. Insert the leading edge

of the media into the cutter until it comes out

the Media Outlet of the Cutter Module.

3.2 Loading the Ribbon

There are two types of media available for printing on: these are thermal transfer media and direct

thermal media (a chemically treated surface). DO NOT LOAD a ribbon when using a direct thermal

media.

1. Grasp the tabs on the top and bottom of the Ribbon Stoppers and move the Ribbon Stoppers

back to the end of the Ribbon Shaft.

NOTES:

1. When attaching the ribbon stoppers, make sure that the pinchers face into the printer.

2. Be sure to remove any slack in the ribbon when printing. Printing with a wrinkled ribbon will lower the

print quality.

3. The Ribbon Sensor is mounted on the rear of the Print Head Block to detect a ribbon end. When a ribbon

end is detected, “NO RIBBON” message will appear on the display and the ERROR LED will illuminate.

WARNING!

The cutter is sharp, so care must be taken not to injure yourself when handling the cutter.

CAUTION!

1. Be sure to cut the backing paper of the label. Cutting labels will cause the glue to stick to the

cutter which may affect the cutter quality and shorten the cutter life.

2. Use of tag paper when the thickness exceeds the specified value may affect the cutter life.

NOTES:

1. Be sure to set the Selection Switch to STANDARD/PEEL OFF position.

2. The backing paper is easier to feed back to the Take-Up Spool if the Front Plate is removed.

3. Fit the Take-Up Clip so that the longer side of the clip is fitted into the shallow groove in the Take-Up

Spool.

4. The backing paper can be wound directly onto the Take-up Spool or a paper core.

Ribbon Stopper

Ribbon Shaft

E-7

2. Leaving plenty of slack between the ribbon spools, place the ribbon onto the Ribbon Shafts as

shown below. There are 2 possible ways to load the ribbon.

3. Slide the Ribbon Stoppers along the Ribbon Shafts to a position where the ribbon is centred

when fitted.

4. Lower the Print Head Block and set the Ribbon Shaft Holder Plate aligning its holes with the

Ribbon Shafts.

5. Take up any slack in the ribbon. Wind the leading tape onto the ribbon take-up roll until the ink

ribbon can be seen from the front of the printer.

6. Turn the Head Lever to Lock position to close the Print Head.

7. Close the Top Cover.

Print Head Block

Ribbon Shaft

Holder Plate

Ribbon Shaft

Outside

Wound Ribbon

Inside

Wound Ribbon

NOTE:

To check or change settings on which type of Ribbon winding to be used, you must go to SYSTEM Mode in

the Printer. For more detail refer to Key Operation Specification, “8.4.1 PRINTER SET”.

E-8

4. Turning the Printer ON/OFF

When the printer is connected to your host computer it is good practice to turn the printer ON

before turning on your host computer and turn OFF your host computer before turning off the

printer.

4.1 Turning ON the Printer

1. To turn ON the printer power, press the Power

Switch as shown in the diagram below. Note that

( | ) is the power ON side of the switch.

2. Check that the ON LINE message appears in the

LCD Message Display and that the ON LINE and

POWER LED lights are illuminated.

4.2 Turning OFF the Printer

1. Before turning off the printer Power Switch verify

that the ON LINE message appears in the LCD

Message Display and that the ON LINE LED light

is on and is not flashing.

2. To turn OFF the printer power, press the Power

Switch as shown in the diagram below. Note that

(O) is the power OFF side of the switch.

CAUTION!

Use the power switch to turn the printer On/Off. Plugging or unplugging the Power Cord to turn the

printer On/Off may cause fire, an electric shock, or damage to the printer.

NOTE:

If a message other than ON LINE appears on the display or the ERROR LED lamp is illuminated, refer to

Owners manual, Error Messages.

CAUTION!

1. Do not turn off the printer power while the media is being printed as this may cause a paper jam

or damage to the printer.

2. Do not turn off the printer power while the ON LINE lamp is blinking as this may cause damage

to your computer.

Power Switch

< For EU only >

TOSHIBA TEC Europe Retail Information Systems S.A

Rue de la Célidée 33 BE-1080 Brussels

www.toshibatec-eu.com

by TOSHIBA TEC CORPORATION

84-4 Minamicho, Mishima-shi, Shizuoka-ken,

JAPAN

PRINTED IN INDONESIA

EO1-33097C

Otros manuales para B-EX4 SERIES

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Lector de código de barras de Toshiba

Toshiba

Toshiba B-SX600 SERIES Instrucciones de instalación

Toshiba

Toshiba B-SX8T SERIES Manual de usuario

Toshiba

Toshiba B-EX4 SERIES Manual de usuario

Toshiba

Toshiba B-FV4D SERIES Instrucciones de funcionamiento y mantenimiento

Toshiba

Toshiba B-EX4 T1 Series Manual de usuario

Toshiba

Toshiba B-SA4TP SERIES Manual de usuario

Toshiba

Toshiba TEC B-442 Manual de usuario

Toshiba

Toshiba B-SV4T Instrucciones de instalación

Toshiba

Toshiba BV410T-GS02-QM-S Manual de usuario

Toshiba

Toshiba B-SX4T Series Manual de usuario

Toshiba

Toshiba B-EX4 SERIES Manual de usuario

Toshiba

Toshiba B-852 Advance Manual de usuario

Toshiba

Toshiba B-EP Series Manual de usuario

Toshiba

Toshiba BV420D-GL02-QM-S Manual de usuario

Toshiba

Toshiba B-EX6T Series Manual de usuario

Toshiba

Toshiba B-SV4T Manual de usuario

Toshiba

Toshiba B-SA4TM SERIES Manual de usuario

Toshiba

Toshiba B-EV4 Series Manual de usuario

Toshiba

Toshiba B-EX4T2 SERIES Manual de usuario

Toshiba

Toshiba B-EX4T3 Manual de usuario

Toshiba

Toshiba B-SX4T Series Manual de usuario

Toshiba

Toshiba SX4T - TEC B B/W Direct Thermal Manual de usuario

Toshiba

Toshiba B-EX6 Series Manual de usuario

Toshiba

Toshiba B-SX4 Series Manual de usuario

Manuales populares de Lector de código de barras de otras marcas

POSMicro

POSMicro Datalogic PowerScan D7100 Manual de usuario

Marson

Marson MT780 Guía de configuración rápida

NCR

NCR RealPOS Manual de usuario

Motorola

Motorola SE3300 Guía de configuración rápida

Element

Element P130BT Manual de usuario

Motorola

Motorola Symbol LS3008 Manual de instalación y operación

Meec tools

Meec tools OBD-II / VAG Manual de usuario

SICK

SICK CLP 100 Manual de usuario

Royal Tag SA

Royal Tag SA I-Read Manual de usuario

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manual de usuario

Meteor

Meteor 8310 Manual de usuario

Denso

Denso BHT-500B Manual de usuario

Datalogic

Datalogic Heron HD3130 Manual de usuario

Motorola

Motorola MP6000 Instrucciones de montaje

Newland

Newland NLS-HR15-BT Manual de usuario

ARTDEV

ARTDEV AS-1310 Manual de usuario

Aopos

Aopos AS290 Manual de usuario

ENS

ENS 367-5455 Manual de usuario