Torch-Bigtide HL3116ST Manual de usuario

User Manual

32 inch LCD Monitor

Model: HL3116ST

Rev.: 0.0

Contents

1. Application .......................................................................................................3

2. Declarations .....................................................................................................4

3. Installation.......................................................................................................7

4. Start-up ...........................................................................................................8

4.1 Connecting the power and signal cables........................................................9

4.1.1 Cable (attaching)................................................................................9

4.2 Power up the display .................................................................................10

4.3 Screen saver .............................................................................................10

5. Adjustments...................................................................................................10

5.1 Picture adjustment.....................................................................................10

5.2 Optimum picture quality............................................................................11

6. Fault diagnostics.............................................................................................11

7. Technical data................................................................................................12

7.1 Display......................................................................................................12

7.2 Screen Performance...................................................................................13

7.3 Operation Temperature..............................................................................13

7.4 Transport and storage (Packed)..................................................................13

7.5 Mechanical requirements Operation............................................................14

7.6Mechanical requirements Operation .............................................................14

7.7 Electromagnetic compatibility .....................................................................14

7.8 Environmental information .........................................................................15

7.9 MTBF........................................................................................................15

8. Dimensional drawings .....................................................................................16

9. Cleaning.........................................................................................................16

10. Remarks and contact address........................................................................16

1. Application

This high-resolution color display is specifically designed to meet the rigorous

performance standards needed for diagnostic, with Touch screen

interventional radiology, and other medical applications. To guarantee image

integrity, features include accurate signal conversion and a wide range of

interfacing options.

Compact design - Low weight and small size with improved performance

make the color flat panel display HL3116ST preferable to conventional CRT

monitors.

Grayscale display and calibration

The monitor features smoother and more accurate grayscale gradations with

1024 (10-bit) shades of gray from a palette of 4096(12-bit LUT). At least five

different LUT are built into the monitor, and the monitor is factory calibrated to

achieve DICOM 3.0 Part 14 and other calibrated Gamma value at the factory

set point.

Screen resolution –HL3116ST is equipped with a panel with Super PLS

technology. The optimal picture resolution is 3840 x 2160 pixels. Video

signals with other resolutions typical to medical engineering are optimally

zoomed in or out to the screen size.

Fast backlight stability - The luminance stabilization circuit employs a

built in photo sensor to keep the back-light lamps at a constant luminance for

consistent calibration over the life of the display and can control the back light

system automatically to extend the life of the monitor and achieve very short

warming up time.

Perfect picture reproduction technology

The physical resolution is 3840 x 2160 pixels. Video pictures of other

resolutions are optimally scaled to the screen size in proportion.

High brightness

VESA Hole

The monitor supports 100X100mm , 100X200mm VESA arm mounting.

Multi-interface for video inputs - Support DVI-D(dual), Display Port.

Touch panel-The monitor has protective glass bonding to panel and has

infrared touch screen in the front.

PIP picture-The PIP can be supported .

2. Declarations

Safety precautions

Medical Equipment

With respect to electric shock, Fire and mechanical hazards only in

accordance with ANSI/AAMI ES60601-1: 2005 + A2(R2012) + A1

＆CAN/CSA-C22.2 NO. 60601-1:14

Regular maintenance and calibration are recommended

Please note that liquid crystal displays such as the HL3116ST do not have a

zero failure rate and image parameters may change over time (e.g. luminance

or discoloration). Please ensure that all measures are taken to prevent injuries

or incorrect diagnoses. Regular maintenance and calibration are

recommended.

Correct and safe operation of the flat panel displays is dependent on proper

transport, storage, installation and assembly, as well as careful operation and

maintenance. The units must only be used for applications for which monitors

are normally used. The information in the Section "Technical data" must be

observed exactly.

For the sake of safety, the following precautions must be observed:

Danger: There is a danger to life if the warning information is

observed. Severe personal injury or damage to property may occur.

Do not open the unit yourself

Certain components inside the units are at high-voltage, i.e. touching these

components presents a danger to life!

Do not insert any objects into the housing

Objects inserted into the housing may result in damage to the unit or personal

injury.

Do not place any objects on top of the units

Penetrating liquids may result in a fire or electric shock.

Caution

Incorrect installation may result in extensive damage to property. Installation

should be carried out by trained personnel. In order to prevent injury to

patients and users of your systems, when installing your medical electrical

system with our products in an environment with patients, please observe the

safety requirements of EN 60601-1-1 (IEC 60601-1-1) in "Specifications for

the safety of medical electrical systems".

Take appropriate measures to particularly ensure that discharge

currents remain below the required limits: Appropriate measures:

- Disconnecting devices for signal input or output unit

- Use of a safety transformer

-Close the plug panel using the provided cover, and secure using the screws.

-Turn the switch off and then remove power cord.

Notice for users

The plug panel is closed by the cover, must not be opened by users.

Servicing information

If housing components have to be removed for servicing, this must not be

carried out in the presence of patients, the user, or other persons not involved

with servicing. The following applies to installations in the USA and Canada:

Molded power supply plugs must comply with the requirements for "Hospital

Grade Attachments" UL 498.

Caution

Failure to observe the warnings may result in substantial damage to

property.

Provide sufficient heat dissipation

Slots are provided at the rear of the housing. The display must be placed or

secured on a hard, level surface at least 10cm from the wall and 15cm away

from other devices. Several displays can be butt-mounted horizontally and

vertically.

The following must be observed when mounting (VESA connection):

Mounting screws

Number 4

Thread M6

Immersion depth Max. 15 mm

Torque Max. 12Nm

Mounting screws

The permissible ambient temperature range (10 °C ... 35 °C) must not be

violated. Do not subject device to unnecessary shocks. Take care when

transporting! Use the original packaging! The panel in particular should be

protected against shocks.

When touching the panel surface, the mechanical contact or an electrical

discharge may cause a brief disturbance in the picture quality.

Care of unit / cleaning agents

−The front panel is extremely sensitive to mechanical damage. Avoid all

scratches, knocks etc.!

−Remove water drops immediately which will discolor the surface. Clean the

front panel when dirty, using a micro fiber cloth and, if necessary, a glass

cleaning agent. Only clean housing parts using a cleaning agent for plastics.

Note:

Do not use cleaning agents containing solvent, e.g. petroleum

Explanation of the symbols

Direct current (DC)

China RoHS symbol

EC W EC WEEE symbol

European conformity

TUV approval mark

Attention: Consult the accompanying documents

3. Installation

Provide adequate ventilation

Ventilation slots are located on the rear of the housing.

Ambient temperature

The permissible ambient temperature range must not be violated.

Minimize reflections

The display should be positioned so that reflections of lights, windows,

furniture with shiny surfaces or light-colored walls do not appear on the screen.

Minimize mirroring

In order to reduce mirroring on the unit, ceiling lighting or reflected light (no

dazzling) should be used. Mirroring can only be eliminated if the screen is

clean and free of grease. Clean the display using a suitable micro fiber cloth.

Change of environment

If the unit is brought into a warm environment from a cold one, water may

condense upon it. The unit should not be switched on until all the condensed

water has evaporated, including that inside the unit. This may take several

hours, depending on the conditions.

4. Start-up

Caution

In order to ensure safe operation of the equipment, close attention must be

paid to the information contained in this Instruction Manual as well as the

warnings in Section 2 "Safety precautions".

Caution Information for end customer

None of the settings must be changed on site by the user, otherwise the

guarantee is canceled. This also applies to settings made using the

HL3116ST keys. These are therefore locked for certain applications. If

settings have to be changed, please contact the responsible servicing

department.

The display is designed for individual connection to a graphics card with a

power supply of 100 or 240 Volt (TN-S system with PE conductor). If the

display is to be used in a sequence of several displays, or if it is not exactly

known whether the graphics card standard can be output by the display, refer

to Section 5.1 "Connection of the flat panel display".

In order to start the unit properly, the following steps should be carried out in

the given sequence.

4.1 Connecting the power and signal cables

Warning

The display can be tilted backwards and forwards. Please pay attention not to

hurt yourself, when moving the display. Fingers or small objects may get stuck

at the bottom of the display.

Caution

Use a power cable with PE conductor corresponding to the safety

requirements of the respective country of use. Note for North America:

Molded power supply plugs must comply with the requirements for hospitals

with respect to CSA Std. C22.2 No. 21 and UL 498.The power supply and

signal connections are located on the rear of the color flat panel display.

Note

Note that the cables are already positioned when you receive the display

(power cable and DVI-D cable). The following steps are only necessary if you

need to connect/ disconnect the cables of the scope of supply.

4.1.1 Cable (attaching)

Connect the cables to the display.

Power cable: The Power cable connection is used for display power supply.

DVI-D connection: The connection to the computer can be made via the

digital single link. The picture quality, noise immunity and radiated

interference of the complete system depend on the cable quality and length.

DP connection: The connection to the computer can also be made via the

Display Port connection. The picture quality, noise immunity and radiated

interference of the complete system depend on the cable quality and length.

4.2 Power up the display

Use the power switch to power up the flat panel display. The operation LED

lights up (color: green)

4.3 Screen saver

A screen saver function should be used in order to reduce "image sticking"

which can occur in TFT displays.

It is high risk to display a static graphic over half an hour.

Image sticking is the effect where a faint image of the previous screen

contents can still be seen after the display contents have changed. By using a

screen saver with permanently changing screen contents, unnecessary

effects of the same image are avoided.

If the keyboard is locked, contact the servicing department in order to unlock it.

The guarantee is cancelled if you unlock it yourself!

5. Adjustments

5.1 Picture adjustment

This section describes the settings for operation of the flat panel display with a

video source.

Fine adjustment of the flat panel display

Tabla de contenidos

Otros manuales de Monitor de Torch-Bigtide

Torch-Bigtide

Torch-Bigtide HL1916S SERIAL Manual de usuario

Torch-Bigtide

Torch-Bigtide HL1916SH Manual de usuario

Manuales populares de Monitor de otras marcas

Linear Acoustic

Linear Acoustic LQ-1000 Manual de usuario

AOC

AOC I2579V Manual de usuario

Gateway

Gateway FPD1520 Manual de usuario

Furuno

Furuno Mu 120c Manual de usuario

Asus

Asus VB171D - 17" LCD Monitor Manual de usuario

Dell

Dell S2230MX Instrucciones de uso

Philips

Philips 107C64 Manual de usuario

Dell

Dell S2409WFP Manual de usuario

EverFocus

EverFocus EN-7517E Manual de usuario

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Manual de usuario

Dell

Dell Precision 7680 Manual de instrucciones

LG 50PM1M - - 50" Plasma Panel Manual de usuario

Bosch

Bosch DDU 9 Manual de usuario

Acer

Acer A231HL Manual de usuario

Philips

Philips 86BDL4152T Manual de usuario

NEC

NEC AccuSync LCD5V Manual de usuario

Emay

Emay SleepO2 Manual de usuario

IBM

IBM 6360 Instrucciones de instalación