Toro 79366 Manual de usuario

Operator’s Manual

IMPORTANT: Read this manual, and your tractor manual, carefully. They

contain information about your safety and the safety of others. Also

become familiar with the controls and their proper use before you operate

the product.

FORM NO. 3322–158 Rev A

Wheel Horse

44” Snowthrower

for

5xi Lawn and Garden Tractors

Model No. 79366 – 9900001 & Up

Printed in USA

Introduction

We want you to be completely satisfied with your

new product, so feel free to contact your local

Authorized Service Dealer for help with service,

genuine replacement parts, or other information you

may require.

Whenever you contact your Authorized Service

Dealer or the factory, always know the model and

serial numbers of your product. These numbers will

help the Service Dealer or Service Representative

provide exact information about your specific

product. You will find the model and serial number

plate located in a unique place on the product as

shown below.

m–3732

Figure 1

1. Modeland Serial Number Plate

For your convenience, write the product model and

serial numbers in the space below.

Model No:

Serial No.

The warning system in this manual identifies

potential hazards and has special safety messages that

help you and others avoid personal injury, even death.

DANGER, WARNING and CAUTION are signal

words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended

precautions are not followed.

WARNING signals a hazard that may cause serious

injury or death if the recommended precautions are

not followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed.

Two other words are also used to highlight

information. “Important” calls attention to special

mechanical information and “Note” emphasizes

general information worthy of special attention.

The left and right side of the machine is determined

by sitting on the seat in the normal operator’s

position.

Contents

Page

Safety and Instruction Decals 2. . . . . . . . . . . . . .

Installation 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loose Parts 3. . . . . . . . . . . . . . . . . . . . . . . . .

Assembling the Snowthrower 5. . . . . . . . . .

Setting Up the Tractor 7. . . . . . . . . . . . . . . .

Installing the Snowthrower on the Tractor 7.

Removing the Snowthrower 12. . . . . . . . . . . .

Operation 16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating the Power Take Off (PTO) 16. . . .

Operating the Attachment Lift Lever 17. . . . .

Adjusting The Discharge Chute 18. . . . . . . . .

Tips for Throwing Snow 18. . . . . . . . . . . . . .

Page

Maintenance 20. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Interval Chart 20. . . . . . . . . . . . . . . .

Greasing and Lubrication 20. . . . . . . . . . . . . .

Replacing the Snowthrower Belt 22. . . . . . . .

Adjusting the Skids 24. . . . . . . . . . . . . . . . . .

Replacing the Scraper Blade 25. . . . . . . . . . .

Adjusting Drive Chain Tension 25. . . . . . . . .

Storage 26. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Safety

Safety and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near

any area of potential danger. Replace any decal that is damaged or lost.

ON TOP OF HOUSING

(Part No. 92–8652)

(2) ON TOP OF HOUSING

(Part No. 63–2380)

ON UPPER DISCHARGE

CHUTE

(Part No. 94–8079)

ON TOP OF PULLEY COVER

(Part No. 98–8705)

Installation

Loose Parts

Note: A rear–mount Attach-A-Matichitch, rear wheel weights (and/or rear weight box**) and chains, all of

which must be purchased separately, are required to operate the tractor equipped with this snowthrower.

Use the chart below to identify parts used for assembly.

**Rear wheel weights may not provide adequate traction under some conditions or on inclines. If these

conditions exist, a rear weight box is recommended.

DESCRIPTION QTY. USE

Snowthrower frame assembly

Lift tube

Clevis pin 1/2” x 2 5/8” (67 mm)

Clevis clip

Attach lift tube

Discharge chute assembly

Washer 5/16” (8 mm)

Locknut 5/16”

Carriage bolt 5/16–18 x 3/4” (19 mm)

Assemble discharge chute

Clevis pin 3/8” x 1” (25 mm)

Hairpin cotter—small

2Prepare tractor attachment lift

Pulley box

Belt

1Install pulley box

Installation

DESCRIPTION USEQTY.

Clevis pin 1/2” x 1” (25 mm)

Clevis clip

Spring tension link

Support rod link

Support brace

Washer 13/16” (21 mm)

Hairpin cotter—large

Washer 15/16” (24 mm)

Crank support

Locking pin

Chute control rod

Hairpin cotter—small

Hairpin cotter–medium

Pulley cover

Screw #10 x 1/2” (13 mm)

Rod Assembly

Spacer washer 1” (25 mm)

“C” shaped pin

Mount snowthrower to tractor

Operator’s Manual 1Read before operating

Installation

Assembling the Snowthrower

Attach Lift Tube

Connect the lift tube to the snowthrower frame

assembly with the 2 5/8” (67 mm) clevis pin and

clip (Fig. 1)

m–3668d

Figure 1

1. Lift tube

2. Snowthrower frame

assembly

3. Clevis pin 2 5/8” (67 mm)

4. Clevis clip

Assemble the Discharge Chute

Install the discharge chute assembly onto the

chute ring with (3) 5/16 x 3/4” (19 mm) carriage

bolts (heads to the inside), (3) 5/16” (8 mm)

washers and (3) 5/16” locknuts (Fig. 2).

m–3719

Figure 2

1. Discharge chute assembly

2. Carriage bolt 5/16 x 3/4”

(19 mm)

3. Washer 5/16” (8 mm)

4. Locknut 5/16”

5. Chute ring

Verify the Drive Chain Tension

Verify that the drive chain has between 1/8” and 1/2”

deflection in the area shown in Figure 3. If the chain

is too tight or too loose, adjust it; refer to Adjusting

Drive Chain Tension, page 25.

m–3795

Figure 3

1. Drive chain 2. Check deflection here

Assemble Spring Tension Link

Insert the hooked end of the spring tension link

into the open hole in the outer leg of the spring

tension lever (Fig. 4).

m–4087

Figure 4

1. Springtension lever

2. Hooked end of spring

tension link

3. Outer leg

Installation

Install Drive Belt and Pulley Cover

1. Route the belt under the four (4) pulleys and

inside the belt guide in the pulley box (Fig. 5).

m–4348

Figure 5

1. Snowthrowerbelt 2. Belt guide

2. Slide the pulley box into the snowthrower frame

(Fig. 6).

3. Route the belt over the snowthrower pulley

(Fig. 6).

m–4342

Figure 6

1. Snowthrowerframe

2. Snowthrower pulley

3. Pulley box

4. Lift tube

5. Belt guide

4. Make certain that the wide side of the PTO drive

belt is toward the outside diameter of all the

pulleys (Fig. 7).

m–4230

ÉÉÉÉ

Figure 7

1. Pulley outside diameter 2. Wide side of belt

5. Attach the pulley cover to the snowthrower

frame assembly with (4) #10 x 1/2” (13 mm)

screws (Fig. 8).

m–4343

Figure 8

1. Pulley cover

2. Screw #10 x 1/2” (13 mm) 3. Snowthrower frame

assembly

Installation

Setting Up the Tractor

Install Rear Wheel Weights and Chains

Install the rear wheel weights and chains. Refer to

Attachment Installation Instructions supplied with the

attachment.

Note: Rear wheel weights may not provide

adequate traction under some

conditions or on inclines. If these

conditions exist, a rear weight box is

recommended.

Install the Rear Attach-A-MaticHitch

Install the rear Attach-A-Matichitch to the tractor;

refer to the Installation Instructions that come with

the Attach-A-Matichitch.

Prepare the Tractor’s Attachment Lift

1. Start the engine.

2. Raise the attachment lift.

3. Set the parking brake and turn the ignition key to

“STOP” to stop the engine. Remove the ignition

key.

4. The two lift arms are attached to the tractor

frame, just ahead of the rear wheels. Secure the

lift arms to the tractor frame with 3/8” x 1”

(25 mm) clevis pins and small hairpin cotters

(Fig. 9).

m–3433

Figure 9

Right side of tractor shown

1. Lift arm

2. Clevis pin 3/8” x 1”

(25 mm)

3. Hairpin cotter–small

These pins must be installed when operating with a

blade, snowthrower, or the tiller attachment.

Note: Remove the pins when attaching a

mower.

Installing the Snowthrower on

the Tractor

1. Position the snowthrower frame assembly and its

attachment parts on a level surface with enough

space behind them to accommodate the tractor.

2. Park the tractor behind the snowthrower with the

front wheels lined up to straddle the snowtrower

frame and lift rod (Fig. 10). Lower the

attachment lift and turn the ignition key to

“STOP” to stop the engine. Remove the ignition

key.

Installation

m–3446

Figure 10

3. With the High–Low range selector in neutral

“N,” pull the tractor forward toward the

snowthrower until the end of the snowthrower

frame is just underneath the tractor’s front

Attach-A-Matichitch (Fig. 11).

4. Ensure the latches on the tractor’s front

Attach-A-Maticare open. Then slide the

pulley box completely into the Attach-A-Matic

hitch. Close the latches by rotating them down

(Fig. 11).

m–4344

Figure 11

1. Attach–A–Matichitch

latches 2. Pulley box

5. Install (2) “C” shaped pins into the locking holes

of the pulley box. Secure them with (2) small

hairpin cotters on the inside (Fig. 12).

m–4345

Figure 12

1. Pulley box

2. “C” shaped pin 3. Attach–A–Maticlatch

4. Hairpin cotter–small

6. Now connect the snowthrower frame to the mid

Attach-A-Matichitch. You will need the crank

support to help with this.

A. Continue pulling the tractor toward the

snowthrower until the snowthrower frame

connecting pins are directly below the mid

Attach–A–Matichitch (Fig. 13)

Otros manuales para 79366

Tabla de contenidos

Otros manuales de Soplador de nieve de Toro

Toro

Toro 38172 CCR Powerlite 325 Manual de usuario

Toro

Toro 38026 Manual de usuario

Toro

Toro Power Max 828 OXE Manual de usuario

Toro

Toro 38536 Manual de usuario

Toro

Toro Flex-Force Power System 31853 Manual de usuario

Toro

Toro Powerlite 38273 Manual de usuario

Toro

Toro Flex-Force Power System 31853 Manual de usuario

Toro

Toro 38657C Manual de usuario

Toro

Toro 38597 Manual de usuario

Toro

Toro CCR 1000 38400 Manual de usuario

Toro

Toro CCR POWERLITE 38172 Manual de usuario

Toro

Toro 1800 Power Curve Manual de usuario

Toro

Toro CCR POWERLITE 38177 Manual de usuario

Toro

Toro 39924 Manual de usuario

Toro

Toro CCR POWERLITE 38172 Manual de usuario

Toro

Toro Power Clear 721 R-C Manual de usuario

Toro

Toro Snow Commander Manual de usuario

Toro

Toro 1800 Power Curve 38381 Manual de usuario

Toro

Toro 38428 Manual de usuario

Toro

Toro Power Shovel Manual de usuario

Toro

Toro PowerMax 826 OE Manual de usuario

Toro

Toro Snow Commander 38601 Manual de usuario

Toro

Toro Power Max Heavy Duty 828 OAE Manual de usuario

Toro

Toro Flex-Force Power System 39901 Manual de usuario

Manuales populares de Soplador de nieve de otras marcas

Murray

Murray 624504X4A Manual de usuario

Blizzard

Blizzard POWER PLOW 8100PP Manual de usuario

Craftsman

Craftsman 486.24837 Manual de usuario

Yard-Man

Yard-Man E2B5 Manual de usuario

ST ST 526 A Manual de usuario

MTD

MTD 3AA Manual de usuario

Ryobi

Ryobi RYAC800 Manual de usuario

Poulan Pro

Poulan Pro 416829 Manual de usuario

Poulan Pro

Poulan Pro 437986 Manual de usuario

MTD

MTD 319-180-00 Manual de usuario

Brute

Brute 1695565 Manual de usuario

Egholm

Egholm City Ranger 2250 Manual de usuario

Poulan Pro

Poulan Pro 420915 Manual de usuario

GreenWorks

GreenWorks SNF402 Manual de usuario

LOFTNESS

LOFTNESS 601D1 Manual de usuario

LOFTNESS

LOFTNESS 1082I Manual de usuario

LOFTNESS

LOFTNESS 481EL Manual de usuario

White Outdoor

White Outdoor 769-01923A Manual de usuario