Toro 30162 Manual de usuario

Operator’s Manual

IMPORTANT: Read this manual carefully. It contains information about your

safety and the safety of others. Also become familiar with the controls and

their proper use before you operate the product.

FORM NO. 3322–131

ProLine

62” Mower

for Mid-Size Traction Unit

Model No. 30162 – 990001 & Up

Printed in USA

Introduction

We want you to be completely satisfied with your

new product, so feel free to contact your local

Authorized Service Dealer for help with service,

genuine replacement parts, or other information you

may require.

Whenever you contact your Authorized Service

Dealer or the factory, always know the model and

serial numbers of your product. These numbers will

help the Service Dealer or Service Representative

provide exact information about your specific

product. You will find the model and serial number

plate located in a unique place on the product as

shown below

1074

1. Model

and Serial Number Plate

For your convenience, write the product model and

serial numbers in the space below.

Model No:

Serial No.

The warning system in this manual identifies

potential hazards and has special safety messages that

help you and others avoid personal injury, even death.

DANGER, WARNING and CAUTION are signal

words used to identify the level of hazard. However,

regardless of the hazard, be extremely careful.

DANGER signals an extreme hazard that will cause

serious injury or death if the recommended

precautions are not followed.

WARNING signals a hazard that may cause serious

injury or death if the recommended precautions are

not followed.

CAUTION signals a hazard that may cause minor or

moderate injury if the recommended precautions are

not followed.

Two other words are also used to highlight

information. “Important” calls attention to special

mechanical information and “Note” emphasizes

general information worthy of special attention.

The left and right side of the machine is determined

in the normal operator’s position.

Contents

Page

Safety and Instruction Decals 2.

. . . . . . . . . . . . .

Assembly 3

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Loose Parts 3

. . . . . . . . . . . . . . . . . . . . . . . . .

Installing the Castor Wheels

. . . . . . . . . . .

Installing the Carrier Frame to the Traction Unit

Installing the Cutting Deck 5

. . . . . . . . . . . .

Installing the Drive Belt 5

. . . . . . . . . . . . . . .

Installing the Flotation Springs 7

. . . . . . . . .

Operation 8

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Side Discharge 8

. . . . . . . . . . . . . . . . . . . . . .

Engaging the Mower Blades (PTO) 8

. . . . . .

Adjusting the Height-of-Cut 9

. . . . . . . . . . .

Adjusting Gage Wheels

. . . . . . . . . . . . . . .

Adjusting the Flotation Springs 10

. . . . . . . . .

Tips for Mowing Grass 11

. . . . . . . . . . . . . . .

Page

Maintenance 12

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Service Interval Chart 12

. . . . . . . . . . . . . . . .

Cutting Blades

. . . . . . . . . . . . . . . . . . . . . .

Correcting Cutting Unit Mismatch 15

. . . . . .

Setting the Front-to-Rear Pitch 15

. . . . . . . . .

Setting the Side-to-Side Leveling 16

. . . . . . .

Greasing the Bearings and Bushings

. . . . .

Adjust Idler Pulley 18

. . . . . . . . . . . . . . . . . . .

Replacing the Deck Belt

. . . . . . . . . . . . . .

Replacing the Drive Belt 19

. . . . . . . . . . . . . .

Replacing the Castor Wheel Fork Bushings

Servicing the Castor Wheels and Bearings 21

Replacing the Grass Deflector 22

. . . . . . . . . .

Storage 22

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting 23

. . . . . . . . . . . . . . . . . . . . . . . . .

Safety

and Instruction Decals

Safety decals and instructions are easily visible to the operator and are located near

any area of potential danger. Replace any decal that is damaged or lost.

See T

raction Unit Operator

’s Manual for

Glossary of Safety Symbols

 " !!  #"" #"

&./ - 

 " !  #"" #"

&./ - 

#  "

&./ - 

 " "   " !!

  #  !!

&./ - 

 " ! 

#"" #"

&./ - 



 "  " "! #" #!!

 !!    % !# 

"  ! "  

 "  "

 "

&./ - 

 " % $" "

  "  "   

 !  #"" #"

&./ -  ()/ !,'(

 !  #"" #"

&./ -  ,*+/ !,'(

 !!  #"" #"

&./ - 0 ()/ !,'(

Assembly

Loose

Parts

Note: Use the chart below to identify parts used for assembly.

DESCRIPTION QTY. USE

Castor Wheel Assembly

Thrust W

asher

Spacer

Retaining Ring

Install castor wheels to carrier frame

Carrier Frame

Flange Screw 1/2–13 x 1” (25 mm)

Flange Nut 1/2–13

Install carrier frame to traction unit

Adjusting Shaft

Jam Nut 1/2–13

Spacer 1/2” (13 mm)

Spring

Bushing

Install adjusting shafts

Clevis Pin

Hairpin Cotter

Install cutting unit to carrier frame

Washer

Cotter Pin

Install flotation springs

Operator’

s Manual

Parts Catalog

Read before operating

Ordering parts

Assembly

Installing

the Castor Wheels

1. Place the (2) thrust washers and spacer onto the

castor wheel fork (Fig. 1).

2. Insert the castor wheel fork into the carrier frame

mounting tube (Fig. 1).

3. Install (2) thrust washers and spacer onto the

castor wheel fork, then secure with a retaining

ring (Fig. 1).



Figure 1

1. Retaining

Ring

Thrust W

asher (4)

Carrier Frame Mounting

Tube

4. Spacer

Castor Wheel Fork

Installing

the Carrier Frame to

the T

raction Unit

1. Align the carrier frame holes with the mounting

holes in the traction unit frame (Fig. 2).

2. Fasten each side of the carrier frame to the

traction unit with three (3) 1/2” x 1” (25 mm)

flange screws and locknuts. Torque the mounting

screws to 60–80 ft-lb (81–109 Nm) (Fig. 2).



Figure 2

1. Carrier

Frame

2. T

raction Unit Frame

Assembly

Installing

the Cutting Deck

1. Position the cutting deck under the carrier frame.

2. Mount the cutting deck to the carrier frame with

four (4) clevis pins and hairpin cotters (Fig. 3).

Note: All four pins must be in the same hole

locations to prevent uneven cutting.

m-4256

Figure 3

1. 2”

(51 mm) Cut Height

2-1/2” (64 mm) Cut Height

3” (76 mm) Cut Height

3-1/2” (89 mm) Cut Height

4” (102 mm) Cut Height

4-1/2” (1

14 mm) Cut

Height

5” (127 mm) Cut Height

Clevis Pin

Carrier Frame

10.

Cutting Deck

11.

Hairpin Cotter

Installing

the Drive Belt

1. Remove the deck covers from the cutting unit.

2. Install the drive belt around the drive pulley on

the traction unit and the upper groove of the

center spindle pulley. The belt must be between

the belt guides (Fig. 4).

3. Reinstall the deck covers onto the cutting unit.

M-4257

Figure 4

1. Belt

Guide (2)

2. T

raction Unit Drive Pulley

Drive Belt

Center Spindle Pulley

Assembly

4. Thread two (2) 1/2” jam nuts approximately 9”

(22.8 cm) up on each adjusting shaft (Fig. 5).

5. Slide a 1/2” spacer, spring and bushing onto each

adjusting shaft. Make sure to install the bushing

with the flange end against the spring (Fig. 5).

m–2542

Figure 5

1. 1/2”

Jam Nut (2)

1/2” Spacer

3. Spring

4. Bushing

Adjusting Shaft

Locknut (already installed

on Adjusting Shaft)

6. Insert the spring end of the adjusting shaft into

the hole in the deck mounting bracket. Note that

the small end of the bushing fits into the hole in

the deck bracket. Insert the locknut end of the

adjusting shaft into the carrier frame mounting

tab (Fig. 6).

7. To tension the belt, tighten the front jam nut on

each adjusting shaft until the springs are

compressed to 5” (12.7 cm). Measure the spring

compression between the spacer and the bushing

(Fig. 6).

8. Tighten the rear jam nuts (Fig. 6).

M-4303

Figure 6

1. 5”

between the Spacer

and Bushing

Deck Mounting Bracket

Front Jam Nut

Rear Jam Nut

Carrier Frame Mounting

Tab

9. Check the position of the belt guides. The guides

should be positioned about 1/8” (3 mm) away

from the belt (Fig. 7). Adjust the belt guides as

necessary.

m-4257

Figure 7

1. Belt

Guide (2)

Drive Belt

10. Check the front-to-rear blade pitch. Refer to

Setting the Front-to-Rear Pitch in the

Maintenance section.

Assembly

Installing

the Flotation Springs

Note: The right side uses the single spring

flotation system (Fig. 9).

1. Move tension bracket rearward into farthest

notch (Fig. 8).

2. Secure cable end to pin on deck support bar with

washer and cotter pin (Fig. 8).

3. Repeat procedure for opposite side of deck

(Fig. 9).

M-4259

Figure 8

1. Tehsion

Bracket

Cotter Pin

3. Washer

Cable End

Deck Support Bar

6. Double

Spring (Left Side)

M-4302

Figure

1. Tehsion

Bracket

Cotter Pin

3. Washer

Cable End

Deck Support Bar

Single Spring (Right Side)

Operation

Side

Discharge

The mower has a hinged grass deflector that disperses

clippings to the side and down toward the turf.

POTENTIAL HAZARD

•Without the grass deflector or complete

grass catcher assembly mounted in place,

you and others are exposed to blade contact

and thrown debris.

WHAT CAN HAPPEN

•Contact with rotating mower blade(s) and

thrown debris will cause injury or death.

HOW TO AV

OID THE HAZARD

•

NEVER r

emove the grass deflector from

the mower because the grass deflector

routes material down toward the turf. If the

grass deflector is ever damaged, replace it

immediately.

•Never put your hands or feet under the

mower.

•Never try to clear discharge area or mower

blades unless you move the power take-off

(PTO) to “OFF” and rotate the ignition key

to “OFF.” Also remove the key and pull the

wire(s) off the spark plug(s).

Engaging

the Mower Blades

(PTO)

The blade control switch (PTO) in conjunction with

the blade control bail engages and disengages power

to the electric clutch and mower blades.

1. Pull on the upper control bar to stop the machine

(Fig. 10).

2. To engage the blades, squeeze the blade control

bail against the upper control bar.

3. Press the blade control rocker switch forward to

“ON”. Hold the blade control bail against the

control bar while operating.

Note: Repeat the procedure to engage the

mower blades if the blade control bail

is released.

4. To disengage the blades, release the blade

control bail, or push the blade control switch to

the “OFF” position.



Figure 10

1. Upper

Control Bar

Blade Control Bail

Blade Control Switch

(PTO)

Tabla de contenidos

Otros manuales de Cortacésped de Toro

Toro

Toro Recycler 22284 Manual de usuario

Toro

Toro Groundsmaster 4500-D Manual de usuario

Toro

Toro 71280 Manual de usuario

Toro

Toro Super Recycler 20092C Manual de usuario

Toro

Toro Z400 Series Z-Master Manual

Toro

Toro Recycler 21771 Manual de usuario

Toro

Toro 71199 Manual de usuario

Toro

Toro 74978 Manual de usuario

Toro

Toro Groundsmaster 360 31200 Series Manual de usuario

Toro

Toro 30446 Manual de usuario

Toro

Toro 74246TE Manual de usuario

Toro

Toro 22178 Manual de usuario

Toro

Toro LX465 Manual de usuario

Toro

Toro 30672 Manual de usuario

Toro

Toro 22176TE Manual de usuario

Toro

Toro Greensmaster 3320 TriFlex Manual de usuario

Toro

Toro TITAN ZX 4800 Manual de usuario

Toro

Toro Recycler 21772 Manual de usuario

Toro

Toro TimeCutter HD MyRide 48in Manual de usuario

Toro

Toro 72029 Manual

Toro

Toro HoverPro 450 Manual de usuario

Toro

Toro 30070 Manual de usuario

Toro

Toro Recycler 20332 Manual de usuario

Toro

Toro LX423 Manual de usuario

Manuales populares de Cortacésped de otras marcas

RHINO

RHINO 1958 Manual de usuario

Wolf Garten

Wolf Garten Compact plus 40 B Manual de usuario

Cub Cadet

Cub Cadet LTX 1045 Manual de usuario

Craftsman

Craftsman 917.378461 Manual de usuario

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manual de usuario

Challenge

Challenge CH18V2 Instrucciones de operación

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manual de usuario

DEWEZE

DEWEZE ATM-725 Manual de operación

Weed Eater

Weed Eater 180083 Manual de usuario

Husqvarna

Husqvarna Poulan Pro PP185A42 Manual de usuario

Better Outdoor Products

Better Outdoor Products Quick Series Manual de usuario

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manual de funcionamiento

MTD

MTD 795, 792, 791, 790 Manual de usuario

Dennis

Dennis FT 610 Manual de usuario

AIRFORCE

AIRFORCE F-15 Gen 3 Manual de usuario

MTD

MTD 126-220-000 Manual de usuario

Stihl

Stihl RMA 443 PV Manual de usuario

Yard-Man

Yard-Man 3700-0 Manual de usuario